Dilute aqueous smectite suspensions are well suited to convert into functional nanofilms. The functionalization is performed by ion exchange of amphiphilic molecules carrying the desired functionality. A functionalized clay mineral nanofilm is obtained by the organization of the molecules at the clay surface and by the organization of the elementary clay platelets in the film. Two techniques are presented: self-assembling and Langmuir-Blodgett (LB). Self-assembling is a very simple experiment, but the organizational order of the clay mineral particles is low. Nevertheless, films with nonlinear optical properties which are able to generate frequency-doubled light have been produced. The drawback of disorder of the clay platelets in the film can be largely overcome with the LB technique. Well organized films are obtained. In the presence of amphiphilic ruthenium(II)-bipyridine complexes, nonlinear optical properties are measured. In the presence of two dyes, oxacarbocyanine and rhodamine B, simultaneously adsorbed, efficient energy transfer between the donor (oxacarbocyanine) and the acceptor (rhodamine B) is measured. Fundamental research into the organization of molecules at clay mineral platelets is necessary to optimize the materials for specific applications.

A number of organobentonites were synthesized by exchanging the metal ions in bentonite with the cationic surfactant, cetyltrimethylammonium bromide. Samples of natural bentonite and organobentonites were analyzed for their organic carbon contents, examined by X-ray diffraction (XRD) for interlayer spacings, and viewed using a scanning electron microscope (SEM) for surface morphology. The sorption isotherm of benzene vapor from ambient air (relative humidity (RH) = 45 ± 5%) on natural bentonite was nonlinear; however, the isotherms of benzene from ambient air onto organobentonites were virtually linear over a large range of relative vapor concentrations. The sorption capacities of air-dried organobentonites were far greater than that of the natural bentonite. For air-dried organobentonites, the sorption coefficients correlated positively with the sample organic carbon contents and negatively with the sample BET-N2 surface areas. The heats of benzene vapor sorption onto air-dried organobentonites were less exothermic than the heat of benzene-vapor condensation. These findings suggest that benzene vapor sorption by air-dried organobentonites occurs essentially by vapor partition into the sample organic-matter fractions. This offers a potential application of organobentonites for the removal of organic vapors from flue gases and for assessing the efficiency of vapor removal.

Tris(8-hydroxyquinoline)aluminum (III) complexes (Alq3), one of the molecules studied most widely for organic light-emitting devices, were formed in the interlayer spaces of smectites by solid-solid reactions between Al-smectites (Al-montmorillonite and Al-synthetic saponite (Sumecton)) and 8-hydroxyquinoline (8Hq) at room temperature. The intercalation of 8-hydroxyquinoline molecules into Al-smectites was demonstrated by powder XRD, FTIR, DTA, TG, TG-MS, and chemical analysis. The coordination of the ligand to the interlayer Al cations was proved by FTIR, UV-Vis, and photoluminescence spectroscopies. The luminescence intensity of Alq3-Sumecton was much greater than that of Alq3-montmorillonite, and this was ascribed to the very small amount of quenching impurities in Sumecton.

The adsorption of hexadecyltrimethylammonium (HDTMA) in smectite was studied by adsorption isotherms, X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). Smectites that had reacted for 48 h with HDTMA cations equivalent to 0.2–3.0 times the cation exchange capacity (CEC) were converted to HDTMA-exchanged smectites with various d-spacings. Study of HDTMA-smectites by HRTEM suggests that the HDTMA adsorption results in interlayer expansion with various d-spacings and irregular wavy layer structures. We believe that HDTMA loading beyond the CEC of smectite affects the structure of clay by the additional adsorption of HDTMA-Br− via hydrophobic bonding. Surfactant orientation probably depends on the quantity of surfactant in the interlayer. Our TEM study shows that the structure of the adsorbed HDTMA layer in the interlayers of smectite depends on the charge distribution and chemical composition of smectite.

The aggregation behavior of one azine and three triphenylmethane cationic dyes in dispersions of reduced-charge montmorillonites (RCMs) was investigated. The extent and types of dye aggregation were monitored using visible spectroscopy. Similar relationships between dye aggregation and layer charge were observed, independent of the structure of the dye cations. High charge-density surfaces induced the formation of H-aggregates, with a face-to-face association between the dye cations that then absorb light at relatively lower wavelengths. Moderate reductions in layer charge were reflected in the lowering of the H-aggregation in favor of monomers, dimers and less densely-packed J-aggregates, absorbing light at higher wavelengths. Dye spectra in the presence of the lowest-charge RCMs resembled those of dilute dye solutions, indicating the absence of dye aggregation of any type in this case. The relationship between dye spectral changes and layer-charge densities of smectites is a general phenomenon which can potentially be used to estimate the layer charge of smectites. However, applying this method to triphenylmethane dyes, which have structurally more complicated cations, may reduce the sensitivity of the probe.

Oxidation-reduction processes within natural systems greatly influence the properties of sediments, soils and clays. The objective of this experimental study was to gather new evidence for the effects of changes in redox conditions (reduction and reoxidation) on structural properties of ferruginous smectite and to understand better the mechanisms involved. The <2 µm fraction of a ferruginous smectite (sample SWa-1), which contains 17.3 wt.% of total structural Fe, was studied by infrared (IR) spectroscopy. The pure Na-saturated clay was reduced by Na dithionite for 10 to 240 min to obtain various Fe(II):(total Fe) ratios ranging from 0 to 1.0. Selected reduced samples were then reoxidized completely by bubbling O2 gas through the suspensions for up to 12 h. Infrared spectra of the initially unaltered, reduced and reduced-reoxidized samples were collected. Reduction generated changes in the three studied spectral regions (O-H stretching, M-O-H deformation, and Si-O stretching), indicating that major modifications occurred within the clay crystal beyond merely a change in Fe oxidation state. partial dehydroxylation and redistribution of Fe, and perhaps Al, cations occurred upon reduction of SWa-1, changing the structural properties of its tetrahedral and octahedral sheets. Water molecules, probably generated by dehydroxylation within the octahedral sheet upon reduction, were tightly bound to the clay surface and were possibly trapped within the clay structure. Except for dehydroxylation and the Fe oxidation state, all these modifications were largely irreversible. The tightly bound water was not completely removed upon reoxidation and the cationic rearrangements generated during reduction were not reversed: either they were preserved as in the reduced state or cations were redistributed into a different configuration from the unreduced clay.

Several Al-substituted goethites were synthesized by hydrolysis of Fe3+ salt solutions. The kinetics of the reductive dissolution of these goethites in dithionite-ethylenediaminetetra acetic acid (D-EDTA) was studied at pH 5.5, at 303, 323 and 333 K. The initial dissolution rate (R) per unit of surface area decreases with Al substitution. In the sample with greater Al content (G″7), the kinetic profiles of the dissolved Fe fraction vs. time gave a small positive intercept. The kinetic profile of R as a function of EDTA initial concentration shows a significant weakening in the presence of Al. The maximum is flatter and wider in Al-substituted goethite than that of pure goethite. In sample G″7, where the Al content is 11.3 mol.% the maximum is obtained when the [D]:[EDTA] initial ratio is ∼4.5 vs. 2 in un-substituted goethite. These results can be attributed to the lesser density of the more active dimeric sites, the presence of more strongly bonded Al-O-Fe with regard to Fe-O and the small value for the ≡ Al-EDTA surface species constant. Activation energy (Ea) increases with Al substitution. Its value is doubled from GO (pure goethite) to G″7 (11.3 mol.% of Al). The frequency factor (A) acts in the opposite sense to Ea, but it is not sufficient to outweigh the effect of Ea.

This study of magnetic minerals in a weathering profile developed on plateau basalts of the subtropical southern Paraná Basin explores the evolution of titanomagnetite to titanomaghemite. Six samples studied by optical microscopy, X-ray diffraction (XRD), electron microprobe, Mössbauer spectroscopy (MS) and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS) support the interpretations.

The profile studied has two major parts: an upper, porous red-clay Latosol, ∼2–8 m deep, separated by a stone line from an underlying alterite which has two different facies — its argillaceous alterite consists of a clayey matrix with a well-developed fissure system whereas the underlying boulder alterite consists of rock cores surrounded by highly-porous cortexes of Al-goethite.

Optical microscopy showed the titanomagnetite-titanomaghem ite changes in color and shape through the profile. The decrease in the lattice parameter a of the magnetic separates from the rock cores to the alterite facies was detected by XRD. Mössbauer spectroscopy identified non-stoichiometric magnetite in the rock cores and Ti-substituted maghemite in the argillaceous alterite. Chemical analysis of the titanomagnetite-titanomaghe mite grains showed that the relative proportions of TiO2 and Fe2O3 vary in the different weathering facies. By SEM and EDS we also detected the presence of minor components as Si, Al, Ca, K, Mg and Mn.

These results led to the interpretation that the titanomagnetites from the fresh Parana basalts, located in the subtropical zone of Brazil, are unstable and gradually change to titanomaghemites. The evolution of these magnetic minerals is registered in the weathering facies related to climatic changes throughout geological time.

Kaolin samples from the Jari deposit (Amazon region) were studied using various techniques to characterize its structural and crystallochemical aspects, and to establish its origin and evolution. A profile 60 m thick was selected in a kaolin mine (Morro do Felipe) located at the banks of the Jari river. Despite the great thickness of the deposit and the variety of kaolin types, the mineralogical composition is rather homogeneous and is mainly kaolinite associated with gibbsite and small amounts of quartz, anatase, goethite and hematite. The field observations and the morphological analysis indicate the existence of sedimentary features throughout the whole profile except for the upper aluminous clayey layer (Belterra Clay). This is evidence that the Rio Jari kaolin deposit originated from sedimentary material, the Alter do Chão Formation. The presence of alternating clay and sandy layers is explained by sedimentation processes with great depositional energy variation. Thus, the accumulation of thick clay layers was related to a low-energy phase, and during the high-energy phases, the deposition process led to the accumulation of sandy materials, constituted essentially of quartz and showing strong textural and structural variation. Later on, periods of hydromorphy were responsible for iron removal and consequently for the bleaching of the sedimentary formation. The crystallinity data show an increase of the structural disorder toward the surface associated with an increase in the amount of structural Fe in the kaolinite. The Rio Jari kaolin deposits should be considered as having originated from kaolinitic clay sediments of the Alter do Chão formation (protore) that was submitted to intensive lateritic weathering processes.

Cronstedtite from Lostwithiel, Cornwall, England, in which two polytypic groups (A and C) are present within the same crystal, has been investigated using various techniques to reveal the distribution of the two groups and the relationship between polytypic structure and chemical composition. X-ray precession photographs from cleaved fragments of pyramidal crystals revealed the variable proportions of the two groups from the top to the base. Near the top, the crystal consists entirely of group C, with 1T as the dominant polytype. Near the base, both groups A and C are present. Back-scattered electron images from cross-sections parallel to the pyramidal axis showed mosaic contrast near the base, suggesting that two compositionally-different domains of several tens of microns in size are present, whereas the contrast was uniform near the top. Electron microprobe chemical analysis indicated the compositions $\left({\text{Fe}}_{2.31}^{2+}{\text{Fe}}_{0.69}^{3+}\right)\left({\text{Si}}_{1.31}{\text{Fe}}_{0.69}^{3+}\right){\text{O}}_5{\left(\text{OH}\right)}_4$ and $\left({\text{Fe}}_{2.16}^{2+}{\text{Fe}}_{0.84}^{3+}\right)\left({\text{Si}}_{1.16}{\text{Fe}}_{0.84}^{3+}\right){\text{O}}_5{\left(\text{OH}\right)}_4$. Electron back-scattered patterns (EBSPs) confirmed that the domain with Si-rich composition belongs to group C and that with Si-poor composition to group A. This is the first evidence that specific chemical compositions are related to the polytypic structures in cronstedtite. Transmission electron microscopy revealed that intergrowth of groups A and C at the monolayer level is also present as stacking disorder in both domains near the base, whereas such intergrowth was not observed in the region near the top.

The occurrence of kerolite in association with various secondary Ca-Mg carbonate mineral deposits (speleothems) was identified in basaltic sea caves on the island of Kauai, Hawaii. Kerolite is the dominant clay mineral in the deposits. X-ray diffraction (XRD) peaks of the kerolite are characteristically broadened indicating its extremely poor crystallinity. Few changes were observed in the XRD patterns of this kerolite when it was subjected to various humidity, temperature and ethylene-glycol treatments. The crystals appear as flaky masses with irregular or jagged edges in scanning (SEM) and transmission electron microscopy (TEM). Electron probe and energy dispersive X-ray (EDX) microanalysis show that the clay material is dominated by Mg-Si-O, with minor amounts of Al and Ca in some samples. The chemical composition, thermal analysis and TEM observations suggest that smaller amounts of an amorphous serpentine-like phase are mixed with the kerolite. Kerolite is often the only mineral associated with poorly mineralized, actively-growing microbial mats in these caves and it is common in completely lithified microbial mats. The latter commonly have microstromatolitic structures with kerolite as a dominant phase. These features suggest that kerolite formation is at least in part a result of microbial activity. The abundant extracellular polymers of the mat-forming bacteria bind and concentrate ions (Mg2+, silica) from solution and serve as nucleation sites for kerolite precipitation. Conditions within the mats also probably lead to formation of Mg-Si-gels, amorphous Mg-silicate precursors and ultimately kerolite. Evaporation of the cave solutions may also contribute to kerolite formation.

The ultrasound technique was applied to the synthesis of layered double hydroxides. The use of ultrasound in the synthesis of these compounds was studied in terms of its effect on their crystal qualities and surface properties. The crystal qualities of the compounds synthesized with ultrasound were compared with those of compounds synthesized without ultrasound to elucidate the effect of the ultrasound on the synthesis. The effect of crystal quality (crystallite size) on the adsorption behavior of humic substances was examined. The compounds synthesized under ultrasonic conditions showed a larger crystallite size and a larger adsorption capacity for humic substances than those synthesized without ultrasonic treatment. The degree of adsorption correlated well with crystal quality.