In this paper, a new design approach for the six-port (SP) junction is introduced. The proposed design includes a generalized broadband matching and smooth miniaturization scheme and is extendable for any passive multiport structure. A multilayer technology and a microstrip to slot coupling operation are employed for the designed SP, which comprises power divider and three hybrid couplers. The conducted measurements of the constructed SP junctions validates the design approach. Optimal performance of the SP network in terms of miniaturization, bandwidth, and response accuracy were obtained for the 5G low band.

With the increasing demand for smarter antenna design in advanced technology applications, well-designed antennas have been an important factor in enhancing system performance. Most traditional antenna design requires multiple iterations and extensive testing to produce a final product. Machine learning (ML) algorithms have been used as an alternative to predict the optimal design parameters, but the outcome depends highly on the ML model efficiency. With recent development in machine learning algorithms and the availability of data for antenna design, we investigated different machine learning algorithms for optimizing the output strength of three basic antennae by analyzing the signal strength of the antenna for various antenna parameters. Different regression-based ML models were used to learn the behaviors and efficiency of three different antennas and to predict the output strength (S11) for different ranges of frequencies. The experiment compared and analyzed these ML regression algorithms for three different antennas: shot antenna, patch antenna, and bowtie antenna. In addition, the paper also provides comparison of ensemble ML models for performance analysis using the best three ML algorithms from the preliminary study. This study optimizes antenna parameters and quicker and smarter antenna design procedure using ML algorithms as compared to traditional design methods.

Due to increasingly complex and automated manufacturing processes, the demands on the control parameters of these processes are also increasing. One parameter is the fill quantity of, e.g., liquids in production plants, whose precise determination is of ever-growing importance. Up to now, the exact level of determination under difficult conditions, such as high ambient temperatures, has been a particular challenge. This paper demonstrates a novel method by which an M-sequence UWB radar can determine levels of low-permittivity materials in small metal containers. For this purpose, hot melt is used as an example. Thus, the influence of large temperature differences on the long-term stability of level measurement can also be investigated. The measurements show that the level of hot melt can be measured to be long-term stable with an accuracy of better than 3 mm. Furthermore, the precise determination of the empty state is highly important for many applications. For this reason, this paper shows a method for determining the empty state without complex calibration procedures. For the empty level indication, an accuracy of up to 0.5 mm could be achieved for molten hot glue and 3% of the tank volume, independent of the shape or aggregate state of the medium.

Attaching a wireless transmission system comprising a radio frequency (RF)-chip and a dipole antenna to dielectric material of largely different permittivity leads to strong variation of the antenna feed impedance. Due to the severe impedance mismatch between the RF-chip and the antenna, the performance of the system may deteriorate drastically. The proposed antenna provides three feed points, which show respective feed-point match to 100 Ohm balanced feeds for three different dielectric environments (free-space and half-spaces of permittivity 4 and 42, respectively). Thereby, the RF-chip incorporates three 100 Ohm balanced output ports that are connected to the antenna from whom only one can be selected to provide the output signal. The respective other two output ports are shorted by an internal switching circuit that is controlled by external DC voltages. The measurement of the reflection coefficient of the stand-alone antenna and the chip agree well with the simulations, allowing to interconnect these two components. Further, the radiation pattern of the whole system is measured for two different scenarios showing good functionalities.

A simple process for the design of broadband planar antennas is presented for base station applications. The process is based on a square patch above a ground plane. Only three geometric parameters are involved in the design of a dual-polarized broadband planar antenna, including the width (Ws) of the square patch, a trimming angle (θ) of the square, and the height (H) of the patch above the ground plane. By adjusting the critical parameters θ and H, an impedance bandwidth of 50% for return loss (RL) >15 dB is achieved with an isolation of higher than 35 dB. The bandwidth of the broadband planar antenna is enhanced to 67% by etching four Γ slots on the square patch. The operating mechanisms of these broadband antennas are analyzed and verified by simulation and experiment.

Worldwide adoption of fourth-generation wireless (4G) long-term evolution (LTE) smartphones and the actual transition to fifth-generation wireless(5G) is the main driving engine for semiconductor industry. 5G is expected to reach high data rate speeds (1 Gbps) and low latency (<1 ms). 5G requires more RF bandwidth and therefore an increase in the number of components such as RF switches, acoustic filters, and power amplifiers integrated in few RF front-end modules. Also, there is an increase in the number of RF radio transmitters and receivers operating at the same time. This paper presents new architecture elements for 5G RF front-end modules. Circuit details and measurements are presented to reduce the RF noise, improve the efficiency, and help the coexistence of multiple radio transmitters. These circuits will help extend the 5G applications with radar-like sensing applications, remote medicine, and autonomous driving.

This paper describes the design and implementation of a 39 GHz 256-element hybrid active phased array antenna system with 16 individual digital transceivers, and its wireless multi-user, multi-input, multi-output verification. An earlier version of this paper was presented at the 2021 51st European Microwave Conference and was published in its Proceedings [1]. Using the prototype device, a single carrier transmission test assuming a mobile backhaul link and a MU-MIMO transmission test using a zero-forced orthogonal multi-beam based on channel reciprocity assuming an access link was performed. As a result, an EIRP of 43 dBm and a data rate of 5.5 Gbps in 1 GHz bandwidth single carrier 128QAM operation and an estimated total throughput of 2.4 Gbps by 3GPP TS38.214 [2] in 100 MHz bandwidth OFDM 8 MU-MIMO operation were achieved, respectively. As far as the author knows, this is the first demonstration for integrated access and backhaul (IAB) application that uses the 39 GHz band.

Due to their periodic nature, metasurfaces used to perform anomalous reflection raise parasitic harmonic reflections. We show a classical synthesis example of such a structure and highlight its limitations. Floquet analysis and its associated simulation environment are exploited to understand the origin of these parasitic reflections and to mitigate them. The proposed method is based on the optimization of the metasurface periodic pattern: the supercell. A predictive method is built to calculate radar cross-section patterns from supercell Floquet simulation, avoiding dealing with heavy simulations. The proposed model, the optimization outputs, and the general results are exposed in details. Different cases are also discussed to prove the repeatability of the proposed method. An earlier version of this paper was presented at the European Microwave Conference and was published in its proceedings.

This contribution presents miniaturization techniques for folded circular substrate integrated waveguide (FCSIW) cavity filters. The cavities support dual-mode operation. Two of these cavities are combined to form a fourth-order filter. Two filter designs are implemented. The first one serves as a reference and exhibits good manufacturability. For the second one, the cavity is modified, which leads to $50\%$ more compactness. The designs are experimentally verified with 10 GHz bandpass filters. Even though the achieved level of compactness requires higher technological effort, the measurements validate the miniaturization concept. The out-of-band rejection exceeds 40 dB between 11.2 and 30 GHz for the reference filter and between 11.3 and 33 GHz for the miniaturized one. The implemented components are compared with state-of-the-art filters.

Metamaterial lenses are appealing thin alternatives to conventional dielectric lenses. In this contribution we describe their design and application in two exemplary 77 GHz automotive radar sensors operating in monostatic and bistatic modes. The frontends are built around commercially available MMICs and small feed antennas are used in coordination with the six-layer printed circuit board-based realizations of metamaterial lenses. The design follows the principles of dielectric lenses, while the required local phase shift is obtained from a set of metasurface bandpasses. Their design uses a novel interpolation procedure to extract layout parameters for a given phase shift. Despite the small structural sizes due to the high frequency, the fabricated frequency-selective surfaces show very good performance in the required frequency range. Verification measurements were conducted on single bandpasses as well as on metamaterial lenses mounted on the radar frontend. The results agree very well with the simulation and confirm the applicability of thin lenses operating at mm-wave frequencies for automotive radar applications.

This paper describes the experimental investigation of orthogonal time-frequency space (OTFS) modulation using a 28 GHz multi-user distributed multiple-input multiple-output (D-MIMO) testbed in over-the-air (OTA) and mobility environments to enhance cell throughput in a millimeter-wave band. We build the D-MIMO testbed having newly developed OTFS modulator and demodulator, and measured OTFS signals and orthogonal frequency-division multiplexing (OFDM) signals with up to four user simultaneous connections on an actual office floor. Additionally, the Doppler effect on OTFS signals is mathematically analyzed and is confirmed in the measurements. OTFS indicates higher robustness in time-variant channels than OFDM. The error vector magnitude (EVM) and system throughput of OTFS are −22 dB and 1.9 Gbps with 100 MHz signal bandwidth, respectively. To our knowledge, this is a first paper describing the OTA measurements of EVM, throughput, and spectral efficiency using OTFS modulation on the 28 GHz coherent beamforming system.

We report on the development of a handheld three-dimensional (3D) terahertz scanning system with an aspherical telecentric 3D-printed f-θ lens using selective laser sintering. The lens covers a broader scan line of 50 mm with its larger aperture, compared to the 20 mm range in our initial work, which was presented at the European Microwave Week 2021. In order to evaluate the adaptability of the optomechanical components with different sensor units, two different integrated frequency-modulated continuous wave radar modules based on monolithic microwave integrated circuit technology, operating in W- and D-bands are tested within the measurement scheme. The optomechanical part consists of a galvanometer scanner mirror and the f-θ lens. The optical system enables B-scans perpendicular to the manual translational movement of the sensor unit by its user. An integrated guiding wheel system with rotary encoder makes it possible to correlate the measurement points to their respective locations, enabling complete 3D volumetric inspection of the corresponding structures, which is particularly useful for the inspection along cracks and welds.

This paper presents the design, manufacturing, and measurement of a novel substrate integrated waveguide (SIW) pedestal filtering antenna solution for use in 5G New Radio sub-6 GHz communications. Miniaturization is achieved through the use of SIW pedestal resonators and integration of the radiating element into the filter design, resulting in higher order suppression. The design generates a third order filtering response utilizing SIW pedestal resonators and a patch antenna element. The manufactured SIW pedestal filtenna achieves a 10 dB return loss bandwidth of 4.29% about a center frequency of 3.63 GHz, and a boresight gain of 3.66 dBi. Using the SIW pedestal filtenna elements, two array configurations are measured, a 1 × 1 linear array and 2 × 2 planar array. Beam-steering capability for the linear array is demonstrated in simulation, while the 2 × 2 array is shown to be suited to both dual- and single-mode operation.

A high image rejection 38 GHz demodulator in TSMC 65-nm CMOS process is presented. To achieve better than −40 dBc image rejection ratio (IRR), a low I/Q mismatch 45° LO power splitter of sub-harmonic mixer is proposed. In this design, the 45° LO power splitter is composed of a Wilkinson divider, a series delay line with electrical length of 45° on one side of the divider, and a shunt 90° transmission line on the other side. This configuration is attractive because of its design simplicity and easy fabrication. Compared with the conventional techniques that utilize capacitors and inductors instead of the shunt 90° transmission line, the proposed LO power splitter can alleviate the issue of process variation. The demodulator demonstrates an IRR lower than −40 dBc from 37.5 to 41.5 GHz. In addition, conversion gain is 1.3 ± 0.9 dB from 33 to 41 GHz with 6 dBm LO power. The total direct current power consumption is 78 mW from 1.0 V supply voltage. At the modulation scheme of 4096-QAM, the proposed demodulator demonstrates 1.7% (−35.1 dB) error vector magnitude (EVM), which is very close to the EVM measurement floor 1.6% (−36 dB) of our millimeter-wave signal analyzer.

Digital radar waveforms such as orthogonal frequency-division multiplexing (OFDM) often have the disadvantage that they require high sampling rates if fine range resolutions have to be achieved. The frequency comb OFDM radar scheme offers a possibility to overcome this drawback and to improve the range resolution without increasing the sampling rate. Simultaneously, the high unambiguous velocity, which is one of the advantages of digital radar waveforms, is retained and due to the simple generation of orthogonal transmit signals, it is well suited for multiple-input multiple-output (MIMO) applications. To prove all these features of the frequency comb OFDM radar scheme, a suitable 4 × 4 MIMO demonstrator including frequency comb generation as well as up- and downconversion with these combs has been set up. Its functionality has been validated with real measurements in an anechoic chamber in conjunction with a radar target simulator to emulate very high velocities.

This work introduces a method for plasma state supervision, based on a frequency-modulated continuous wave radar sensor and a suitable signal evaluation enabling a continuous supervision method for the plasma state. Highly precise phase evaluation of the signal allows us to detect and visualize smallest changes in the plasma state. Assuming the plasma to act like a frequency-dependent dielectric material, the propagation of the electromagnetic wave depends on the plasma state and hence, also the measured phase. Broadband measurements are carried out at center frequencies of 80 and 140 GHz in a low-pressure plasma. The radar-based setup can be used for a very flexible application, capable for spatially resolved measurements in the plasma bulk. At the same time, the high measurement rate allows for quasi real-time monitoring, so that transient processes in the plasma are recorded. Due to the simple setup, this approach is most suitable for industrial applications to improve process control. The chosen different frequencies will show a change in the influence of the plasma on the electromagnetic wave demonstrating the advantages of multi-frequency approaches in future applications.

Short-channel Gallium Nitride (GaN) high-electron-mobility transistors (HEMTs) often utilize T-shape gates due to their large gate-line cross-sectional area and subsequent fMAX increase. In this paper, we report the linearity trade-offs associated with varying the T-gate geometries of AlGaN/GaN HEMTs on Si, specifically the gate extensions which serve as field plates and their impact on the large-signal performance. Small-signal characterization and modeling, in addition to TCAD, provide initial guidelines for the optimal dimensions for the gate field plates using the ratio of fT and the product of the gate resistance and the gate-to-drain capacitance. We utilize various characterization methods, including 6 GHz non-linear vector network analyzer characterization in addition to load-pull, to quantify the amplitude and phase distortion and their subsequent impact on the large-signal metrics of the devices under differing matching conditions and bias points. We deduce that the influence of the gate field plates on the amplitude and phase distortion is non-negligible, particularly under matched conditions.

A dual-band dual-linearly polarized waveguide slot array antenna is proposed in this paper. Two orthogonal slots share a short-circuit wall on broad side. The horizontal and vertical slots, which actualize dual-frequency bands and dual-linear polarization, generate vertically polarized electric fields in 9.39–9.78 GHz and horizontally polarized electric fields in 11.62–12.3 GHz, respectively. The equivalent permittivity of the waveguide is changed by two grooves at the bottom of the waveguide, which improves phase velocity. Two grooves can also reduce the distance between the elements while suppressing the side lobes. Compared to filling the medium in the waveguide, two grooves have less losses. Moreover, the antenna is simple with one input port. The array antenna also overcomes the problems of beam scanning compared with the traditional waveguide slot array antenna. A 1 × 8 antenna array is fabricated and measured to verify the design. The horizontal polarization is formed in 9.39–9.78 GHz, the vertical polarization is generated in 11.62–12.3 GHz, and the antenna gain can reach 15 dBi.