This paper presents a multi-band rectangular slot antenna, which can be used in Beidou navigation system, 4G, WLAN and 5G system. The proposed antenna adopts a single feeding line, generating circular polarization for satellite navigation, and linear polarization for mobile communication systems. The proposed antenna consists of three c-type resonators and three rectangular loop slots. A c-type resonator and a rectangular loop slot work together to produce a usable frequency band. Multiple frequency bands can be generated by increasing the number of c-type resonator and rectangular loop slots. It is found that the c-type resonator changes the current distribution on the antenna surface, making the axial ratio less than 3 dB in the low frequency bands. Eventually, five operation frequency bands are realized. Experimentally, it is verified that the impedance bandwidths of each frequency band are 11.8% (1.12–1.26 GHz), 15.4% (1.5–1.75 GHz), 11.9% (2.36–2.66 GHz), 19.7% (3.15–3.84 GHz) and 2.6% (4.47–4.59 GHz), respectively. The measured 3 dB axial ratio bandwidths are 20 MHz at 1.2 and 1.56 GHz, fully covering BDS B1 and B2 bands. The measured gains are 3, 3.59, 4.07, 4.2 and 4.35 dBi, respectively.

We demonstrate an ultra-broadband high temporal contrast infrared laser source based on cascaded optical parametric amplification, hollow-core fiber (HCF) and second harmonic generation processes. In this setup, the spectrum of an approximately 1.8 μm laser pulse has near 1 μm full bandwidth by employing an argon gas-filled HCF. Subsequently, after frequency doubling with cascaded crystals and dispersion compensation by a fused silica wedge pair, 9.6 fs (~3 cycles) and 150 μJ pulses centered at 910 nm with full bandwidth of over 300 nm can be generated. The energy stability of the output laser pulse is excellent with 0.8% (root mean square) over 20 min, and the temporal contrast is >1012 at –10 ps before the main pulse. The excellent temporal and spatial characteristics and stability make this laser able to be used as a good seed source for ultra-intense and ultrafast laser systems.

A ubiquitous arrangement in nature is a free-flowing fluid coupled to a porous medium, for example a river or lake lying above a porous bed. Depending on the environmental conditions, thermal convection can occur and may be confined to the clear fluid region, forming shallow convection cells, or it can penetrate into the porous medium, forming deep cells. Here, we combine three complementary approaches – linear stability analysis, fully nonlinear numerical simulations and a coarse-grained model – to determine the circumstances that lead to each configuration. The coarse-grained model yields an explicit formula for the transition between deep and shallow convection in the physically relevant limit of small Darcy number. Near the onset of convection, all three of the approaches agree, validating the predictive capability of the explicit formula. The numerical simulations extend these results into the strongly nonlinear regime, revealing novel hybrid configurations in which the flow exhibits a dynamic shift from shallow to deep convection. This hybrid shallow-to-deep convection begins with small, random initial data, progresses through a metastable shallow state and arrives at the preferred steady state of deep convection. We construct a phase diagram that incorporates information from all three approaches and depicts the regions in parameter space that give rise to each convective state.

We report on a vortex laser chirped-pulse amplification (CPA) system that delivers pulses with a peak power of 45 TW. A focused intensity exceeding 1019 W/cm2 has been demonstrated for the first time by the vortex amplification scheme. Compared with other schemes of strong-field vortex generation with high energy flux but narrowband vortex-converting elements at the end of the laser, an important advantage of our scheme is that we can use a broadband but size-limited q-plate to realize broadband mode-converting in the front end of the CPA system, and achieve high-power amplification with a series of amplifiers. This method is low cost and can be easily implemented in an existing laser system. The results have verified the feasibility to obtain terawatt and even petawatt vortex laser amplification by a CPA system, which has important potential applications in strong-field laser physics, for example, generation of vortex particle beams with orbital angular momentum, fast ignition for inertial confinement fusion and simulation of the extreme astrophysical environment.

Previously reported wearable systems for people with Parkinson’s disease (PD) have been focused on the detection of abnormal gait. They suffered from limited accuracy, large latency, poor durability, comfort, and convenience for daily use. Herewith we report an intelligent wearable system (IWS) that can accurately detect abnormal gait in real-time and provide timely cueing for PD patients. The system features novel sensitive, comfortable and durable plantar pressure sensing insoles with a highly compressed data set, an accurate and fast gait algorithm, and wirelessly controlled timely sensory cueing devices. A total of 29 PD patients participated in the first phase without cueing for developing processes of the algorithm, which achieved an accuracy of over 97% for off-line detection of freezing of gait (FoG). In the second phase with cueing, the evaluation of the whole system was conducted with 16 PD subjects via trial and a questionnaire survey. This system demonstrated an accuracy of 94% for real-time detection of FoG and a mean latency of 0.37 s between the onset of FoG and cueing activation. In questionnaire survey, 88% of the PD participants confirmed that this wearable system could effectively enhance walking, 81% thought that the system was comfortable and convenient, and 70% overcame the FoG. Therefore, the IWS makes it an effective, powerful, and convenient tool for enhancing the mobility of people with PD.

We show that the Stokes–Darcy system, which governs flows through adjacent porous and pure-fluid domains in the two-domain approach without forced filtration, can be recovered from the Helmholtz minimal dissipation principle. While the continuity of normal velocity across the interface is imposed explicitly for mass conservation, only the Beavers–Joseph–Saffman–Jones (BJSJ) interface boundary condition is imposed implicitly, and the balance of the normal-force interface boundary condition appears naturally in the variational process. This set of interface boundary conditions is well-accepted in the mathematics community. We show that these interfacial boundary conditions, at the physically important small-Darcy-number regime, are consistent with continuity of pressure across the interface condition. The tangential velocity and pressure are discontinuous in general but the discontinuity is of the order of the square root of the Darcy number. Hence these interfacial conditions are all approximately consistent in the physically important small-Darcy-number regime. The leading order dynamics in the pure fluid zone is governed by the Stokes system with the no-slip no-penetration boundary condition on the interface between the free zone and porous media at a small Darcy number. The leading order non-trivial dynamics in porous media is governed by the Darcy equation with the pressure on the interface prescribed by the pressure of the leading order Stokes flow in the pure fluid zone. Such a semi-decoupled approach has long been used by the groundwater community. Our result is the first rigorous work quantifying the error of this intuitive approach and relating different interfacial conditions.

Power scaling based on traditional ytterbium-doped fibers (YDFs) is limited by optical nonlinear effects and transverse mode instability (TMI) in high-power fiber lasers. Here, we propose a novel long tapered fiber with a constant cladding and tapered core (CCTC) along its axis direction. The tapered-core region of the fiber is designed to enhance the stimulated Raman scattering (SRS) threshold and suppress higher-order mode resonance in the laser cavity. The CCTC YDF was fabricated successfully with a modified chemical vapor deposition (MCVD) method combined with solution doping technology, which has a cladding diameter of 400 μm and a varying core with a diameter of ~24 μm at both ends and ~31 μm in the middle. To test the performance of the CCTC fiber during high-power operation, an all-fiber laser oscillator based on a CCTC YDF was investigated experimentally. As a result, a maximum output power of 3.42 kW was achieved with an optical-to-optical efficiency of 55.2%, although the TMI effect was observed at an output power of ~3.12 kW. The measured beam quality (M2 factor) was ~1.7, and no sign of the Raman component was observed in the spectrum. We believe that CCTC YDF has great potential to simultaneously mitigate the SRS and TMI effects, and further power scaling is promising by optimizing the structure of the YDF.

The laser shock processing implemented by a laser-induced high-pressure plasma which propagates into the sample as a shockwave is innovatively applied as a post-processing technique on HfO2/SiO2 multilayer coatings for the first time. The pure mechanical post-processing has provided evidence of a considerable promotion effect of the laser-induced damage threshold, which increased by a factor of about 4.6 with appropriate processing parameters. The promotion mechanism is confirmed to be the comprehensive modification of the intrinsic defects and the mechanical properties, which made the applicability of this novel post-processing technique on various types of coatings possible. Based on experiments, an interaction equation for the plasma pressure is established, which clarifies the existence of the critical pressure and provides a theoretical basis for selecting optimal processing parameters. In addition to the further clarification of the underlying damage mechanism, the laser shock post-processing provides a promising technique to realize the comprehensive and effective improvement of the laser-induced damage resistance of coatings.

Stable isotope ratios (δ18O and δD) in Antarctic snow and ice are basic proxy indices of climate in ice core studies. The relation between the ratios has important indicative significance for moisture sources. In general, the fractionation characteristics of the two isotopes vary with different meteorological and topographical conditions. This paper presents the spatial and temporal distribution of meteoric water line (MWL) slopes along a traverse from the Zhongshan Station (ZSS) to Dome A in East Antarctica. It is found that the slopes decrease with the increasing distance inland from the coast and the lowest slope occurred at Dome A, where the long-range transported moisture dominates and clear sky snowing have an influence. The slopes in different layers of the snowpack showed a decreasing trend with depth and this is attributed to the fractionation during the interstitial sublimation and re-condensation processes of the water vapor. Frost flower development on the interior plateau surface can greatly alter the depth evolution of the MWL slope. The coastal snow pits also go through the post-depositional smoothing effect, but their influences are not so significant as the inland regions.

Linoleic acid (LA) is predominantly essential for poultry. Poultry lacking LA show retarded growth and reduced disease resistance. Intestinal barrier function plays an important role in pigeon squab growth, whereas research on the effects of LA on intestinal health in altrices is scant. Considering that squabs are fed by their parents, the study aimed to explore the effects of maternal dietary LA on intestinal morphology, tight junction proteins, immune cytokines and microbial flora in squabs. A completely randomised design with a control group, 1 % LA supplementation group, 2 % LA supplementation group and 4 % LA supplementation group was used. Six squabs from each treatment were randomly sampled at 21 d post-hatching. The results indicated that LA supplementation improved intestinal morphology, as reflected by increased villus height, villus area and the ratio of villi to crypts. Also, 1 % LA supplementation elevated the density of goblet cells in the intestine and strengthened tight junctions by up-regulating claudin-3 and occludin gene expression but down-regulating claudin-2 gene expression. Moreover, 1 % LA supplementation reduced the secretion of proinflammatory cytokines and partly increased anti-inflammatory cytokines. The intestinal microbial diversity in the 1 % LA supplementation group was higher than that in the other groups. As beneficial bacteria, Butyrivibrio was the biomarker of 1 % LA supplementation. However, excessive (4 %) LA supplementation led to adverse impacts on intestinal immunity and microbiota. In conclusion, maternal dietary LA might alter intestinal barrier function in pigeon squabs in a dose-dependent manner. Supplementation with 1 % LA was suggested in parental pigeons.

Shifts in the maternal gut microbiota have been implicated in the development of gestational diabetes mellitus (GDM). Understanding the interaction between gut microbiota and host glucose metabolism will provide a new target of prediction and treatment. In this nested case-control study, we aimed to investigate the causal effects of gut microbiota from GDM patients on the glucose metabolism of germ-free (GF) mice. Stool and peripheral blood samples, as well as clinical information, were collected from 45 GDM patients and 45 healthy controls (matched by age and prepregnancy body mass index (BMI)) in the first and second trimester. Gut microbiota profiles were explored by next-generation sequencing of the 16S rRNA gene, and inflammatory factors in peripheral blood were analyzed by enzyme-linked immunosorbent assay. Fecal samples from GDM and non-GDM donors were transferred to GF mice. The gut microbiota of women with GDM showed reduced richness, specifically decreased Bacteroides and Akkermansia, as well as increased Faecalibacterium. The relative abundance of Akkermansia was negatively associated with blood glucose levels, and the relative abundance of Faecalibacterium was positively related to inflammatory factor concentrations. The transfer of fecal microbiota from GDM and non-GDM donors to GF mice resulted in different gut microbiota colonization patterns, and hyperglycemia was induced in mice that received GDM donor microbiota. These results suggested that the shifting pattern of gut microbiota in GDM patients contributed to disease pathogenesis.

The present study aimed to evaluate the status of iodine nutrition and thyroid function in adults, to understand the distribution of thyroid disease in people with autoimmune thyroid disease (AITD) in different water iodine areas and to explore the relationship between serum iodine, urine iodine and thyroid function in people with AITD. A cross-sectional survey was conducted in areas of Shandong Province with different water iodine levels, and subsequently 1225 adults were enrolled from iodine-deficient (ID), iodine-adequate (IA) and iodine-excess (IE) areas. Urinary iodine, water iodine, salt iodine, serum iodine and thyroid function were measured. According to the urine iodine concentration, the ID and IA areas were defined as iodine sufficient and the IE area as iodine excessive. Urine iodine, serum iodine, free thyroxine (FT4) and thyroid-stimulating hormone (TSH) levels were comparatively higher in the IE area. The positive rate of thyroglobulin antibody (19·1 %) and the prevalence of AITD (21·8 %) were higher in the ID areas; the prevalence of subclinical hypothyroidism was lowest in the ID areas (7·3 %) and highest in the IE area (16·3 %). Among the AITD population, urinary iodine concentration, free triiodothyronine, FT4 and TSH had a non-linear correlation with serum iodine; abnormal TSH level, serum iodine concentration > 110 µg/l and goitre were risk factors for AITD in adults, especially females. Our data collectively suggest that universal salt iodisation has improved the iodine nutritional status of the population in ID areas in China. Non-step-by-step iodine fortification may induce the transformation of thyroid autoimmune diseases from recessive-to-dominant in susceptible people. Moreover, enhanced monitoring of thyroid function in people with AITD is important.

In this paper, we report the recent progress on the $1~\text{PW}/0.1~\text{Hz}$ laser beamline of Shanghai Superintense Ultrafast Laser Facility (SULF). The SULF-1 PW laser beamline is based on the double chirped pulse amplification (CPA) scheme, which can generate laser pulses of 50.8 J at 0.1 Hz after the final amplifier; the shot-to-shot energy fluctuation of the amplified pulse is as low as 1.2% (std). After compression, the pulse duration of 29.6 fs is achieved, which can support a maximal peak power of 1 PW. The contrast ratio at $-80~\text{ps}$ before main pulse is measured to be $2.5\times 10^{-11}$. The focused peak intensity is improved by optimizing the angular dispersion in the grating compressor. The maximal focused peak intensity can reach $2.7\times 10^{19}~\text{W}/\text{cm}^{2}$ even with an $f/26.5$ off-axis parabolic mirror. The horizontal and vertical angular pointing fluctuations in 1 h are measured to be 1.89 and $2.45~\unicode[STIX]{x03BC}\text{rad}$, respectively. The moderate repetition rate and the good stability are desirable characteristics for laser–matter interactions. The SULF-1 PW laser beamline is now in the phase of commissioning, and preliminary experiments of particle acceleration and secondary radiation under 300–400 TW/0.1 Hz laser condition have been implemented. The progress on the experiments and the daily stable operation of the laser demonstrate the availability of the SULF-1 PW beamline.

The second home-made single stage accelerator mass spectrometer (SSAMS) system dedicated to radiocarbon (14C) measurements was built after the first SSAMS system was moved to Guangxi Normal University. With some improvements to the second SSAMS system, the performance has been improved. With the conditions of total ion energy of 200KeV, ions charge states of 1+ and helium as stripper gas, 14C measurements with precision of 0.5% and a background level of 0.5 pMC were achieved. Details of the system and the experimental performance are given here.

The average power of diode-pumped fiber lasers has been developed deeply into the kW regime in the past years. However, stimulated Raman scattering (SRS) is still a major factor limiting the further power scaling. Here, we have demonstrated the mitigation of SRS in kilowatt-level diode-pumped fiber amplifiers using a chirped and tilted fiber Bragg grating (CTFBG) for the first time. The CTFBG is designed and inscribed in large-mode-area (LMA) fibers, matching with the operating wavelength of the fiber amplifier. With the CTFBG inserted between the seed laser and the amplifier stage, an SRS suppression ratio of ${\sim}10~\text{dB}$ is achieved in spectrum at the maximum output laser power of 2.35 kW, and there is no reduction in laser slope efficiency and degradation in beam quality. This work proves the feasibility and practicability of CTFBGs for SRS suppression in high-power fiber lasers, which is very useful for the further power scaling.

Soil conservation on the Loess Plateau is important not only for local residents but also for reducing sediment downstream in the Yellow River. In this paper, we report a decrease in soil erosion from 2000 to 2010 as a result of the ‘Grain for Green' (GFG) Project. By using the Revised Universal Soil Loss Equation and data on land cover, climate and sediment yield, we found that soil erosion decreased from 6579.55tkm–2yr–1 in 2000 to 1986.66tkm–2yr–1 in 2010. During this period, there was a major land cover change from farmland to grassland in response to the GFG. The area of low vegetation coverage with severe erosion decreased dramatically, whereas the area of high vegetation coverage with slight erosion increased. Our study demonstrates that the reduction in soil erosion on the Loess Plateau contributed to the decrease in the sediment concentration in the Yellow River.