Since the 1980s National Flying Laboratory Centre has used the Jetstream family of aircraft as a flying classroom, providing university students and developing professionals with real-world exposure to theoretical concepts in the form of practical flight test instruction. Recently the Jetstream was replaced with a newer Saab-340B. The work in this paper presents an experimental analysis of instruction using the Jetstream, compared with known best practices, to inform its replacement process. Flight activities were observed, and participating students (n = 60) were surveyed at four set intervals to establish their mood and interest towards the module. A pen and paper test, comparing what participants learned compared to a controlled group was also administered. While the module was still able to excite, motivate and re-contextualise previously taught information to students, upgrades to the aging technology suite, specifically to support data analysis and briefing was one of the greatest needs from the newer aircraft.

To meet the increasing communication demands, the satellites need to be equipped with the high-accuracy and large-aperture antennas. One of the effective methods to construct the modular antennas with ultra-high accuracy and ultra-large aperture is on-orbit assembly technology. During the on-orbit assembly missions, the assembly error is a key factor to affect the surface accuracy of the modular antennas. This paper studies the node design of each module and the assembly error analysis of the modular antennas. A design method of the module nodes is presented with consideration of the assembly gap between two modules. Meanwhile, a soft connection mechanism is designed to ensure the mobility among the assembly modules. To investigate the transmission law of the assembly errors, an analytical model of assembly error is derived based on the exponential product method. In order to establish the deformation surface with rotation and displacement assembly errors, an error ball concept is proposed by the analytical model. To decrease the assembly errors, the actuators are installed among some modules. Moreover, an adjustment method is proposed to obtain the adjustment amounts of actuators. Finally, the correctness of analytical model and the effectiveness of the adjustment method are demonstrated by the numerical simulations.

This paper presents the results of the experimental study carried out to address the issues of base heating and smooth separation of the stage of launch vehicles. The pressure at the base of a convergent-divergent circular nozzle, from which Mach 1.8 jet emanates, attached to an annular shroud of larger area is controlled by providing air vents on the shroud. On the shroud, vent holes were made at different azimuthal locations, to entrain the surrounding air mass at a higher pressure, pa, to increase the low-pressure, pb, at the base region, caused by the suction creating large-scale vortices formed owing to the sudden expansion of the jet emerging from the nozzle into the shroud. For different number and size of the vents on the shroud, the base pressure was measured. This measurement was done at five levels of overexpansion of the nozzle in the range from –64% to –58%. It is found that increase in vent area results in increase of base pressure, up to some limiting level of the area. Also, the increase of base pressure for the case of vents closer to the nozzle exit is found to be marginally more than the increase caused by vents at distances away from the nozzle exit. Increase of base pressure can be regarded as an advantage not only from base heating point of view but also from the point of view of deflection of the plume to the shroud wall for uniform melting of the pyro layer bonding the stages of the launch vehicle, leading to a smooth separation of the launch vehicle stages.

The accuracy of several numerical schemes for solving the lifting-line equation is investigated. Circulation is represented on discrete elements using polynomials of varying degree, and a novel scheme is introduced based on a discontinuous representation that permits arbitrary polynomial degrees to be used. Satisfying the Helmholtz theorems at inter-element boundaries penalises the discontinuities in the circulation distribution, which helps ensure the solution converges towards the correct, continuous behaviour as the number of elements increases. It is found that the singular vorticity at the wing tips drives the leading-order error of the solution. With constant panel widths, numerical schemes exhibit suboptimal accuracy irrespective of the basis degree; however, driving the width of the tip panel to zero at a rate faster than the domain average enables improved accuracy to be recovered for the quadratic-strength elements. In all cases considered, higher-order circulation elements exhibit higher accuracy than their lower-order counterparts for the same total degrees of freedom in the solution. It is also found that the discontinuous quadratic elements are more accurate than their continuous counterparts while also being more flexible for geometric representation.

In January 2017, a business jet flew in Norway on a short repositioning flight with two pilots onboard, no passengers or cargo. Initially, the take-off proceeded as normal but as the landing gear was retracted both pilots observed that the airspeed was rapidly approaching the flap limiting speed of 200kts. When the flaps were fully retracted at a height of approximately 2,100ft above ground level, the crew experienced a violent nose-down pitch motion. Control was regained at a height of approximately 170ft above ground level and, following the accident, data from the flight data recorder showed that the aircraft experienced –2.62G during the pitch upset. A tailplane stall due to icing was suspected; however, the flight data recorder, being limited to 36 parameters, was not able to confirm this. For expediency during the accident investigation process, a simplified, linear flight dynamics model was developed using Matlab/Simulink to assess static and dynamic stability for a range of tailplane efficiency factors to simulate the effects of tailplane icing.

Helicopter collisions with obstacles are one of the most frequent and most devastating causes of accidents. To avoid these collisions in low-speed operations a “haptic ticker” cue in form of repetitive impulses as a force feedback was designed for an active sidestick. Various design questions were examined in pilot campaigns using a full flight simulator and four test scenarios. As a result, the pilots always knew which distance-based hazard area (green, yellow, red) they were in. Furthermore, the ticker is disruptive and roughly reduces the handling qualities from Level 1 to Level 2. It is therefore primarily activated as a hazard warning and not as a main input to control the distance. As a warning cue the ticker was evaluated as non-disturbing. The force threshold to detect the direction of a tick was determined. With tick strengths above this threshold, the direction is still not recognised at all in around 2% of the ticks. For the remaining ticks, the accuracy with which the direction is recognised is about 15°. In the fourth scenario, obstacles were moved towards the hovering helicopter, potentially forcing a collision. However, with the ticker a collision occurred in less than 4% of the cases, instead of 84% without the ticker. The ticker was rated as very intuitive and worth recommending. When asked how many accidents of this kind could be prevented with this ticker, all five pilots independently estimated 75%.

There are many factors causing the shimmy of the aircraft landing gear and structural clearance of landing gear is a typical factor. Some aircraft in service or operation did not shimmy before, but suddenly appeared after a period of use. To solve the problem of clearance shimmy during the service of a certain aircraft, we established a dynamic model of rotating gear with clearance based on the flexible multi-body dynamics model of landing gear and L-N contact theory. We defined different types of clearance and established a mechanical model of aircraft pendulum vibration considering the clearance of landing gear structure for dynamic simulation, and studied the effects of different clearance types, clearance size of motion pair and different clearance positions on the stability of pendulum. The results show that the axial clearance has little effect on the shimmy performance of landing gear; the radial clearance has a certain effect on the shimmy performance of medium speed running, which slightly improves the shimmy damping required by medium speed running; the rotational clearance affects the shimmy performance of the nose landing gear by affecting the force transmission of structural components. The required shimmy damping coefficient increases at low speed and decreases at high speed. The main reason for the return clearance is that during the return, the shimmy damper does not work, which leads to the decrease of the shimmy damping performance and the increase of the required shimmy damping coefficient in the whole speed range. Meanwhile, the structural clearance will increase the shimmy frequency of the nose landing gear. By analysing the yaw angle of the nose landing gear and the time domain curve of the yaw angle of the yaw damper, we can determine which structure of the landing gear and which type of clearance is the cause of the yaw. Finally, the coupling effect caused by the main structural parameters of the landing gear in “gap shimmy” was analysed according to different mechanical stability distances and strut stiffness of the nose landing gear, providing reference for aircraft anti-shimmy design, nose landing gear fault diagnosis and nose landing gear maintenance support.

This study presents a mathematical model that schedules arrival aircraft regarding RECAT-EU that is new categorisation for applying separation minima and analyses its effect on the performance of the Point Merge System (PMS) at Sabiha Gökcen International Airport (LTFJ). There are two main scenarios: one of them uses RECAT-EU and the other employs the ICAO wake turbulence category. Both scenarios have ten different test problems to examine the mathematical model. The model applies RECAT-EU wake turbulence categories and compares the outcome with the ICAO wake turbulence categories. The model aims to minimise flight duration on the sequencing leg and ground delay in the departure queue using the RECAT-EU and ICAO wake turbulence categories individually. The results were analysed to reveal the PMS performance using the two different approaches to turbulence categories. Statistical analysis was also carried out to compare the means of the two groups in the model.

An onboard three-dimensional (3D) trajectory generation approach based on the reinforcement learning (RL) algorithm and deep neural network (DNN) is proposed for hypersonic vehicles in glide phase. Multiple trajectory samples are generated offline through the convex optimisation method. The deep learning (DL) is employed to pre-train the DNN for initialising the actor network and accelerating the RL process. Based on the offline deep policy deterministic actor-critic algorithm, a flight target-oriented reward function with path constraints is designed. The actor network is optimised by the end-to-end RL and policy gradients of the critic network until the reward function converges to the maximum. The actor network is considered as the onboard trajectory generator to compute optimal control values online based on the real-time motion states. The simulation results show that the single-step online planning time meets the real-time requirements of onboard trajectory generation. The significant improvement in terminal accuracy of the online trajectory and the better generalisation under biased initial states for hypersonic vehicles in glide phase is observed.