Using lock-in infrared microscopy as a tool for current detection on the micrometer scale in AC-driven specimens in combination with iterative grinding procedure allows preparation of current dominating microstructure regions on well-polished surfaces. This technique is applied successfully on varistor components based on specially doped ZnO-based varistor ceramics. This peculiar electroceramic material exhibits exceptional high nonlinear current–voltage (I-V) characteristics, described by a power law according I~Vα, caused by double Schottky barriers at the grain boundaries. As a novelty the thermographic response is used to evaluate local electrical properties, namely the nonlinearity coefficient α, on basis of higher order harmonics with respect to the basic electrical driving AC-frequency.

To correlate the observed electrical properties to the microstructure, the polar crystal orientation of the relevant ZnO grains is determined by combining electron backscatter diffraction and orientation-dependent patterns as a result of a chemical etching procedure. These findings support a modified new model for describing the grain boundary controlled current flow in a varistor microstructure including orientation-dependent barrier properties. Hence, the experimentally observed current direction-dependent behavior can be described consistently.

Single-particle reconstruction (SPR) and electron crystallography (EC), two major applications in electron microscopy, can be used to determine the structure of membrane proteins. The three-dimensional (3D) map is obtained from separated particles in conventional SPR, but from periodic unit cells in EC. Here, we report a refined SPR procedure for processing 2D crystal images. The method is applied to 2D crystals of melibiose permease, a secondary transporter in Escherichia coli. The current procedure is improved from our previously published one in several aspects. The “gold standard Fourier shell correlation” resolution of our final reconstruction reaches 13 Å, which is significantly better than the previously obtained 17 Å resolution. The choices of different refinement parameters for reconstruction are discussed. Our refined SPR procedure could be applied to determine the structure of other membrane proteins in small or locally distorted 2D crystals, which are not ideal for EC.

The present study characterizes the main deterioration mechanisms affecting the early 17th frescoes of Casa de Fresco, the only known example in Portugal of a semi-underground leisure room richly decorated with a balcony over a water well. Frescoes from the vault are at risk due to salt weathering and biodeterioration. The aim of the research was identification of the deterioration materials, determination of their origin, and their effect on the frescoes before future intervention. Scanning electron microscopy with an energy-dispersive X-ray detector (SEM-EDS) was used to determine salt morphology and microanalysis. The mineralogical characterization was performed by X-ray powder diffraction, complemented with µ-Raman and µ-Fourier transform infrared spectroscopy. Biological assessment was evaluated with optical microscopy and SEM-EDS. Bacterial and fungal isolation and identification were performed using standard culture media and methods according to Bergey’s Manual of Systematic Bacteriology and from the Compendium of Soil Fungi. The results show that Ca and Ca-Mg carbonates from the paint renderings are the predominant salt species affecting the site. Bacterial strains from the genera Bacillus and Pseudomonas and fungal strains from the Cladosporium spp. and Penicillium spp. were isolated in the salt formations, within and between the mortar layers. Azurite, malachite, and smalt paint layers are the most affected by the weathering conditions.

In this paper, the traceability of copper from the anode to the cathode and then the wire rod has been studied in terms of impurity content, microstructure, texture, recrystallization kinetics, and ductility. These characterizations were obtained based on secondary ion mass spectrometry, differential scanning calorimetry (DSC), X-ray diffraction, HV hardness, and electron backscattered diffraction. It is shown that the recrystallization was delayed by the total amount of impurities. From tensile tests performed on cold drawn and subsequently annealed wires for a given time, a simplified model has been developed to link tensile elongation to the chemical composition. This model allowed quantification of the contribution of some additional elements, present in small quantity, on the recrystallization kinetics. The proposed model adjusted for the cold-drawn wires was also validated on both the cathode and wire rod used for the study of traceability.

In this work, we report the preparation of ultrathin submicro- and nanoporous cellulose films onto Si (100). The effect of different experimental conditions of preparation on the film surface morphology was studied, namely the role of the film casting method (spin- versus dip-coating), solvent (toluene or tetrahydrofuran), substrate pretreatment (hydrophilicity degree), and regeneration procedure with HCl vapors (two consecutive dips followed by regeneration or regeneration after each dip). The surface morphological structures presented in this work were never obtained before without the use of templates. A rather regular two-dimensional pore network was obtained onto the less hydrophilic Si substrate (contact angle≅68°), after two consecutive dips (with an intercalary rotation of 180º) in trimethylsilyl cellulose diluted in toluene and regeneration at the end. All the surfaces were characterized by atomic force microscopy.

Tributyltin, an organotin, is ubiquitous in estuaries and freshwater systems. Previous reports suggest that tributyltin is an endocrine disruptor in many wildlife species and it inhibits aromatase in mammalian placental and granulosa-like tumor cell lines. However, no evidence showing the effects of tributyltin on oocytes or preimplantation embryonic developmental competence exists. Therefore, we investigated the role of tributyltin chloride (TBTCl) in the development of female oocytes and preimplantation embryos. Briefly, female ICR mice were gavaged with 0 (vehicle), 4, and 8 mg/kg of TBTCl each day for 18 days. The fluorescence intensity analysis showed that the 5-methylcytosine level decreased after TBTCl treatment, indicating that the general DNA methylation level decreased in the treated oocytes. Our results demonstrate that TBTCl treatment results in decreased mRNA levels of imprinted genes H19, Igf2r, and Peg3 during oocyte growth. The TBTCl-treated oocytes showed a significant increase in reactive oxygen species levels in germinal vesicle oocytes. In TBTCl-treated oocytes, there was no difference in GPx and Sod1 expression, but a decreased mRNA level of Cat occurred when compared with control. Moreover, the blastocysts with TBTCl exposure displayed higher apoptotic signals. These results suggest that TBTCl induces developmental defects in oocytes and preimplantation embryos.

In order to achieve reliable structural characterization by transmission electron microscopy, beam-induced structural changes should be clarified for any target material system. As an example, the movement of heavy adatoms on a thin carbon support has been repeatedly reported under the electron beam while the underlying reason for such motion is still in debate. By applying statistical analysis to the group behavior of gold adatoms, we investigated their motion under different beam conditions and detected features corresponding to beam-induced motion, under typical scanning transmission electron microscopy observation conditions. Our results are consistent with the theoretical prediction proposed by Egerton (2013).

In biology, hemocytometers such as Malassez slides are widely used and are effective tools for counting cells manually. In a previous work, a robust algorithm was developed for grid extraction in Malassez slide images. This algorithm was evaluated on a set of 135 images and grids were accurately detected in most cases, but there remained failures for the most difficult images. In this work, we present an optimization of this algorithm that allows for 100% grid detection and a 25% improvement in grid positioning accuracy. These improvements make the algorithm fully reliable for grid detection. This optimization also allows complete erasing of the grid without altering the cells, which eases their segmentation.

Laser triangulation is widely used to measure three-dimensional structure of surfaces. The technique is suitable for macroscopic and microscopic surface measurements. In this paper, the measurement uncertainty of laser triangulation is investigated on technical surfaces for microscopic measurement applications. Properties of technical surfaces are, for example, reflectivity, surface roughness, and the presence of scratches and pores. These properties are more influential in the microscopic laser triangulation than in the macroscopic one. In the Introduction section of this paper, the measurement uncertainty of laser triangulation is experimentally investigated for 13 different specimens. The measurements were carried out with and without a laser speckle reducer. In the Materials and Methods section of this paper, the surfaces of the 13 specimens are characterized in order to be able to find correlations between the surface properties and the measurement uncertainty. The last section of this paper describes simulations of the measurement uncertainty, which allow for the calculation of the measurement uncertainty with only one source of uncertainty present. The considerations in this paper allow for the assessment of the measurement uncertainty of laser triangulation on any technical surface when some surface properties, such as roughness, are known.