Hostname: page-component-78c5997874-4rdpn Total loading time: 0 Render date: 2024-11-19T08:21:05.377Z Has data issue: false hasContentIssue false
  • English
  • Français

Property engineering in BaTiO3 films by stoichiometry control

Published online by Cambridge University Press:  31 January 2011

J.F. Ihlefeld ,
P.R. Daniels ,
S.M. Aygün ,
W.J. Borland  and
J-P. Maria
J.F. Ihlefeld*
Affiliation:
Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27606; and Materials Science and Engineering Center, Sandia National Laboratories, Albuquerque, New Mexico 87185
S.M. Aygün
Affiliation:
Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27606
W.J. Borland
Affiliation:
Dupont Electronic Technologies, Research Triangle Park, North Carolina 27709
J-P. Maria*
Affiliation:
Department of Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27606
*
a)Address all correspondence to this author. e-mail: jihlefe@sandia.gov
b)Address all correspondence to this author. e-mail: jpmaria@ncsu.edu
Get access

Abstract

BaTiO3 thin films were prepared on metallic foil substrates using chemical solution deposition. The impact of A to B site cation ratios on the phase assemblage and microstructural and dielectric properties was investigated by characterizing a sample set that includes stoichiometric BaTiO3 and 1, 2, 3, 4, and 5 mol% excess BaO. Each composition was subjected to a high-temperature anneal step with maximum dwell temperatures of 1000, 1100, and 1200 °C for 20 h. Excess barium concentrations greater than 3% lead to dramatic grain growth and average grain sizes exceeding 1 μm. Despite the large deviations from stoichiometry and the 20 h dwell time at temperature, x-ray diffraction, and high-resolution electron microscopy analysis were unable to detect secondary phases until films with 5% excess barium were annealed to 1200 °C. Thin films with 3% excess barium were prepared on copper substrates and annealed at 1060 °C, the practical limit for copper. This combination of BaO excess and annealing temperature produced an average lateral grain size of 0.8 μm and a room-temperature permittivity of 4000. This is in comparison to a permittivity of 1800 for stoichiometric material prepared using identical conditions. This work suggests metastable solubility of BaO in BaTiO3 that leads to enhanced grain growth and large permittivity values. This technique provides a new solid-state means of achieving grain growth in low thermal budget systems.

Keywords

Dielectric propertiesFerroelectricThin film
Type
Articles
Information
Journal of Materials Research , Volume 25 , Issue 6 , June 2010 , pp. 1064 - 1071
Copyright
Copyright © Materials Research Society 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Jillek, W., Yung, W.K.C.Embedded components in printed circuit boards: A processing technology review. Int. J. Adv. Manuf. Technol. 25, 350 (2005)CrossRefGoogle Scholar
2.Kim, D.J., Kaufman, D.Y., Streiffer, S.K., Lee, T.H., Erck, R., Auciello, O.Chemical solution deposition of PLZT films on base metal foilsFerroelectric Thin Films XI edited by D.Y. Kaufman, S. Hoffmann-Eifert, S.R. Gilbert, A. Aggarwal, and M. Shimizu (Mater. Res. Soc. Symp. Proc 748, Warrendale, PA 2003)457462Google Scholar
3.Ihlefeld, J., Laughlin, B., Hunt-Lowery, A., Borland, W., Kingon, A., Maria, J-P.Copper compatible barium titanate thin films for embedded passives. J. Electroceram. 14, 95 (2005)CrossRefGoogle Scholar
4.Losego, M.D., Jimison, L.H., Ihlefeld, J.F., Maria, J-P.Ferroelectric response from lead zirconate titanate thin films prepared directly on low-resistivity copper substrates. Appl. Phys. Lett. 86, 172906 (2005)CrossRefGoogle Scholar
5.Maria, J-P., Cheek, K., Streiffer, S., Kim, S.H., Dunn, G., Kingon, A.Lead zirconate titanate thin films on base-metal foils: An approach for embedded high-permittivity passive components. J. Am. Ceram. Soc. 84, 2436 (2001)CrossRefGoogle Scholar
6.Saegusa, K.Preparation and electrical properties of sol-gel derived lead zirconate titanate glass-ceramic thin films on metal foil substrates. Jpn. J. Appl. Phys. 1, (36)6888 (1997)CrossRefGoogle Scholar
7.Zou, Q., Ruda, H.E., Yacobi, B.G., Saegusa, K., Farrell, M.Dielectric properties of lead zirconate titanate thin films deposited on metal foils. Appl. Phys. Lett. 77, 1038 (2000)CrossRefGoogle Scholar
8.Sigman, J., Brennecka, G.L., Clem, P.G., Tuttle, B.A.Fabrication of perovskite-based high-value integrated capacitors by chemical solution deposition. J. Am. Ceram. Soc. 91, 1851 (2008)CrossRefGoogle Scholar
9.Dechakupt, T., Yang, G., Randall, C.A., Trolier-McKinstry, S., Reaney, I.M.Chemical solution-deposited BaTiO3 thin films on Ni foils: Microstructure and interfaces. J. Am. Ceram. Soc. 91, 1845 (2008)CrossRefGoogle Scholar
10.Morita, K., Mizuno, Y., Kishi, H.Reliability design of multilayer ceramic capacitor against thinning of dielectric layersProceedings of the 16th IEEE International Symposium on Applications of Ferroelectrics (IEEE, New York 2007)549552Google Scholar
11.Arlt, G., Hennings, D., de With, G.Dielectric-properties of fine-grained barium-titanate ceramics. J. Appl. Phys. 58, 1619 (1985)CrossRefGoogle Scholar
12.Aygun, S.M., Daniels, P., Borland, W., Maria, J.P.Hot sputtering of barium strontium titanate on nickel foils. J. Appl. Phys. 103, 084123 (2008)CrossRefGoogle Scholar
13.Ihlefeld, J.F., Borland, W.J., Maria, J-P.Enhanced dielectric and crystalline properties in ferroelectric barium titanate thin films. Adv. Funct. Mater. 17, 1199 (2007)CrossRefGoogle Scholar
14.Ihlefeld, J.F., Vodnick, A.M., Baker, S.P., Borland, W.J., Maria, J-P.Extrinsic scaling effects on the dielectric response of ferroelectric thin films. J. Appl. Phys. 103, 074112 (2008)CrossRefGoogle Scholar
15.Frey, M.H., Xu, Z., Han, P., Payne, D.A.The role of interfaces on an apparent grain size effect on the dielectric properties for ferroelectric barium titanate ceramics. Ferroelectrics 206, 337 (1998)CrossRefGoogle Scholar
16.Saad, M.M., Baxter, P., Bowman, R.M., Gregg, J.M., Morrison, F.D., Scott, J.F.Intrinsic dielectric response in ferroelectric nano-capacitors. J. Phys. Condens. Matter 16, L451 (2004)CrossRefGoogle Scholar
17.Ihlefeld, J.F.Synthesis and properties of barium titanate solid solution thin films on copper substrates. Ph.D. dissertation in Materials Science and Engineering (North Carolina State University 2006)Google Scholar
18.Hoffmann, S., Waser, R.Control of the morphology of CSD-prepared (Ba,Sr)TiO3 thin films. J. Eur. Ceram. Soc. 19, 1339 (1999)CrossRefGoogle Scholar
19.Schwartz, R.W., Clem, P.G., Voigt, J.A., Byhoff, E.R., Van Stry, M., Headley, T.J., Missert, N.A.Control of microstructure and orientation in solution-deposited BaTiO3 and SrTiO3 thin films. J. Am. Ceram. Soc. 82, 2359 (1999)CrossRefGoogle Scholar
20.Dawley, J.T., Clem, P.G.Dielectric properties of random and 〈100〉 oriented SrTiO3 and (Ba,Sr)TiO3 thin films fabricated on 〈100〉 nickel tapes. Appl. Phys. Lett. 81, 3028 (2002)CrossRefGoogle Scholar
21.Standard test methods for determining average grain size. ASTM E 112-96Annual Book of ASTM Standards (ASTM International, West Conshohocken, PA 2003)Google Scholar
22.von Hippel, A., Breckenridge, R.G., Chesley, F.G., Tisza, L.High-dielectric constant ceramics. Ind. Eng. Chem. 38, 1097 (1946)CrossRefGoogle Scholar
23.Parker, C.B., Maria, J.P., Kingon, A.I.Temperature and thickness dependent permittivity of (Ba,Sr)TiO3 thin films. Appl. Phys. Lett. 81, 340 (2002)CrossRefGoogle Scholar
24.Sharma, R.K., Chan, N.H., Smyth, D.M.Solubility of TiO2 in BaTiO3. J. Am. Ceram. Soc. 64, 448 (1981)CrossRefGoogle Scholar
25.Hu, Y.H., Harmer, M.P., Smyth, D.M.Solubility of BaO in BaTiO3. J. Am. Ceram. Soc. 68, 372 (1985)CrossRefGoogle Scholar
26.Maria, J-P., Wickaksana, D., Parrette, J., Kingon, A.I.Crystallization in SiO2-metal oxide alloys. J. Mater. Res. 17, 1571 (2002)CrossRefGoogle Scholar
27.Barin, I.Thermochemical Data of Pure Substances (VCH, Weinheim, Federal Republic of Germany, New York 1989)Google Scholar
28.Frey, M.H., Payne, D.A.Grain-size effect on structure and phase transformations for barium titanate. Phys. Rev. B: Condens. Matter 54, 3158 (1996)CrossRefGoogle ScholarPubMed
29.Lee, S., Liu, Z.K., Kim, M.H., Randall, C.A.Influence of nonstoichiometry on ferroelectric phase transition in BaTiO3. J. Appl. Phys. 101, 054119 (2007)CrossRefGoogle Scholar
30.Lee, S., Randall, C.A., Liu, Z.K.Modified phase diagram for the barium oxide-titanium dioxide system for the ferroelectric barium titanate. J. Am. Ceram. Soc. 90, 2589 (2007)CrossRefGoogle Scholar
31.Lee, S., Randall, C.A., Liu, Z.K.Comprehensive linkage of defect and phase equilibria through ferroelectric transition behavior in BaTiO3-based dielectrics: Part 1. Defect energies under ambient air conditions. J. Am. Ceram. Soc. 91, 1748 (2008)CrossRefGoogle Scholar
32.Lee, S., Randall, C.A., Liu, Z.K.Comprehensive linkage of defect and phase equilibria through ferroelectric transition behavior in BaTiO3-based dielectrics: Part 2. Defect modeling under low oxygen partial pressure conditions. J. Am. Ceram. Soc. 91, 1753 (2008)CrossRefGoogle Scholar
33.Lin, T.F., Hu, C.T., Lin, I.N.Influence of stoichiometry on the microstructure and positive temperature-coefficient of resistivity of semiconducting barium-titanate ceramics. J. Am. Ceram. Soc. 73, 531 (1990)CrossRefGoogle Scholar
34.Kulcsar, F.A microstructure study of barium titanate ceramics. J. Am. Ceram. Soc. 39, 13 (1955)CrossRefGoogle Scholar
35.Tang, C.Q., Yao, S.The defects, grain size and electrical property in the non-stoichiometric BaTiO3 ceramics. Cryst. Res. Technol. 35, 609 (2000)3.0.CO;2-U>CrossRefGoogle Scholar
36.Lewis, G.V., Catlow, C.R.A.Computer modeling of barium-titanate. Radiat. Eff. Defects Solids 73, 307 (1983)CrossRefGoogle Scholar