Effects of boundary conditions on the performance of compact oscillatory momentum and vorticity generators, commonly known as ‘synthetic jet’, ejecting a train of vortex-pairs into still air, were studied experimentally. The different boundary conditions altered the near-device entrainment process of the zero-net-mass-flux actuator. The measurements included hot-wire and Particle Image Velocimetry, cavity pressures and temperatures.

When the actuator operates in still air, a quasi-2D vortex pair is generated due to the extreme shear at the edges of the fluid slug ejected during the blowing stage of each excitation cycle. The vorticity flux exiting the slot determines the resulting vortex-pair circulation. The threshold slot exit velocity, for the current configuration and operating conditions, determines if the vortices will be sucked into the actuator’s cavity or be released. Once released, the vortex convection speed approximately scales with the peak velocity at the slot exit. However, the normalised convection velocity increases with the slot Reynolds number.

When even a very short extension is attached to one ‘lip’ of the actuator exit, the jet is deflected in the direction opposite the extended lip, due to the restriction on the entrainment process. When long, one ‘lip’ extension is attached, such that the vortex pair is ejected parallel to a plate, the coherence of the vortices improve, their phase speed and magnitude decrease.

The effects of high-frequency excitation, ejected perpendicular to a wall into still air, were also investigated. It was found that the presence of the plate does not have a measurable effect on the wall normal excitation, indicating that the majority of the entrainment is taking place from the forward 180° of the actuator exit plane. When the slot is inclined to the surface at a shallow angle of 30 degrees, an unsteady wall jet is formed, transferring momentum along the wall. This is a direct result of the symmetry break, altering the relative magnitudes of the vortex pair.

This paper describes a study which has been concerned with numerical predictions of the airwakes resulting from two simplified ship geometries: the internationally agreed Simple Frigate Shape, SFS1, and its successor, SFS2. Extensive steady-state simulations have been carried out for a wide range of wind conditions using Fluent, a commercially available Computational Fluid Dynamics (CFD) code. The CFD predictions have been partially validated against wind tunnel data produced by the National Research Council of Canada (NRC) and have shown good agreement. The resulting airwake velocity components have been exported from Fluent, interpolated onto suitable grids and attached to the FLIGHTLAB flight-simulation environment as look-up tables; piloted flight trials were then carried out using the Liverpool full-motion simulator. The pilot workload and helicopter control margins resulting from a range of wind-over-deck conditions have been used to develop the Ship-Helicopter Operating Limits (SHOL) for a Lynx-like helicopter and the SFS2. The workload was compared to the pilot’s experiences on a similar aircraft and a Type 23 Frigate and the simulated SHOL compared with SHOLs derived from sea trials. The results are very encouraging and open up further the long awaited prospect of such simulations being used in the future to reduce at-sea trials, and to provide a safe environment for pilot training.

Any time a new aircraft is introduced into service, or an old aircraft undergoes substantial modifications or needs to be certified to carry and employ new stores, the store separation engineer is faced with a decision about how much effort will be required to provide an airworthiness certification for the aircraft and stores. Generally, there are three approaches that have been used: wind-tunnel testing, computational fluid dynamics (CFD) analyses and flight testing. During the past twenty years there have been considerable advances in all three areas. In particular, there has been a considerable improvement in the speed and validity of CFD results for store separation. The Holy Grail of CFD has long been the reduction/replacement of wind-tunnel testing. This would mean in store separation the ability to go from a CFD calculation to flight testing at the end point. The paper will describe how this was achieved for the F/A-18C/Litening pod program.

The relationship between a pilot workload rating for a simulated flight task in the proximity of an offshore platform helideck and three experimental factors – wind speed, wind direction and pilot is investigated. The statistical method employed is ordinal logistic regression, which allows the specifying and fitting of regression relationships between ordered categorical response variables and explanatory variables. The response variable in this context is a pilot’s rating of the workload induced by certain flight tasks, measured on an ordered categorical scale 1 to 10. Estimates of the effects of the explanatory variables are given and their practical significance discussed.

A system of systems study plan was developed and a prototype was executed to optimise a recommended military force structure. This methodology defined the optimal force structure, using constrained optimisation to reflect budget limitations and desired mission performance. The force structure included surface and air assets, a command, control, communications, computers, intelligence, surveillance and reconnaissance (C4ISR) architecture, and a recommended logistics infrastructure. A second aspect of the study plan defined the total acquisition strategy, which accounted for: retiring legacy assets, extending the service life of existing assets until new replacements became available, and acquiring new assets for deployment, within the budget allocation. This methodology combined various modeling and simulation techniques to meet three study objectives. First, a nonlinear mixed integer programming model maximised performance, subject to cost constraints, cost as an independent variable (CAIV). Second, a dynamic programming model scheduled the transition from the legacy force structure to the future force, defined by the previous modeling technique. Third, a process simulation model simulated performance, over a one-year time period, for 25 areas of responsibility and five missions. This model verified performance estimates generated by the previous models.