Medical imaging is of great importance for patients affected by stroke. Since an early examination of the patient is necessary for successful recovery, there is room to improve the existing capabilities of analysis. Common systems like magnetic resonance imaging or computed tomography are precise, but stationary, and therefore, not ideally suited for the early analysis of stroke. The presented multiport vector network analyzer system uses electromagnetic tomography (EMT) as an alternative imaging technique. It consists of a network of distributed electronic sensor nodes which improve important parameters: the parallel measurement setup reduces the measurement time as low as 160 ms for a 200-port S-parameter matrix and it is capable of measuring signal levels down to − 150 dBm. The electronics allow a compact, movable packaging, leading the way for future portable devices. The detection of stroke models was examined by test measurements of a phantom. The data was analyzed by the help of an inverse reconstruction algorithm. The possibility of building portable setups which can be even applied to patients inside an ambulance, makes EMT a suitable alternative for early stroke detection. It can help in shortening the recovery of patients, by providing an early analysis of the brain.

In recent years, millimeter wave (MMW) has received tremendous interest among researchers, which offers systems with high data rate communication, portability, and finer resolution. The design of the antenna at MMWs is challenging as it suffers from fabrication and measurement complexities due to associated smaller dimensions. Current state-of-the-art MMW dual-band antenna techniques demand high precision fabrication, which increases the overall cost of the system. Henceforth, the design of an MMW antenna with fabrication and measurement simplicity is quite challenging. In this paper, a simple coplanar waveguide (CPW) fed single-band MMW antenna operating at 94 GHz (W band) and a dual-band MMW antenna operating concurrently at 60 GHz (V band) and 86 GHz (E band) have been designed, fabricated, and measured. A 50 Ω CPW-to-microstrip transition has also been designed to facilitate probe measurement compatibility and to provide proper feeding to the antenna. The fabricated single frequency 94 GHz antenna shows a fractional bandwidth of 11.2% and E-plane (H-plane) gain 6.17 dBi (6.2 dBi). Furthermore, the designed MMW dual-band antenna shows fractional bandwidth: 2/6.4%, and E-plane (H-plane) gain: 7.29 dBi (7.36 dBi)/8.73 dBi (8.68 dBi) at 60/86 GHz, respectively. The proposed antenna provides a simple and cost-effective solution for different MMW applications.

Synthesis of non-uniform circular antenna arrays using a hybrid invasive weed optimization is introduced in this paper. The excitation weights and positions of array elements are optimized to reduce the peak side lobe level (PSLL) of the radiation pattern. The method proposed in this paper can effectively constrain the number of the array elements, size of the array, and the angular spacing of the adjacent element simultaneously. The radiation pattern has the constraint of a fixed major lobe beamwidth. Synthesis results of three different circular antenna arrays are given. The results show the effectiveness and feasibility of the proposed synthesis method in non-uniform circular antenna arrays.

A new structure of Q-band filter comprising rectangular high-permittivity dielectric resonators (DR) operating at TM11δ mode is introduced. The resonator shows high-quality factor (Q) and wide spurious free window compared with other technologies available at Q-band for realizing filters. Low permittivity ceramic material (quartz) is used as a support for holding DR at the center of the cavity. An eight-pole cross-coupled band-pass filter having a bandwidth of 225 MHz at 38.5 GHz was realized. Resonant coupling structure is introduced to realize cross-coupling in filter. The resonator assemblies were optimized precisely to achieve effective linear frequency drift over temperature of the order of 2 ppm/°C. The filter also survived severe sine and random vibration test for satellite application.

A quad band antenna with good gain and omni-directional pattern is proposed in this paper. The antenna design is based on loading a conventional monopole antenna by three different resonators. The resonators are inspired from the shunt branch of composite right-/left-handed cell. The resonators have a simple structure and compact size. The control of the frequency bands can be achieved arbitrarily and hence the suggested design methodology can be generalized to any required bands. The fabricated antenna prototype is operating at 2.6, 3.35, 5.15, and 6.1 GHz with bandwidth wider than 100 MHz for each band. The antenna's operating principle and design procedures with the aid of electromagnetic full wave simulation are presented. Finally, the experimental results exhibit good agreement with the simulated ones which confirm the proposed designed methodology. The proposed monopole antenna has a patch size of 13.5 mm × 6.5 mm and the whole antenna size (including the feed line) is 35 mm × 32 mm. Compared to conventional single-band microstrip patch radiator size, the proposed quad band radiator has the size of 9, 15, 37.5, and 72.5% at relevant frequency bands.

In this paper, a dual-wideband bandpass filter (BPF) with independently controllable center frequencies (CFs) and wide stopband suppression is presented using a new quintuple-mode resonator (QMR). By applying the classical odd-/even-mode analysis method, the resonant characteristics of the new QMR have been analyzed. It shows that five modes can be excited, and two of them can be employed to form the lower passband, while the other three modes contribute to the higher passband. For verification, a dual-wideband BPF using the new QMR is designed, fabricated, and tested. Experimental results show that the CFs of the dual-wideband BPF centered at 2.96 GHz and 5.695 GHz with 3 dB fractional bandwidths of 27.7 and 23.4%, respectively. In addition, 20-dB suppression in upper-stopband ranges from 2.23 to 4.04f0, where f0 is the center frequency of the first passband. The measurement results are in good agreement with the prediction results.

This paper proposes, a high gain, Fabry Perot cavity antenna with coplanar waveguide (CPW) fed ultra wide band (UWB) radiating element. The proposed antenna has flat edge arrow shape-based radiating element, which act as a main radiating element and responsible for UWB radiation. This UWB microstrip antenna is parasitically coupled with an array of square parasitic patches (PPs), which act as partially reflective surface. The square patches are fabricated at the bottom of inexpensive FR4 substrate and suspended in the air with the help of dielectric rods at 1.5λ0 height. High gain is obtained by resonating PPs at near close frequencies of 3.8–8.8 GHz UWB, where partially reflective surface gives almost positive reflection phase gradients. Two laboratory prototypes of antenna, one with and another without partially reflective surface are fabricated and tested. Details of the proposed antenna design and role of partially reflective surface in gain enhancement of planar CPW fed UWB antenna are described, and typical experimental results are presented and discussed.

This paper aims at investigating the dependence of the impedance and the radiation characteristics of a cylindrical dielectric resonator antenna (DRA), on the feed point of the DRA. It is demonstrated that the resonant frequency, bandwidth, radiation pattern symmetry, and cross-polarized radiation levels depend highly on the feed point. Three standard single-ended feed mechanisms such as the microstrip line, the microstrip slot, and the coaxial probe are taken as examples, to demonstrate the feed-point dependence of the DRA performance. Standard commercial EM simulation tools (ANSYS HFSS and CST Microwave Studio) are used for generating insightful results to help the discussion. This analysis also provides a functional comparison among the above said three feed mechanisms with respect to the feed-point dependence, which is further verified through measurements of DRA prototypes employing the three feeds.

An impulse response method is carried out to analyze waveguide's information capacity within a coherent communication system. Such capability is typically estimated according to group delay variations (seconds/bandwidth/distance) after carrier-modulated data undergoes a dispersive medium. However, traditional group delay methods often ignore non-linear effects by assuming input data stream only occupies narrow bandwidth such that a propagation constant can be linearized centered at the carrier frequency. Such a constraint can be lifted with a proposed baseband equivalent impulse response method by using frequency domain convolution and multiplication. Once the impulse response in frequency domain is secured, its time domain counterpart can be calculated based on inverse Fourier transformation. Such analysis can fully reveal data pulse's broadening and gauge its inter-symbol interference by simply convolving input data with extracted impulse response, not limited to specific frequency range or type of waveguide.

Millimeter-wave (mm-wave) beam-steering antennas are preferred for reducing the disruptive effects, such as those caused by high atmospheric debilitation in wireless communications systems. In this work, a compact broadband antenna array with a low loss feed network design is introduced. To overcome the short-range effects on mm-wave frequencies, a feed network – with a modified Butler matrix and a compact zeroth-order resonance antenna element – has been designed. Furthermore, the aperture feed technique has been utilized to provide a broadside stable pattern and improve the delivered gain. A Fabry-Perot layer without the height of the air layer is used. Taking advantage of this novel design, a broadband and compact beam-steering array antenna – capable of covering impedance bandwidths (from 33.84 to 36.59 GHz) and scanning a solid angle of about ~94°, with a peak gain of 17.6 dBi – is attained.

In this work, an UWB/narrow band reconfigurable elliptical-shaped monopole antenna for cognitive radio applications with sequential perception and operation modes is presented. The proposed approach consists in integrating a reconfigurable filter, in an UWB antenna ground plan, by the mean of four horizontal slots and integrated switches that allow inserting/removing/varying zeros and poles in the frequency response. By acting on the slot lengths in order to alter their resonance frequencies, the different switch configurations allow the antenna to switch between an UWB mode that could be used for the perception (sensing) and different narrowband modes, mono-band and dual-band, that could be used for the operation at 2.4 or/and 3.5 GHz. To validate the concept, an experimental prototype has been fabricated and a good agreement between the simulated and the measured S-parameters has been obtained. While the presented work uses the presence/absence of a perfect conductive strip (PEC) to model real switch operation, it is believed that the obtained results conjugated with previous work using real switches on a very similar structure allows validating approach.

A new band-reject frequency-selective surface (FSS) based on dual-band near-zero refractive index metamaterial (ZIM) design is presented in this paper. Consisting of a planar array of complementary dual-layer symmetry resonant ring, the proposed FSS exhibits a high-selective band-reject filtering response. From the viewpoint of effective medium, the subwavelength FSS is characterized by near-zero effective magnetic permeability and near-zero effective electric permittivity in two different operational bands, respectively. The corresponding resonant behavior and E-field distributions are analyzed in detail. A prototype of the proposed FSS working in X-band is fabricated and measured. The simulation and experiment results verify the effectiveness and correctness of the ZIM-based design method.

A compact and planar broadband circularly polarized (CP) eighth-mode substrate integrated waveguide (EMSIW) antenna is proposed in this paper. An isosceles right triangular waveguide with one electric sidewall (located on one of its catheti) and two magnetic sidewalls (located on the other two edges of the triangle) is presented to investigate the characteristics of the EMSIW. The closed-form mode solutions of the electromagnetic field components and the cut-off frequencies are derived for all propagating modes in this triangular waveguide. The simulated electromagnetic field distribution is consistent with the analytical results. The resonant frequencies of the EMSIW cavity are then determined. A CP antenna consisting of four EMSIW elements is designed, fabricated, and measured. The measured 3-dB axial ratio bandwidth of the antenna is 21.6% from 4.72 to 5.86 GHz. Within this frequency range, the measured reflection coefficient is below −10 dB, and the measured peak gain in circular polarization at broadside is 6.89 dBic at 5.1 GHz.

In this paper, a new miniaturized frequency agile filter-antenna with a wide reconfigurable frequency band is proposed for interweave cognitive radios (CRs). A tunable bandpass filter (BPF) composed of a symmetrical ring resonator is cascaded to the feed line of an ultra-wideband planar antenna. The structure of the proposed ring resonator BPF is simple and compact so that the total size of the proposed filter-antenna is smaller than that of a conventional system made of a separate antenna and BPF. The reconfigurability of the proposed filter-antenna is achieved by changing the operating frequency of the BPF by loading the ring resonator with a single varactor diode at its center. The fabricated prototype has successfully achieved a wide operational bandwidth of 1.43 GHz which covers continuous narrow bands from 4.65 to 6.08 GHz. Moreover, the operating tunable narrow bands have stable radiation characteristics. Good agreement between measurement and simulation results is demonstrated.

In this paper, the resonant frequencies, quality factors and bandwidths of high Tc superconducting circular microstrip patches in the presence of a dielectric superstrate loading have been studied using Galerkin testing procedure in the Hankel transform domain. The exact Green's function of the grounded dielectric slab is used to derive an electric field integral equation for the unknown current distribution on the circular disc. Thus, surface waves, as well as space wave radiation, are included in the formulation. London's equations and the two-fluid model of Gorter and Casimir are used in the calculation of the complex surface impedance of the superconducting circular disc. Galerkin testing is used in the resolution of the electric field integral equation. Two solutions using two different basis sets to expand the unknown disk currents are developed. The first set of basis functions used is the complete set of transverse magnetic and transverse electric modes of a cylindrical cavity with magnetic side walls. The second set of basis functions used employ Chebyshev polynomials and enforce the current edge condition. The computed values for a wide range of variations of superstrate thickness and dielectric constant are compared with different theoretical and experimental values available in the open literature, showing close agreement. Results are showing that the superstrate parameters should always be kept into account in the design stage of the superconducting microstrip resonators.

This paper provides an overview of theory, design, simulation, and fabrication of novel spatial harmonic magnetrons (SHMs). An approximate analysis which provides the guidelines for the design and predicts the important characteristics of these devices will be presented. This analysis shows that the metamaterial loaded SHMs can start generating power with very small cathode current densities which is very important for designing THz sources based on SHMs. A design example with the operation frequency of 43 GHz together with the design procedure, PIC simulations, and measurement results will be examined.

A novel shape penta-band microstrip patch antenna is presented in this paper. The proposed antenna shows five operating frequencies and can be used for various wireless applications, i.e. 2.58 GHz for non-direct line of sight, wireless Internet service providers, and compatible with Navini Networks; 3.17 and 3.42 GHz for WiMAX; 4 GHz for C-band application such as weather radar systems; and 5.3 GHz for higher WLAN. Very small frequency ratios of the values 1.2286, 1.078, 1.169, and 1.325 are achieved between two consecutive resonant frequencies. Antenna design techniques for achieving five bands are presented and discussed step by step. The analysis is done by Ansoft HFSS v.15, and results are verified with experimental results of fabricated prototypes.

Jamming of synthetic aperture radar (SAR) is more difficult than the conventional radars because of its high processing gain. The defocusing of fake or virtual scatterers is the main problem that any jamming technique needs to tackle. An algorithm based on fractional Fourier transform is proposed for the efficient jamming of SAR. The results show that the performance of proposed algorithm is better than conventional Range Doppler Algorithm.

This work addresses the piezoelectric induced reduction of quality factor in fully-printed metal-insulator-metal (MIM) barium strontium titanate (BST) thick film varactors designed for high power operation. An acoustically optimized varactor design is presented and compared to a non-optimized high-power varactor. The design is utilized to present a narrowband acoustic suppression technique based on defined weights. The acoustically optimized varactor consists of 162 varactor cells in a capacitive matrix. The cells in the matrix are interconnectable allowing for a variable unbiased capacitance and power rating. Due to this setup, surface acoustic waves are interrupted, and the reduced size of the cells allows for a reduced BST layer thickness, shifting the acoustic resonance away from the operational frequency. Therefore, an inverted behavior in comparison to the high-power varactor is observed with an increasing quality factor with biasing voltage. Compared to the high-power varactor, the acoustically optimized varactor design shows a 40% increased quality factor in biased state. By applying the narrowband acoustic suppression technique, an increase in quality factor of 145% is achieved compared to the unsuppressed design. In comparison to the high-power varactor, the acoustical suppressed design shows an increase in quality factor of 480% at the first acoustic resonance frequency.