Heterogeneous magnesium matrix nanocomposites (Hetero-Mg-NCs) exhibited excellent strength–toughness synergy, but their damage behavior and toughness mechanism lacked of investigation. Here, atomic force microscopy was first employed to characterize the microstructure evolution and damage behavior of the Hetero-Mg-NCs after indentation. The heterogeneous structure comprised of pure Mg areas (soft phase) and Mg nanocomposite areas (hard phase) was revealed by the electrostatic force microscopy. Furthermore, the surface morphology and cracks of the deformed area were investigated with high resolution. The results indicated the soft phase undertook most of the deformation and played an important role in capturing and blunting the crack.

The interaction between negatively charged all-inorganic silicon quantum dots (Si QDs) and bovine serum albumin (BSA) is studied. It is shown that a small difference in the size of Si QDs affects the structure of Si QD–BSA composites significantly. When the diameter of Si QDs is 4 nm, a heterodimer (~20 nm) composed of one Si QD and one BSA molecule is a preferable and stable structure. On the other hand, when the diameter is 7 nm, the size of the composites increases to ~50 nm. The Si QD–BSA composites exhibit stable photoluminescence in the near-infrared range in phosphate-buffered saline.

Osteoporosis is a skeletal disease characterized by bone loss and bone microarchitectural deterioration. The combination of smart materials and stem cells represents a new therapeutic approach. In the present study, highly porous scaffolds are prepared by combining the conducting polymer PEDOT:PSS with collagen type I, the most abundant protein in bone. The inclusion of collagen proves to be an effective way to modulate their mechanical properties and it induces an increase in scaffolds’ electrochemical impedance. The biomimetic scaffolds support neural crest-derived stem cell osteogenic differentiation, with no need for scaffold pre-conditioning contrarily to other reports.

Sinnerite (Cu6As4S9) is a semiconductor computed to have attractive optoelectronic properties, but little attention has been paid to its experimental synthesis and characterization. Here, the authors report the first synthesis of polycrystalline sinnerite thin films. By heating Cu3AsS4 nanoparticles in sealed ampoules with As2S2 powder, a phase transformation to Cu6As4S9 is achieved along with the formation of micron-sized dense grains appropriate for device applications. The films display a bandgap of ~1.2 eV, significant photocurrent generation under simulated AM1.5 illumination, and carrier lifetimes nearing 1 ns, demonstrating the promise of sinnerite for use in photovoltaic applications.

To improve the stability of Cs2SnCl6 under aqueous/moisture environments, we applied a concept of artificial passivation by depositing a protective TiO2 coating of 10 nm on the surface of Cs2SnCl6. Static leaching experiments results indicate that the initial release rates of Cs+ and Cl− are decreased by 20–30 times with TiO2 coating, suggesting its possibility to improve the short-term water/environmental stability of Cs2SnCl6. An amorphous-to-crystalline phase transition in TiO2 film was observed, possibly resulting in degradation of Cs2SnCl6. However, the crystalline TiO2 film still remains after 21 days water exposure and can still act as an effective passivation layer to reduce the release rates of Cs+ and Cl- by as much as about 17 and 7 times, respectively, relative to static leaching without artificial coatings. Therefore, the water/environmental stability of metal halide perovskite Cs2SnCl6, which is a highly soluble molecular salt, can be enhanced by the nanoscale TiO2 coating as an artificial passivation film.

The narrow bandgap of Ag2S quantum dots was used to decorate TiO2 nanotube arrays (TiO2 NTAs) by the successive ionic layer adsorption and reaction (SILAR) method to enhance its photoelectrochemical performance. The micromorphology of the photoanode films prepared by the SILAR under different parameters (including different cycle times, capillary spot sample, and ultrasound-assisted) was systematically analyzed. The photoanode film Ag2S/TiO2 prepared by the SILAR under the ultrasound-assisted method shows Ag2S evenly distributed in TiO2 NTAs. At the same time, the corresponding photoabsorption range has been extended to the visible area, while the photocurrent density and photoconversion efficiency have been increased to ~1.8 mA/cm2 and 0.6%, respectively.

Thermal transport of pillared-graphene structure (PGS) supported on a copper substrate was investigated using equilibrium molecular dynamics. The results show that thermal conductivity along the graphene sheet in Cu-supported PGS ranges between 96.12 and 247.16 W/m K for systems with different dimensions at an interaction strength χ = 1. Thermal conductivity along carbon nanotube was found to range between 22.43 and 30.83 W/m K. The increase of interaction strength between Cu and carbon leads to a general decrease in thermal conductivity of PGS. The simulation results suggest that the thermal conductivity in Cu-supported PGS systems is governed by system geometry and phonon transport.