Hostname: page-component-78c5997874-8bhkd Total loading time: 0 Render date: 2024-11-01T20:06:39.975Z Has data issue: false hasContentIssue false
  • English
  • Français

Superplasticity of Ultra-High Carbon Steels Containing 3-5%Aluminum

Published online by Cambridge University Press:  16 February 2011

Dong-Wha Kum ,
Hyung Kang  and
Tong-Hoon Kim
Dong-Wha Kum
Affiliation:
Korea Institute of Science and Technology, Div. of Metals, P.O. Box 131, Cheongryang, Seoul Korea
Hyung Kang
Affiliation:
Seoul National Univesity, Dept. of Metallurgical Engineering, San 56-1, Kwanakgu, Seoul Korea
Tong-Hoon Kim
Affiliation:
Seoul National Univesity, Dept. of Metallurgical Engineering, San 56-1, Kwanakgu, Seoul Korea
Get access

Abstract

To study the effect of Al on superplasticity of ultra-high carbon steel (UHCS), 3–5%Al was added to the UHCS, and superplastic behavior was measured at 700–800°C. To produce the fine and superplastic microstructure, an isothermal rolling at 700°C was used, and the grain size of ferrite was less than about 2μm in diameter after the process.

Significant improvement in superplasticity was observed; the strain-rate sensitivity was high upto a strain-rate of 10−2 s−1, and 402% elongation was measured at 750°C and at an engineering strain-rate of 5000%/min(i.e., 8.3×10−2s−1). It has been determined that the Al-addition leads to a finer grain size, which, in turn, improved the superplastic properties of the ultra-high carbon steels.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 196: Symposium T – Superplasticity in Metals, Ceramics, and Intermetallics , 1990 , 209
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Walser, B. and Sherby, O.D., Metall. Trans. 10A, 1461 (1979).Google Scholar
2. Sherby, O.D., Oyama, T., Kum, D.W., Walser, B. and Wadsworth, J., J. Metals 37 (6) 50, (1985).Google Scholar
3. Wadsworth, J. and Sherby, O.D., J. Mater. Sci. 13, 2645 (1978).Google Scholar
4. Raghunathan, V.S. and Sharrna, B.D., Phil. Mag. A, 43 (2), 427–440 (1981).Google Scholar
5. Oyama, T., Sherby, O.D., Wadsworth, J. and Walser, B., Scripta Metall. 18, 799 (1984).Google Scholar
6. Sherby, O.D., Kum, D.W., Oyarna, T. and Wadsworth, J., U.S. Patent No. 4 769 214 (Sept. 6 1988).Google Scholar
7. Langdon, T.G., Metall. Trans. 13A, 689 (1982).Google Scholar
8. Sherby, O.D. and Wadsworth, J., 1982 ASM Materials Science SeminarDeformation, Processing and Strudture, St. Louis, Mi, October 1982, pp.355–389 Google Scholar
9. Gifkins, R.C., Metall. Trans. 7A, 1225 (1976).Google Scholar
10. Ashby, M.F. and Verrall, R.A., Acta Metall. 21, 149 (1973).Google Scholar