Stiffened wing and fuselage panels often have a postbuckling reserve of strength, enabling them to carry loads far in excess of their critical buckling loads. Therefore allowing for postbuckling in design can reduce their weight, hence reducing fuel consumption and environmental impact. The present paper extends the postbuckling analysis in the exact strip software VICONOPT to more accurately reflect the skewed mode shapes arising from shear load and anisotropy. Such mode shapes are represented by a series of sinusoidal responses with different half-wavelengths which are coupled together using Lagrangian multipliers to enforce the boundary conditions. In postbuckling analysis the in-plane deflections involve responses with additional half-wavelengths which are absent from the out-of-plane deflection series. Numerical results are presented and compared with finite element analysis for validation. The present analysis gives close results compared to the finite element and finite strip methods and saves computational time significantly.

Route planning and airspace sectorisation are two central tasks in air traffic management. Traditionally, the routing and sectorisation problems were considered separately, with aircraft trajectories serving as input to the sectorisation problem and, reciprocally, sectors being part of the input to the path finding algorithms.

In this paper we propose a simultaneous design of routes and sectors for a transition airspace. We compare two approaches for this integrated design: one based on mixed integer programming, and one Voronoi-based model that separates potential “hotspots” of controller activity resulting from the terminal routes.

We apply our two approaches to the design of Stockholm Terminal Maneuvering Area.

An important prerequisite for the design, assessment and certification of aircraft and their associated control systems is a quantitative specification of the environment in which the aircraft is intended to operate, for example, atmospheric gust. Gust loads on aircraft may induce detrimental influences such as increased aerodynamic and structural loads, structural deformation and decreased flight dynamic performance. This paper presents a systematic and comprehensive overview of important concepts and applications of gust loads on aircraft. This overview includes a brief research background, concepts, research techniques, influences and load alleviation measures of gust. Finally, we summarise some potential improvements in the future work. It is also recommended to learn from previous experiences to avoid aviation accidents due to flight through atmospheric gusts and turbulence.

Hypersonic air-breathing propulsion can improve cost and flexibility of Low Earth Orbit (LEO) satellite launch missions. However, at the high flight Mach numbers required for access-to-space, performance margins are extremely tight. Techniques to improve mixing efficiency can push this technology forward. However, these are required to produce a minimal increase in losses and heat loads to be viable. The use of inlet-generated vortices in scramjets for mixing enhancement was previously studied. These vortices interact with the injected fuel plume, stretching it and increasing its effective surface for mixing. Moreover, these vortices are intrinsic to the flowfield. Therefore, contrary to other methods, when using inlet vortices mixing is enhanced without producing additional heat loads or losses. This work studies the vortex-injection interaction through numerical RANS simulations. A non-dimensional variable defining the quality of the plume shape for mixing purposes is proposed. This parameter is used to assess the effect of vortex intensity and injector location on fuel plume shape. The results show the ability of inlet vortices to modify fuel plume shape significantly increasing fuel mixing rate with minimal impact on losses.

With the aims of overcoming the limitations of the existing basic flow model derived from an axisymmetric generating body and extending the aerodynamic design method of the airframe/inlet integrated waverider vehicle, this study develops an upgraded basic flow model derived from an axisymmetric shock wave. It then upgrades the design method for airframe/inlet integration of an air-breathing hypersonic waverider vehicle, which is termed the ‘full-waverider vehicle’ in this study. In this paper, first, the design principle and method for the upgraded full-waverider vehicle derived from an axisymmetric basic shock wave are described in detail. Second, an upgraded basic flow model that accounts for both internal and external flows is derived from an axisymmetric basic shock wave by use of both the streamline tracing method and the method of characteristics (MOC). Third, the upgraded full-waverider vehicle is developed from the upgraded basic flow model by the streamline tracing method. Fourth, the design theories and methodologies of both the upgraded basic flow model and the upgraded full-waverider vehicle are validated by a numerical computation method. Finally, the aerodynamic performances and viscous effects of both the upgraded basic flow model and the upgraded full-waverider vehicle are analysed by numerical computation. The obtained results show that the upgraded basic flow model and aerodynamic design method are effective for the design of the airframe/inlet integration of an air-breathing hypersonic waverider vehicle.

Steps required for proper acquisition and processing of laser Doppler velocimetry data for turbomachinery research applications are addressed. Turbomachinery applications are difficult due to the small internal passages, high-frequency fluctuations, large turbulence intensities, and strong secondary flows resulting in low overall signal-to-noise ratios and narrowband noise sources that cannot be removed by simple band-pass filters. Special aspects that must be considered for successful and accurate laser Doppler velocimetry studies to be conducted in turbomachinery are discussed. Specifically, the design of the measurement volume size, reflection mitigation, engineering of seed particle size and injection schema, and alignment of the traverse mechanism are addressed in terms of their importance (from literature sources) and the solutions implemented by the authors. These techniques have been applied to successfully obtain three-component, unsteady velocity data in a high-speed centrifugal compressor for aeroengine application. Processing techniques are also presented including a novel mixture-model-based statistical method for narrowband noise isolation developed by the authors. The method, validation steps, and example results are presented, showing the successful rejection of noise with high accuracy, a low failure rate, and a significant reduction in required manual inspection. This newly developed method elucidated flow features that were not clear prior to the noise removal.

Experimental and numerical investigations into the linear and nonlinear aeroelastic behaviour of very flexible High Altitude Long Endurance (HALE) wings are conducted to assess the effect of geometrical nonlinearities on wings displaying moderate-to-large displacement. The study shows that the dynamic behaviour of wings under large deflection, and specifically the edgewise and torsion natural frequencies and modal characteristics, are largely affected by the presence of geometrical nonlinearities. A modular wing structure has been manufactured by rapid prototyping and it has been tested to characterise its dynamic and aeroelastic behaviour. At first, several simple isotropic cantilever beams with selected crosssections are numerically investigated to extract their modal characteristics. Experiments are subsequently conducted to validate the geometrically nonlinear dynamics behaviour due to high tip displacement and to understand the influence of the beam cross-section geometry. The structural dynamics and aeroelastic analysis of a very flexible modular selected wing is then investigated. Clean-wing wind-tunnel tests are carried out to assess flutter and dynamic response. The wind-tunnel model display interesting aeroelastic features including the substantial influence of the wing large deformation on its natural frequencies and modal characteristics.

The aim of this work is to develop a calculation model based on the method of characteristics making it possible to study the effect of the stagnation pressure of the combustion chamber on the 2D and axisymmetric minimum length nozzle design giving a uniform and parallel flow at the exit section. The model is based on the use of the real gas approach. The co-volume and the intermolecular interaction effect are taken into account by the use of the Berthelot state equation. The effect of molecular vibration is considered in our model to evaluate the behaviour of gas at a high temperature. In this case, the stagnation pressure and the stagnation temperature are important parameters in our model. The resolution of the algebraic equations is done by the finite difference corrector predictor algorithm. The validation of the results is controlled by the convergence of the critical section ratios calculated numerically as obtained by the theory. The mass and the thrust are evaluated to improve the efficiency of the nozzle. The comparison is made with the high temperature and perfect gas models. The application is made for air.

The model of Nano quad-rotors contains many uncertainties such as an external disturbance from a wind field, highly non-linear strong coupling between variables and body measurement errors. To deal with these uncertainties and control the Nano quad-rotors, a novel data-based disturbance observer (DO) is firstly proposed to observe disturbances from a wind field and perturbations from errors of parameter estimation. Then the DO is used to improve the conventional dynamic inversion (DI) method to obtain an enhanced dynamic inversion (EDI) method, which relies only on roughly estimated geometrical parameters, thus eliminating the largest flaw of conventional DI, namely depending on detailed plant information. Simulation results show that the method proposed achieved good trajectory tracking with only roughly estimated geometrical values under wind field; the DO proposed can accurately estimate disturbance from a wind field and perturbation from error of parameter estimation.

The takeoff-mass of a two-stage-to-orbit Rocket-Based Combined Cycle Engine-Rocket (RBCC-RKT) launch vehicle is a crucial factor in its comprehensive performance. This paper optimizes the takeoff-mass together with the trajectory by reformulating it to a nonlinear optimal control problem. The range of the second stage rocket mass is considered as a process constraint. When the scopes of initial and terminal states are specified, the problem can be solved by using the Gauss pseudo-spectral method (GPM). In order to reduce the convergent difficulty caused by using table data, the data in different stages are utilized by employing an integrated interpolation strategy through the optimization. Simulation results show that the mass can be effectively optimized to meet the inertia mass ratio constraint of the first-stage, and the separation of Mach number and altitude can be optimized at the same time.

Numerical simulations have been carried out for a 32.16-ft-diameter rotor in autorotational forward flight. Coupled flapping and rotational equations were solved using the transient simulation method (TSM) to ascertain the quasistatic torque equilibrium conditions. The Pitt/Peters inflow theory was adopted in the simulations, and an airfoil look-up table made by a compressible Navier-Stokes solver was used. The adverse cyclic and collective pitch inputs were introduced in a similar fashion to helicopter control in that the cyclic lever is pulled back and the collective lever is pushed down for increasing airspeeds. The simulation results showed that the longitudinal cyclic pitch input combined with a lowered collective pitch increases the rotating torque for a low shaft angle and an advance ratio greater than one, producing both high lift and a high lift-to-drag ratio. Upon introducing the adverse cyclic and collective pitch inputs, the control range broadened, and a torque equilibrium condition was detected at 414.7kt (700ft/s) of airspeed in the simulation.

In order to increase the speed, precision and robustness against the engine failure in solving optimal endo-atmospheric ascent trajectory of a launch vehicle, a rapid multi-layer solving method with improved numerical algorithms was proposed. The proposed method is capable of decomposing a large number of intervals into multiple layers with advantageous convergence property. Firstly, the problem of solving optimal endo-atmospheric ascent trajectory, which was subjected to path constraints and terminal constraints, was transformed into a Hamilton Two Point Boundary Value Problem (TPBVP). Then, through the finite difference method and numerical solving algorithm, the Hamilton TPBVP was iteratively solved with fewer initial discrete intervals. The initial values of higher-layer iterations were obtained by interpolating convergent solutions at sparse nodes into the doubly discrete nodes of high layers. The process was repeatedly performed until the solving precision met the requirements. To decrease the calculation load in solving TPBVPs, two improved solving algorithms without and with fewer Jacobian calculations were studied, respectively the Derivative-free Spectral Algorithm for Nonlinear Equations(DF-SANE) combined with the improved derivative-free nonmonotone line search strategy, and the Modified Newton method with a relaxation factor in combination with the Inverse Broyden Quasi-Newton method, denoted as ‘MN-IBQ’. Simulation verifications showed that the multi-layer method had significantly higher solving speed than the single-layer method. For the improved numerical algorithms, the DF-SANE was trapped in the local convergence problem. While using the proposed MN-IBQ can further increase the solving rate. Typical engine failure simulations showed that the multi-layer method with the MN-IBQ algorithm had not only significantly higher solving speed but also stronger robustness, where the traditional single-layer method could not adapt. In addition, the thrust loss tolerance limits for the multi-layer solving method were given for different engine failure times. The results show promising potential of the proposed approach in trajectory online generation and closed-loop guidance of launch vehicles at the endo-atmospheric ascent stage.

System software subsystems in an unmanned aircraft system share hardware resources due to space, weight, and power constraints. Such subsystems have different criticality, requirements, and failure rates, and can cause undesired interference when sharing the same hardware. A component with high failure rate can reduce the reliability of the system unless a fault containment mechanism is adopted.

This work proposes an asymmetric multiprocessor architecture to establish isolation at the hardware level for distributed implementation of safety-critical subsystems along with user defined payload subsystems on the same hardware with minimally reduced reliability of the system. To achieve that, subsystems are strategically segregated in separate processors, connected to an on-chip protective interconnect for inter-processor communications. A custom watchdog and reset mechanism are implemented to reset a specific processor without affecting the entire system if required. The architecture is demonstrated on a FPGA chip. In addition, an example of an optimised distribution is provided for a specific flight control system with five subsystems.

Predicting mental workload of pilots can provide cockpit designers with useful information to reduce the possibility of pilot error and cost of training, improve the safety and performance of systems, and increase operator satisfaction. We present a theoretical model of mental workload, using information theory, based on review investigations of how effectively task complexity, visual performance, and pilot experience predict mental workload. The validity of the model was confirmed based on data collected from pilot taxiing experiments. Experiments were performed on taxiing tasks in four different scenarios. Results showed that predicted values from the proposed mental workload model were highly correlated to actual mental workload ratings from the experiments. The findings indicate that the proposed mental workload model appears to be effective in the prediction of pilots’ mental workload over time.

Aeronautic Pitot probes (PPs) are extremely important for airspeed and altitude measurements in aviation. Failure of the instrument due to clogging caused by ice formation can lead to dangerous situations. In this work, a commercial aeronautic PP was characterised experimentally regarding its inner composition, material properties and its thermal performance in a climatic wind tunnel. Performance runs were taken out in order to analyse the thermal response of the PP under various operating conditions with a particular emphasis on the cooling process in the case of a heating element failure. Data for the thermal conductivity, diffusivity and specific heat for each material forming the PP were obtained. A numerical model to simulate the thermal behaviour of the PP was created using Comsol Multiphysics (CM). Experimental data were compared with their numerical counterparts for model validation purposes. After the model was validated, the operation of the PP in flight conditions was simulated. The failure of the conventional heating system was analysed to obtain the time until the PP reaches a tip temperature where ice formation can be expected. The tip temperature undercut the zero degrees Celsius mark 165 seconds after the heating element was switched off. The data collected in this work can be used to implement and validate mathematical models in order to predict the thermal performance of Pitot probes in flight conditions.

This paper deals with the actuation system design of a full-scale morphing aileron for regional aircraft. The aileron is allowed to smoothly change its geometrical configuration and perform the in-flight transition from a baseline shape to a set of optimal morphed ones pre-defined on the basis of aerodynamic requirements. The design of such innovative aileron is aimed not only at substituting the conventional aileron installed on a real aircraft but also to provide additional functionality. The aileron is free to rotate around its main hinge axis and it is also allowed to smoothly modify camber with two independent actuation systems. In such manner it can be used also during cruise with a symmetric deflection between the two half wings in order to reduce drag in off design condition. To accomplish variable aileron shape, a rigid-body mechanism was designed. The proposed aileron architecture is characterised by segmented adaptive ribs rigidly linked each other with spanwise reinforcements such as spars and stringers in a multi-box arrangement. Each rib is split into two movable plates connected by means of rotational hinges in a finger-like mechanism. The mechanism is driven by a load-bearing actuator by means of a kinematic chain opportunely tied based on the structural requirements in terms of shape to be matched and load to be withstood. The proposed device is an innovative arrangement of the quick-return mechanism composed of a beam leverage, commercial linear guides and a crank. The actuator shaft is directly inserted in the crank, which transmits the rotation to the linear guide that slide along a rail moving upward or downward the beam thus resulting in a camber variation. The entire aileron is moved by three leverages internally contained and distributed along the first two bays while the most external ribs are considered passive and their movement slaved. Two actuation layouts are analytically and numerically studied, the analytical theory is presented and validated by means of a multi-body simulation. Moreover, a linear static analysis was carried out under the hypothesis of glued contact between linear guides components simulating a jamming condition. This assumption has been formulated because it represents the most severe condition that envelop all the operative loads to which the actuation system is subjected. The analyses conducted are preliminarily aimed to verify that no failure occur under the imposed loads. In this first design loop, the vertical static force acting on the linear carriage exceeded allowable value and then a new configuration with double-sided linear guides was then investigated.

In this paper, we examine some of the physics behind Vertical Take-Off and Landing (VTOL) flying machines, and some of the emerging technologies that are driving the recent upsurge of new VTOL projects. The paper attempts to put these into context by examining some of the projects that have been publicised over the past couple of years, particularly those that transition from hovering into wing-borne flight. Although much progress has been made, there still needs to be significant breakthroughs in technologies, particularly battery technology, before the dream of fast, quiet and environmentally friendly inter-city VTOL aircraft can be realised.