The purpose of this study was to evaluate if mechanical loading influences bioactivity and bond strength at the resin–dentin interface after bonding with Zn-doped etch-and-rinse adhesives. Dentin surfaces were subjected to demineralization by 37% phosphoric acid (PA) or 0.5 M ethylenediaminetetraacetic acid (EDTA). Single bond (SB) adhesive—3M ESPE—SB+ZnO particles 20 wt% and SB+ZnCl2 2 wt% were applied on treated dentin to create the groups PA+SB, SB+ZnO, SB+ZnCl2, EDTA+SB, EDTA+ZnO, and EDTA+ZnCl2. Bonded interfaces were stored in simulated body fluid for 24 h and tested or submitted to mechanical loading. Microtensile bond strength (MTBS) was assessed. Debonded dentin surfaces were studied by high-resolution scanning electron microscopy. Remineralization of the bonded interfaces was assessed by atomic force microscope imaging/nanoindentation, Raman spectroscopy/cluster analysis, and Masson’s trichrome staining. Load cycling (LC) produced reduction in MTBS in all PA+SB, and no change was encountered in EDTA+SB specimens, regardless of zinc doping. LC increased the mineralization and crystallographic maturity at the interface; a higher effect was noticed when using ZnO. Trichrome staining reflected a narrow demineralized dentin matrix after loading of dentin surfaces that were treated with SB-doped adhesives. This correlates with an increase in mineral platforms or plate-like multilayered crystals in PA or EDTA-treated dentin surfaces, respectively.

The recently developed three-dimensional electron microscopic (EM) method of serial block-face scanning electron microscopy (SBEM) has rapidly established itself as a powerful imaging approach. Volume EM imaging with this scanning electron microscopy (SEM) method requires intense staining of biological specimens with heavy metals to allow sufficient back-scatter electron signal and also to render specimens sufficiently conductive to control charging artifacts. These more extreme heavy metal staining protocols render specimens light opaque and make it much more difficult to track and identify regions of interest (ROIs) for the SBEM imaging process than for a typical thin section transmission electron microscopy correlative light and electron microscopy study. We present a strategy employing X-ray microscopy (XRM) both for tracking ROIs and for increasing the efficiency of the workflow used for typical projects undertaken with SBEM. XRM was found to reveal an impressive level of detail in tissue heavily stained for SBEM imaging, allowing for the identification of tissue landmarks that can be subsequently used to guide data collection in the SEM. Furthermore, specific labeling of individual cells using diaminobenzidine is detectable in XRM volumes. We demonstrate that tungsten carbide particles or upconverting nanophosphor particles can be used as fiducial markers to further increase the precision and efficiency of SBEM imaging.

In biology, cell counting is a primary measurement and it is usually performed manually using hemocytometers such as Malassez blades. This work is tedious and can be automated using image processing. An algorithm based on Fourier transform filtering and the Hough transform was developed for Malassez blade grid extraction. This facilitates cell segmentation and counting within the grid. For the present work, a set of 137 images with high variability was processed. Grids were accurately detected in 98% of these images.

Whole slide imaging (WSI) can be used to quantify multiple responses within tissue sections during histological analysis. Feature Analysis on Consecutive Tissue Sections (FACTS®) allows the investigator to perform digital morphometric analysis (DMA) within specified regions of interest (ROI) across multiple serial sections at faster rates when compared with manual morphometry methods. Using FACTS® in conjunction with WSI is a powerful analysis tool, which allows DMA to target specific ROI across multiple tissue sections stained for different biomarkers. DMA may serve as an appropriate alternative to classic, manual, histologic morphometric measures, which have historically relied on the selection of high-powered fields of views and manual scoring (e.g., a gold standard). In the current study, existing preserved samples were used to determine if DMA would provide similar results to manual counting methods. Rodent hearts (n=14, left ventricles) were stained with Masson’s trichrome, and reacted for cluster of differentiation 68 (CD-68). This study found no statistical significant difference between a classic, manual method and the use of digital algorithms to perform the similar counts (p=0.38). DMA offers researchers the ability to accurately evaluate morphological characteristics in a reproducible fashion without investigator bias and with higher throughput.

The adaptive significance of variation in sperm phenotype is still largely unknown, in part due to the difficulties of observing and measuring sperm movement in its natural, selective environment (i.e., within the female reproductive tract). Computer-assisted sperm analysis systems allow objective and accurate measurement of sperm velocity, but rely on being able to track individual sperm, and are therefore unable to measure sperm movement in species where sperm move in trains or bundles. Here we describe a newly developed computational method for measuring sperm movement using Fourier analysis to estimate sperm tail beat frequency. High-speed time-lapse videos of sperm movement within the female tract of the neriid fly Telostylinus angusticollis were recorded, and a map of beat frequencies generated by converting the periodic signal of an intensity versus time trace at each pixel to the frequency domain using the Fourier transform. We were able to detect small decreases in sperm tail beat frequency over time, indicating the method is sensitive enough to identify consistent differences in sperm movement. Fourier analysis can be applied to a wide range of species and contexts, and should therefore facilitate novel exploration of the causes and consequences of variation in sperm movement.

The aim of the present study was to investigate poikilocytosis in Labeo rohita (an important food fish) as an early indicator of stress due to an azo dye, Basic Violet-1 (CI: 42535). This dye was observed to be very toxic to test fish (96 h LC50 as0.45 mg/L dye). Fish were given short-term (96 h) and subchronic (150 days) exposures to the dye, and poikilocytosis was recorded under light and scanning electron microscopy (SEM). Light microscopy helped in identification of micronuclei along with irregularities, notches, blebs, lobes, crenation, clumps, chains, spherocytes, vacuolation, and necrosis in erythrocytes. However, SEM indicated shrinkage, oozing of cytoplasm, and several new abnormal shapes including marginal foldings, discocytes, keratocytes, dacrocytes, degmacytes, acanthocytes, echinocytes, protuberances, stomatocytes, drepanocytes, holes in the membrane, stippling/spicules, crescent-shaped cells, triangular cells, and pentagonal cells. Earlier studies speculated changes in the membrane to be responsible for clumping and chaining of erythrocytes, whereas the present SEM study clearly indicates that oozing out of cytoplasm is also responsible for the formation of chains and clumps. This study also shows that erythrocytes exhibit pathological symptoms before the appearance of other external symptoms such as abnormal behavior or mortality of fish. There was a dose- and duration-dependent increase; therefore, poikilocytosis, especially echinocytes, spherocytes, and clumps, can act as a biomarker for the stress caused by azo dyes.