Hostname: page-component-848d4c4894-jbqgn Total loading time: 0 Render date: 2024-06-23T07:57:26.186Z Has data issue: false hasContentIssue false
  • English
  • Français

Fabrication of Ni–Al thin films by the pulsed laser deposition technique

Published online by Cambridge University Press:  31 January 2011

R.K. Singh ,
Deepika Bhattacharya ,
S. Sharan ,
P. Tiwari  and
J. Narayan
R.K. Singh
Affiliation:
Materials Science and Engineering Department, University of Florida, Gainesville, Florida 32611-2066
Deepika Bhattacharya
Affiliation:
Materials Science and Engineering Department, University of Florida, Gainesville, Florida 32611-2066
S. Sharan
Affiliation:
Materials Science and Engineering Department, North Carolina State University, Raleigh, North Carolina 27695-7916
P. Tiwari
Affiliation:
Materials Science and Engineering Department, North Carolina State University, Raleigh, North Carolina 27695-7916
J. Narayan
Affiliation:
Materials Science and Engineering Department, North Carolina State University, Raleigh, North Carolina 27695-7916
Get access

Abstract

We have fabricated Ni3Al and NiAl thin films on different substrates by the pulsed laser deposition (PLD) technique. A high energy nanosecond laser beam was directed onto Ni–Al (NiAl, Ni3Al) targets, and the evaporated material was deposited onto substrates placed parallel to the target. The substrate temperature was varied between 300 and 400 °C, and the substrate-target distance was maintained at approximately 5 cm. The films were analyzed using scanning electron microscopy, transmission electron microscopy, x-ray diffraction, and Rutherford backscattering spectrometry. At energy densities slightly above the evaporation threshold, a slight enrichment of Al was observed, while at higher energy densities the film stoichiometry was close (<5%) to the target composition. Barring a few particles, the surface of the films exhibited a smooth morphology. X-ray and TEM results corroborated the formation of Ni3Al and NiAl films from similar target compositions. These films were characterized by small randomly oriented grains with grain size varying between 200 and 400 Å.

Type
Rapid Communications
Information
Journal of Materials Research , Volume 7 , Issue 10 , October 1992 , pp. 2639 - 2642
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Colgan, E.G. and Mayer, J.W., in Thin Films– Interfaces and Phenomena, edited by Nemanich, R. J., Ho, P. S., and Lau, S. S. (Mater. Res. Soc. Symp. Proc. 54, Pittsburgh, PA, 1986), p. 121.Google Scholar
2Takeyama, M. and Liu, C.T., J. Mater. Res. 3, 665 (1988).CrossRefGoogle Scholar
3Rose-Innes, A. C. and Rhoderick, E. H., Introduction to Superconductivity, 2nd ed. (Pergamon Press, Oxford, 1978); W. Hume-Rothery, R. E. Smallman, and C. W. Haworth, The Structure of Metals and Alloys (Institute of Metals, London, 1969).Google Scholar
4Castleman, L. S. and Siegle, L. L., Trans. TMS-AIME 212, 589 (1958).Google Scholar
5Janssen, M.M.P. and Rieck, G.D., Trans. TMS-AIME 239, 1372 (1967).Google Scholar
6Shankar, S. and Siegle, L. L., Metall. Trans. 9A, 1467 (1978).Google Scholar
7Cheung, J.T. and Sankur, H., CRC Crit. Rev. Solid State Mater. Sci. 15, 63 (1988).CrossRefGoogle Scholar
8Cotell, C.M., Chrisey, D.B., Grabowski, K.S., Sprague, J.A., and Gossett, C. R., J. Appl. Biomaterials (in press).Google Scholar
9Singh, R. K. and Narayan, J., Phys. Rev. B 41, 8843 (1990).Google Scholar
10Singh, R. K., Narayan, J., Singh, A. K., and Krishnaswamy, J., Appl. Phys. Lett. 54, 2271 (1989).Google Scholar
11Narayan, J., Biunno, N., Singh, R. K., Auchiello, O., and Holland, O.W., Appl. Phys. Lett. 51, 1845 (1987).Google Scholar
12Singh, R.K., Bhattacharya, D., and Narayan, J., Appl. Phys. Lett. 57, 2022 (1990).Google Scholar