A variety of related questions is posed. Are the right priorities for future aircraft design being set now? New civil aircraft types could be ‘silent’, i.e. make much less noise than current types. They could be ‘green’, i.e. safeguard the environment. Is silent as important as Green? The crucial answer is that future aircraft design should focus on substantial reductions on climate change impact. The air quality targets proposed by the ‘Sustainable Aviation’ initiative appear very ambitious: they should be pursued only to the extent that they do not affect improved fuel efficiency and reduced climate-changing emissions. Good progress has already been made on the aircraft noise targets proposed by the ‘Sustainable Aviation’ initiative, but again they should be pursued only to the extent that they do not affect improved fuel efficiency and reduced climate-changing emissions. The financial case for designing to reduce aircraft noise in order to deliver novel financial benefits, e.g. increase airport flights at night and/or relocate airports, is weak.

The stall and immediately post-stall behaviour of a microlight aeroplane are shown to be a function of the deceleration rate prior to the stall; therefore, it is necessary to use a representative deceleration rate when determining the acceptability of stall and post-stall handling qualities. This research has found means by which the range of deceleration rates likely to be seen in a particular type can be estimated, so that flight test programmes can ensure these rates are included, and thus aircraft are confirmed to have acceptable stalling characteristics. Recommendations are made towards the use of this research for all aircraft type, and of further work which might usefully be carried out.

Human factors certification criteria are being developed for large civil aircraft with the objective of reducing the incidence of design-induced error on the flight deck. Many formal error identification techniques currently exist which have been developed in non-aviation contexts but none have been validated for use to this end. This paper describes a new human error identification technique (HET – human error template) designed specifically as a diagnostic tool for the identification of design-induced error on the flight deck. HET is benchmarked against three existing techniques (SHERPA – systematic human error reduction and prediction approach; human error HAZOP – hazard and operability study; and HEIST – human error In systems tool). HET outperforms all three existing techniques in a validation study comparing predicted errors to actual errors reported during an approach and landing task in a modern, highly automated commercial aircraft. It is concluded that HET should provide a useful tool as a adjunct to the proposed human factors certification process.

Minimum drag shapes of given length and base area are investigated for hypersonic flow using both Newtonian impact theory and free molecular flow theory. The drag of Newton’s minimum drag body, which has previously been evaluated by numerical means, is derived as an analytic expression. The analytical results are applicable to a range of local pressure laws allowing minimum drag shapes obtained using impact theory to be directly compared with low density flow equivalents using free molecular flow. The low density shapes are found to have larger blunt regions at the nose and significantly larger drag coefficients. For free molecular flow the drag varies with the surface reflection characteristics. As the fraction of diffuse reflection at the surface increases, the drag increases and the sensitivity of the drag to changes in the minimum drag shape is reduced.

The use of unmanned aerial vehicles (UAVs) in various military and civil applications is the subject of much current attention. With recent developments in personal computer technology, and the availability at affordable cost of peripherals, and electronic and optical sensors, UAVs for long endurance missions, with flight autonomy beyond the visual range, have become an attractive challenge for study in universities and research institutes. This paper describes the development of a target-lock-on optical remote sensing system to be used as a payload in a university-class UAV. To accomplish autonomous way-point navigation for the conduct of optical sensing surveillance, a gimbaled-platform with servo control and an Attitude and Heading Reference System (AHRS) navigation system for UAV position and attitude measurements have been developed. The UAV also utilises a Global Position System (GPS) receiver, a pressure altimeter, gyroscopes and an electric compass. A novel mathematical model is proposed to calculate the optimal parameters for orientating the CCD camera line of sight with a ground target, designated in real time from a ground control station. Both ground and flight test results have demonstrated the feasibility of the navigation control scheme and the UAV’s ability to conduct ground target acquisition and image transmission.

It is considered that the blended wing body may offer the possibility of improvements in performance efficiency over the conventional civil transport. Such configurations will require transonic wind tunnel testing. Hence, a feasibility study has been carried out at ARA to investigate possible model support systems that could be used for this purpose. The study addressed issues arising from the mechanical design of two support systems; namely, a blade or Z-sting and a standard rear sting. In particular, the relatively restricted space available within the model fuselage has presented challenges in the design of the layout of the balance and instrumentation required for the model. CFD analysis has been carried out to assess the relative interference effects of the two support arrangements. This initial work has shown unexpectedly significant interference effects associated with the Z-sting support and attention is drawn to the need for further design work to minimise these effects.

This paper describes the development of a wind turbulence criterion for the safe operation of helicopters to offshore installations. The development of the criterion was recommended following a review of the environmental effects around offshore platform helidecks.

Currently, criteria exist for ambient temperature and for vertical wind component in the vicinity of helidecks, but a questionnaire-based survey of helicopter pilots revealed that the principal safety hazard and source of highest workload is turbulence around offshore installations. The new turbulence criterion will plug a long-standing gap in the guidance on offshore helideck design.

The paper describes how the criterion has been developed using piloted flight simulation in a research flight simulator together with data from wind tunnel tests on offshore platforms. Initial validation has been successfully performed, and extended to include correlation with the large database of helicopter operational flight data records being collected through the UK North Sea Helicopter Operations Monitoring Programme (HOMP).

The turbulence criterion will be used, together with existing criteria on vertical wind component and temperature, in the assessment of new offshore installation designs, or proposed modifications to existing designs, to determine wind conditions where turbulence is likely to be excessive for safe helicopter operations. These will be used to estimate helideck operability and thereby inform the installation topsides design process, and will provide input to the setting and maintenance of helicopter operational limitations for individual installations.

The work will lead to improved safety through better prediction of safe operating envelopes and helideck operability at the design stage. In addition, development of the work is expected to enable the wind environment around offshore installations to be mapped and monitored in-service using helicopter flight data records.

The new turbulence criterion has been included in updated guidance on helideck design, and offshore installation designers are now required to inform helicopter operators about wind conditions which result in violations of the turbulence criterion on their offshore installations (as is currently the case for the temperature and vertical wind component criteria).

Experimental studies often use several blades, joined on the centreline, to generate a vortex in a wind tunnel. The circulation profile of this vortex is non-trivial, and a rapid prediction method will facilitate the design of such devices. Prompted by an experiment of Beninati and Marshall, such a model was derived. It assumes a large number of narrow blades and small turning angles, and rests on a balance of angular momentum and on simple aerofoil function. It is claimed to be valid even close to the centreline, can be completed analytically, contains no adjustable constants, and agrees well with two experiments although the turning angle reached 16° and the devices only had two or four blades. With typical geometries, the interference between blades makes the circulation profile quite different from that behind an elliptically-loaded wing, prompting some doubt over the relevance of such a vortex to those trailing real wings.

A new approach for low-drag high-lift system design based on the application of viscous flow solvers was developed in the EC research project EPISTLE. Two high-lift systems for a supersonic commercial transport aircraft (SCT) wing were designed, manufactured and wind-tunnel tested. The predicted large drag reductions were fully confirmed by tests at high Reynolds numbers. These drag reductions significantly reduce the low-speed noise of future SCT configurations. This was estimated by preliminary aircraft design tools. Low-speed noise reduction by aerodynamic means is obtained, as effective high-lift systems enable these aircraft to climb faster.

Multidisciplinary design and innovative highly automated manufacturing methods are increasingly important to today’s aircraft industry: multidis-ciplinary design because it reduces lead-time and results in a better design, and automated manufacturing methods because they are more capable and reduce manufacturing cost. In this paper a cost estimation model is presented that integrates the manufacturing cost of friction stir welded connections within a multidisciplinary design decision tool. Due to the fact that friction stir welding is a new manufacturing method, the cost estimation model is based on the actual process physics, meaning what the process looks like in terms of processing speeds and characteristics. As an integral part of a multidisciplinary design framework, the developed cost estimation model contributes to a design support tool that assesses not only manufacturing but also structural and aerodynamic issues. It is shown that the cost model developed can be integrated into this more holistic design process support architecture. The predicted costs are accurate to the historical data and allow tradeoff of manufacturing and economic considerations within the context of the multidisciplinary design tool. The tradeoff capability is highlighted through a presented case study that compares the friction stir welding process as an alternative solution to more tradition riveting. Most importantly, this results in a quantitative tradeoff between two processes that shows the manufacturing cycle time of friction stir welding to be reduced by 60% and the recurring assembly cost by 20%.

This paper applies existing information on solar storms to unmanned aviation; no new research data is presented. The purpose of this paper is to alert the unmanned aviation community to the potential hazards posed by solar storms, to familiarise it with the effects of solar storms and how to mitigate them, and to encourage research on solar storm effects on high altitude long endurance (HALE) aircraft and airship design and operations. As unmanned aircraft and airships move increasingly into high altitude (50,000+ft), endurance (24+ hr) roles, they will become vulnerable to the effects of space weather, specifically that of solar storms. Although solar storms are commonly associated with their impact on satellites, they affect the routing and timing of airline flights flying for six to eight hours at 30,000 to 40,000ft. Operating twice as high and with flight times twice as long (or longer) than those of airliners, HALE aircraft and airships occupy a middle zone of vulnerability, being more so than airliners but less so than satellites. A key difference however is that satellites are designed for space weather, whereas some current HALE vehicles are not. The paper concludes that unmanned HALE aircraft and airships can be one to three orders of magnitude more vulnerable to solar storms than a trans-Pacific airliner.

The conditions for thermally-induced buckling of an unloaded thin, circular disk are compared from two well-known but unconnected studies: an approximate solution by Freund for a constant thickness disk, which must neglect the free edge condition, and an exact solution by Mansfield but only for a disk whose thickness tapers to zero in a particular manner. It is shown that buckling occurs at slightly higher values compared to a finite element analysis of a constant thickness disk but that the case of variable thickness seems to offer a closer result, which suggests that it better models the boundary layer behaviour near the free edge.

A complete system engineering process is applied to a pilot project that will determine the initial deployment of the system engineering process for future projects. It was a challenge to complete the entire systems engineering process to include project team utilisation of system engineering tools in such a short time span. Therefore, systems engineering products had to be useful and productive to the project. The system requirements definition, quality function deployment (QFD) evaluation, trade study, risk identification and risk mitigation processes were completed in a timely manner and assisted in the system eequirements, system design and preliminary design reviews successfully.

A system of systems study plan was developed and a prototype was executed to optimise a recommended military force structure. This methodology defined the optimal force structure, using constrained optimisation to reflect budget limitations and desired mission performance. The force structure included surface and air assets, a command, control, communications, computers, intelligence, surveillance and reconnaissance (C4ISR) architecture, and a recommended logistics infrastructure. A second aspect of the study plan defined the total acquisition strategy, which accounted for: retiring legacy assets, extending the service life of existing assets until new replacements became available, and acquiring new assets for deployment, within the budget allocation. This methodology combined various modeling and simulation techniques to meet three study objectives. First, a nonlinear mixed integer programming model maximised performance, subject to cost constraints, cost as an independent variable (CAIV). Second, a dynamic programming model scheduled the transition from the legacy force structure to the future force, defined by the previous modeling technique. Third, a process simulation model simulated performance, over a one-year time period, for 25 areas of responsibility and five missions. This model verified performance estimates generated by the previous models.

Computational fluid dynamics models range from the finite difference type grid-based method to the Lagrangian style vortex cloud simulation technique for solving the Navier-Stokes equations. This paper undertakes a comparison of these two methods for the classical datum bluff body case of flow past a stationary circular cylinder at low Reynolds numbers in the range 10 to 220. Comparisons include time-history, time-mean and root-mean-square values of oscillating drag and lift coefficients, frequency of vortex shedding and related vortex street wake flow patterns. Particularly close agreement was obtained for Strouhal number versus Reynolds number, and good agreement for time-mean value of drag coefficients; comparison was also made with experimental results. Attempts are also made to calculate the skin friction and surface pressure components of the cylinder drag, revealing the significance of skin friction drag within this range and its relative insignificance above a Reynolds number of 220.

The main objective of the paper is to evaluate the potential of reducing the environmental impact of civil subsonic aviation by using hydrogen fuel. The paper is divided into three parts of which this is Part I, where the background, prospects and Challenges of introducing an alternative fuel in aviation are outlined. In Part II the aero engine design when using hydrogen is covered, and in Part III the subjects of optimum cruising altitude and airport implications of introducing liquid hydrogen-fuelled aircraft are raised.

Looking at the prospect of alternative fuels, synthetic kerosene produced from biomass turns out to be feasible and offers environmental benefits in the short run, whereas hydrogen seems to be the more attractive alternative in the long run.

Powering aero engines and aircraft with hydrogen has been done successfully on a number of occasions in the past. Realising this technology change for a fleet of aircraft poses formidable challenges regarding technical development, energy requirement for producing hydrogen, handling, aircraft design and making liquid hydrogen economically compatible with kerosene.

The results of an investigation into the effects that sub-boundary layer vortex generators (SBVGs) have on reducing normal shock-induced turbulent boundary-layer separation are presented. The freestream Mach number and Reynolds number were M = 1·45 and 15·9 × 106/m, respectively. Total pressure profiles, static pressure distributions, surface total pressure distributions, oil flow visualisation and Schlieren photographs were used in the results analysis. The effects of SBVG height, lateral spacing and location upstream of the shock were investigated. A novel curved shape SBVG was also evaluated and comparisons against the conventional flat vane type were made. The results show that in all but two cases, separation was completely eliminated. As expected, the largest SBVGs with height, h = 55%δ, provided the greatest pressure recovery and maximum mixing. However, the shock pressure rise was highest for this case. The experiments showed that the mid height SBVG array with the largest spacing provided similar results to the SBVG array with the largest height. Reducing the distance to shock to 10δ upstream also showed some improvement over the SBVG position of 18δ upstream. It was suggested that total elimination of the separated region may not be required to achieve a balance of improved static pressure recovery whilst minimising the pressure rise through the shock. The effect of curving the SBVGs provided an improved near wall mixing with an improved static and surface total pressure recovery downstream of the separation line. The optimum SBVG for the current flow conditions was found to be the curved vanes of h = 40%δ, with the largest spacing, located at 18δ upstream of the shock. Overall, it was apparent from the results that in comparison to larger vortex generators with a height comparable to δ, for SBVGs the parameters involved become more important in order to obtain the highest degree of mixing from a given SBVG configuration.

Presented in this paper are the prerequisite steps in a methodology for the identification and assessment of unit cost drivers for use in the development of a new design-oriented unit cost estimation methodology for large commercial jet aircraft with minimum seating capacity of 100 passengers. The work presented here focuses on unit cost, which is a significant element of the total aircraft cost and for the initial aircraft design process in particular. The methodology aims to investigate how aircraft design properties could influence cost. Cost estimation relationships, containing a wide range of the most highly correlated parameters, are retrieved from detailed regression analysis conducted on two different aircraft generation categories. Since the methodology is based on actual cost and technical data, it is accurate both in terms of predicting the aircraft unit cost or conducting cost-comparative studies between different aircraft concepts. The emphasis in this paper is mainly on the development approach and parameter assessments, adopted towards the final unit cost estimation methodology.

The integration of multidisciplinary data is key to supporting decisions during the development of aerospace products. Multidimensional metamodels can be automatically constructed using limited experimental or numerical data, including data from heterogeneous sources. Recent progress in multidimensional response surface technology, for example, provides the ability to interpolate between sparse data points in a multidimensional parameter space. These analytical representations act as surrogates that are based on and complement higher fidelity models and/or experiments, and can include technical data from multiple fidelity levels and multiple disciplines. Most importantly, these representations can be constructed on-the-fly and are cumulatively enriched as more data become available. The purpose of the present paper is to highlight applications of these cumulative global metamodels (CGM), their ease of construction, and the role they can play in aerospace integration. A simple metamodel implementation based on a radial basis function network is presented. This model generalises multidimensional data while simultaneously furnishing an estimate of the uncertainty on the prediction. Four examples are discussed. The first two illustrate the efficiency of surrogate-based design/optimisation. The third applies CGM concepts to a data fusion application. The last example is used to visualise extrapolation uncertainty, based on computational fluid dynamics data.