Hostname: page-component-78c5997874-mlc7c Total loading time: 0 Render date: 2024-11-01T21:23:43.506Z Has data issue: false hasContentIssue false
  • English
  • Français

Tribological characteristics of polycrystalline diamond films produced by chemical vapor deposition

Published online by Cambridge University Press:  31 January 2011

M. Kohzaki ,
K. Higuchi ,
S. Noda  and
K. Uchida
M. Kohzaki
Affiliation:
Toyota Central Research and Development Laboratories, Inc., Nagakute-cho, Aichi-gun, Aichi-ken, 480-11 Japan
K. Higuchi
Affiliation:
Toyota Central Research and Development Laboratories, Inc., Nagakute-cho, Aichi-gun, Aichi-ken, 480-11 Japan
S. Noda
Affiliation:
Toyota Central Research and Development Laboratories, Inc., Nagakute-cho, Aichi-gun, Aichi-ken, 480-11 Japan
K. Uchida
Affiliation:
Toyota Central Research and Development Laboratories, Inc., Nagakute-cho, Aichi-gun, Aichi-ken, 480-11 Japan
Get access

Abstract

Effects of surface roughness and crystallinity of polycrystalline diamond films on their tribological characteristics, as well as the effects of test environment, have been investigated. Friction and wear characteristics of the diamond films deposited on sintered SiC disks have been examined with a ball-on-disk tester in the absence of any lubricant. The friction coefficients of polished diamond films against SiC and Si3N4 balls were below 0.10 at room temperature while those of as-deposited films were around 0.20. The specific wear of counterparts on the polished film was five orders of magnitude smaller than on the as-deposited film. The friction coefficient between the polished diamond film and a AISI 52100 steel ball was about 0.20. Transfer of a small amount of AISI 52100 material to the diamond film was observed along the wear track of the polished diamond surface. Diamond films of high quality were more resistant to wear than the ones of low quality. On the other hand, the friction coefficients were not affected by the crystallinity of the diamond films in the present study. Tribological characteristics of the diamond films deteriorated with increasing sliding speed and ambient temperature. At 600 °C in dry N2, the friction coefficient of diamond films against a SiC ball was about 0.8, which was about ten times higher than that at room temperature in air.

Type
Articles
Information
Journal of Materials Research , Volume 7 , Issue 7 , July 1992 , pp. 1769 - 1777
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Matsumoto, S., Sato, Y., Tsutsumi, M., and Setaka, N., J. Mater. Sci. 17, 3106 (1982).CrossRefGoogle Scholar
2.Sawabe, A. and Inuzuka, T., Thin Solid Films 197, 89 (1986).CrossRefGoogle Scholar
3.Kamo, M., Sato, Y., Matsumoto, S., and Setaka, N., J. Cryst. Growth 62, 642 (1983).CrossRefGoogle Scholar
4.Crompton, D., Hirst, W., and Howse, M. G. W., Proc. Roy. Soc. A333, 455 (1973).Google Scholar
5.Casey, M. and Wilks, J., J. Phys. D: Appl. Phys. 6, 1772 (1973).CrossRefGoogle Scholar
6.Enomoto, Y. and Tabor, D., Proc. Roy. Soc. A373, 405 (1981).Google Scholar
7.Samuels, B. and Wilks, J., J. Mater. Sci. 23, 2846 (1988).CrossRefGoogle Scholar
8.Jahanmir, S., Deckman, D. E., Ives, L. K., Feldman, A., and Farabaugh, E., Wear 133, 73 (1989).CrossRefGoogle Scholar
9.Wong, M. S., Meilunas, R., Ong, T. P., and Chang, R. P. H., Appl. Phys. Lett. 54, 2006 (1989).CrossRefGoogle Scholar
10.Kuo, C-T., Yen, T-Y., Huang, T-H., and Hsu, S. E., J. Mater. Res. 5, 2515 (1990).CrossRefGoogle Scholar
11.Gardos, M. N. and Soriano, B. L., J. Mater. Res. 5, 2599 (1990).CrossRefGoogle Scholar
12.Bowden, F. P. and Hanewell, A. E., Proc. Roy. Soc. A295, 233 (1966).Google Scholar
13.Pate, B. B., Surf. Sci. 165, 83 (1986).CrossRefGoogle Scholar
14.Matsumoto, S., Sato, Y., and Setaka, N., Carbon 19, 232 (1981).CrossRefGoogle Scholar
15.Pepper, S. V., J. Vac. Sci. Technol. 20, 643 (1982).CrossRefGoogle Scholar
16.Casey, M. and Wilks, J., J. Phys. D: Appl. Phys. 6, 1772 (1973).CrossRefGoogle Scholar