One of the fundamental challenges in understanding the early stages of corrosion pitting in metals protected with an oxide film is that there are relatively few techniques that can probe microstructure with sufficient resolution while maintaining a wet environment. Here, we demonstrate that microstructural changes in Al thin films caused by aqueous NaCl solutions of varying chloride concentrations can be directly observed using a liquid flow cell enclosed within a transmission electron microscope (TEM) holder. In the absence of chloride, Al thin films did not exhibit significant corrosion when immersed in de-ionized water for 2 days. However, introducing 0.01 M NaCl solutions led to extensive random formation of blisters over the sample surface, while 0.1 M NaCl solutions formed anomalous structures that were larger than the typical grain size. Immersion in 1.0 M NaCl solutions led to fractal corrosion consistent with previously reported studies of Al thin films using optical microscopy. These results show the potential of in situ liquid cell electron microscopy for probing the processes that take place before the onset of pitting and for correlating pit locations with the underlying microstructure of the material.

Energy resolution is one of the most important parameters in electron energy-loss spectroscopy. This is especially true for measurement of surface plasmon resonances, where high-energy resolution is crucial for resolving individual resonance peaks, in particular close to the zero-loss peak. In this work, we improve the energy resolution of electron energy-loss spectra of surface plasmon resonances, acquired with a monochromated beam in a scanning transmission electron microscope, by the use of the Richardson–Lucy deconvolution algorithm. We test the performance of the algorithm in a simulated spectrum and then apply it to experimental energy-loss spectra of a lithographically patterned silver nanorod. By reduction of the point spread function of the spectrum, we are able to identify low-energy surface plasmon peaks in spectra, more localized features, and higher contrast in surface plasmon energy-filtered maps. Thanks to the combination of a monochromated beam and the Richardson–Lucy algorithm, we improve the effective resolution down to 30 meV, and evidence of success up to 10 meV resolution for losses below 1 eV. We also propose, implement, and test two methods to limit the number of iterations in the algorithm. The first method is based on noise measurement and analysis, while in the second we monitor the change of slope in the deconvolved spectrum.

Carbon nanotubes (CNT) have proven to be materials with great potential for the construction of biosensors. Development of fast, simple, and low cost biosensors to follow reactions in bioprocesses, or to detect food contaminants such as toxins, chemical compounds, and microorganisms, is presently an important research topic. This report includes microscopy and spectroscopy to characterize raw and chemically modified multiwall carbon nanotubes (MWCNTs) synthesized by chemical vapor deposition with the intention of using them as the active transducer in bioprocessing sensors. MWCNT were simultaneously purified and functionalized by an acid mixture involving HNO3–H2SO4 and amyloglucosidase attached onto the chemically modified MWCNT surface. A 49.0% decrease in its enzymatic activity was observed. Raw, purified, and enzyme-modified MWCNTs were analyzed by scanning and transmission electron microscopy and Raman and X-ray photoelectron spectroscopy. These studies confirmed purification and functionalization of the CNTs. Finally, cyclic voltammetry electrochemistry was used for electrical characterization of CNTs, which showed promising results that can be useful for construction of electrochemical biosensors applied to biological areas.

Focused ion beam is a powerful method for cross-sectional transmission electron microscope sample preparation due to being site specific and not limited to certain materials. It has, however, been difficult to apply to many nanostructured materials as they are prone to damage due to extending from the surface. Here we show methods for focused ion beam sample preparation for transmission electron microscopy analysis of such materials, demonstrated on GaAs–GaInP core shell nanowires. We use polymer resin as support and protection and are able to produce cross-sections both perpendicular to and parallel with the substrate surface with minimal damage. Consequently, nanowires grown perpendicular to the substrates could be imaged both in plan and side view, including the nanowire–substrate interface in the latter case. Using the methods presented here we could analyze the faceting and homogeneity of hundreds of adjacent nanowires in a single lamella.

Atom probe is a powerful technique for studying the composition of nano-precipitates, but their morphology within the reconstructed data is distorted due to the so-called local magnification effect. A new technique has been developed to mitigate this limitation by characterizing the distribution of the surrounding matrix atoms, rather than those contained within the nano-precipitates themselves. A comprehensive chemical analysis enables further information on size and chemistry to be obtained. The method enables new insight into the morphology and chemistry of niobium carbonitride nano-precipitates within ferrite for a series of Nb-microalloyed ultra-thin cast strip steels. The results are supported by complementary high-resolution transmission electron microscopy.

To date, it is unclear whether chemical order (or disorder) is in any way connected to double exchange, electronic phase separation, or charge ordering (CO) in manganites. In this work, we carry out an atomic resolution study of the colossal magnetoresistant manganite La2−2xSr1+2xMn2O7 (LSMO). We combine aberration-corrected electron microscopy and spectroscopy with spectroscopic image simulations, to analyze cation ordering at the atomic scale in real space in a number of LSMO single crystals. We compare three different compositions within the phase diagram: a ferromagnetic metallic material (x=0.36), an insulating, antiferromagnetic charge ordered (AF-CO) compound (x=0.5), which also exhibits orbital ordering, and an additional AF sample (x=0.56). Detailed image simulations are essential to accurately quantify the degree of chemical ordering of these samples. We find a significant degree of long-range chemical ordering in all cases, which increases in the AF-CO range. However, the degree of ordering is never complete nor can it explain the strongly correlated underlying ordering phenomena. Our results show that chemical ordering over distinct crystallographic sites is not needed for electronic ordering phenomena to appear in manganites, and cannot by itself explain the complex electronic behavior of LSMO.

High-throughput immuno-electron microscopy is required to capture the protein–protein interactions realizing physiological functions. Atmospheric scanning electron microscopy (ASEM) allows in situ correlative light and electron microscopy of samples in liquid in an open atmospheric environment. Cells are cultured in a few milliliters of medium directly in the ASEM dish, which can be coated and transferred to an incubator as required. Here, cells were imaged by optical or fluorescence microscopy, and at high resolution by gold-labeled immuno-ASEM, sometimes with additional metal staining. Axonal partitioning of neurons was correlated with specific cytoskeletal structures, including microtubules, using primary-culture neurons from wild type Drosophila, and the involvement of ankyrin in the formation of the intra-axonal segmentation boundary was studied using neurons from an ankyrin-deficient mutant. Rubella virus replication producing anti-double-stranded RNA was captured at the host cell’s plasma membrane. Fas receptosome formation was associated with clathrin internalization near the surface of primitive endoderm cells. Positively charged Nanogold clearly revealed the cell outlines of primitive endoderm cells, and the cell division of lactic acid bacteria. Based on these experiments, ASEM promises to allow the study of protein interactions in various complexes in a natural environment of aqueous liquid in the near future.

Early embryonic heart development is a period of dynamic growth and remodeling, with rapid changes occurring at the tissue, cell, and subcellular levels. A detailed understanding of the events that establish the components of the heart wall has been hampered by a lack of methodologies for three-dimensional (3D), high-resolution imaging. Focused ion beam scanning electron microscopy (FIB-SEM) is a novel technology for imaging 3D tissue volumes at the subcellular level. FIB-SEM alternates between imaging the block face with a scanning electron beam and milling away thin sections of tissue with a FIB, allowing for collection and analysis of 3D data. FIB-SEM was used to image the three layers of the day 4 chicken embryo heart: myocardium, cardiac jelly, and endocardium. Individual images obtained with FIB-SEM were comparable in quality and resolution to those obtained with transmission electron microscopy. Up to 1,100 serial images were obtained in 4 nm increments at 4.88 nm resolution, and image stacks were aligned to create volumes 800–1,500 μm3 in size. Segmentation of organelles revealed their organization and distinct volume fractions between cardiac wall layers. We conclude that FIB-SEM is a powerful modality for 3D subcellular imaging of the embryonic heart wall.

A microcompressor is a precision mechanical device that flattens and immobilizes living cells and small organisms for optical microscopy, allowing enhanced visualization of sub-cellular structures and organelles. We have developed an easily fabricated device, which can be equipped with microfluidics, permitting the addition of media or chemicals during observation. This device can be used on both upright and inverted microscopes. The apparatus permits micrometer precision flattening for nondestructive immobilization of specimens as small as a bacterium, while also accommodating larger specimens, such as Caenorhabditis elegans, for long-term observations. The compressor mount is removable and allows easy specimen addition and recovery for later observation. Several customized specimen beds can be incorporated into the base. To demonstrate the capabilities of the device, we have imaged numerous cellular events in several protozoan species, in yeast cells, and in Drosophila melanogaster embryos. We have been able to document previously unreported events, and also perform photobleaching experiments, in conjugating Tetrahymena thermophila.

A microstructural characterization study was performed on high-pressure die cast specimens extracted from escalator steps manufactured from an Al-12 wt.% Si alloy designed for structural applications. Black and white, color light optical imaging and scanning electron microscopy techniques were used to conduct the microstructural analysis. Most regions in the samples studied contained globular-rosette primary α-Al grains surrounded by an Al-Si eutectic aggregate, while primary dendritic α-Al grains were present in the surface layer. This dendritic microstructure was observed in the regions where the melt did not impinge directly on the die surface during cavity filling. Consequently, microstructures in the surface layer were nonuniform. Utilizing physical metallurgy principles, these results were analyzed in terms of the applied pressure and filling velocity during high-pressure die casting. The effects of these parameters on solidification at different locations of the casting are discussed.

The dehydrogenated microstructure of the lithium borohydride-yttrium hydride (LiBH4-YH3) composite obtained at 350°C under 0.3 MPa of hydrogen and static vacuum was investigated by transmission electron microscopy combined with a focused ion beam technique. The dehydrogenation reaction between LiBH4 and YH3 into LiH and YB4 takes place under 0.3 MPa of hydrogen, which produces YB4 nano-crystallites that are uniformly distributed in the LiH matrix. This microstructural feature seems to be beneficial for rehydrogenation of the dehydrogenation products. On the other hand, the dehydrogenation process is incomplete under static vacuum, leading to the unreacted microstructure, where YH3 and YH2 crystallites are embedded in LiBH4 matrix. High resolution imaging confirmed the presence of crystalline B resulting from the self-decomposition of LiBH4. However, Li2B12H12, which is assumed to be present in the LiBH4 matrix, was not clearly observed.

We report the analysis of the changes in local carbon structure and chemistry caused by the self-implantation of carbon into diamond via electron energy-loss spectroscopy (EELS) plasmon energy shifts and core-edge fine structure fingerprinting. These two very different EELS energy and intensity ranges of the spectrum can be acquired under identical experimental conditions and nearly simultaneously using specially designed deflectors and energy offset devices known as “DualEELS.” In this way, it is possible to take full advantage of the unique and complementary information that is present in the low- and core-loss regions of the EELS spectrum. We find that self-implanted carbon under the implantation conditions used for the material investigated in this paper creates an amorphous region with significant sp2 content that varies across the interface.

The vasa vasorum (VV) of explanted segments of the human great saphenous vein (Vena saphena magna; HGSV), harvested during dissection for coronary bypass grafts or diseased vein segments from the “Salzburger Landesklinikum,” were studied by scanning electron microscopy and three-dimensional morphometry of microvascular corrosion casts. The main objective of this study was to examine the VV’s structural arrangement in order to find the most vital segments of the HGSV and in turn to improve the results of coronary bypass surgeries. The study presents a meticulous analysis of the whole microvascular system of the VV of the HGSV and its three-dimensional arrangement. It is one of the first studies yielding detailed quantitative data on geometry of the VV of the HGSV. A detailed insight into different vascular parameters such as vessel diameter, interbranching, intervascular distances, and branching angles at different levels of the VV’s angioarchitecture and in different parts of the HGSV in health and disease is given. Further, the geometry of bifurcations was examined in order to compute the physiological optimality principles of this delicate vascular system based on its construction, maintenance, and function.

A contactless method of probing and analyzing multifunctional oxide interfaces using an electron energy analyzer inside a scanning electron microscope is presented. High contrast experimental secondary electron analyzer signals are used to detect changes in the interface conductivity of a LaAlO3/SrTiO3 sample. Monte Carlo simulations of the primary beam/specimen interaction are carried out and correlated with the experimental results in order to help understand the role of the primary beam energy and adjust it to enhance contrast.