In the proposed paper, a novel design and realization of a wide-band, oblique angle-insensitive metamaterial absorbers are presented. The absorber is designed to work over a wide range of frequencies, making it suitable for Ku-band applications. To get wide band absorption, a novel SM-shaped design with a square-tooth circular ring resonator structure is designed efficiently. The unit cell structure is designed with a dielectric substrate (FR4) with a thickness of 3.2 mm (0.16λ0), where λ0 is the wavelength of free space. The novel design of this configuration leads to wideband absorption with respect to a conventional absorber. Several physical parameters are also investigated, such as the dielectric constant, permittivity, permeability, impedance, and negative refractive index. The simulation and experimental results show from 13.60 to 16.14 GHz with 99.1% absorption, which is excellent agreement. The analysis of the proposed design indicates that it possesses the remarkable feature of being insensitive to polarization while also exhibiting high absorption even when the angle of incidence varies. For both the simulation and experiment, results are consistent with a frequency range of 13.60–16.14 GHz for normal incidence. Almost perfect absorption works well for solar cells, EM detection, and imaging applications.

A novel wideband reflectarray antenna (RA) is designed for 5G millimeter (mm) wave communications in the frequency range of 26.5–36 GHz. The proposed unit cell is constructed using a grid periodicity of 0.52${{\lambda }_0}{ }$ that offers 636° phase change through phase delay lines (PDLs) (${{\theta }_{\text{s}}}$). These PDLs are attached to the outer end of the unit cell comprising semi-circular rings. Bandwidth enhancement is achieved by incorporating a corrugated slot technique and a suitable air gap beneath the substrate. The proposed center-fed reflectarray is composed of 513 elements distributed in a circular aperture (13.46${{\lambda }_0}$). Using mirror-symmetrical distribution of the unit cells, a cross-polarization reduction as low as −50 dB is realized. At 30 GHz, RA has a measured peak gain of 28.2 dBi, a sidelobe level of −14.3 dB, and an aperture efficiency of 31.4%. The prototype antenna is fabricated, and the simulation results are experimentally validated. The measured 1-dB and 3-dB gain bandwidths of the proposed reflectarray antenna are 31.3% and 41.6%, respectively. The proposed broadband reflectarray can be a potential choice for inter-satellite services like inter-satellite networking/satellite positioning and control; fixed satellite services such as GPS satellite synchronization and data direct to home TV; and satellite position fixing.

In this paper, a novel tunable dual-band bandpass filter (BPF) with independently controlled passbands and constant absolute bandwidth (CABW) is proposed. The CABW passbands of designed dual-band BPF are obtained using manageable electric and magnetic mix coupling. Furthermore, the multiple transmission paths from the input port to the output port are extended for extra transmission zeros, which results in modified selectivity of the proposed dual-band BPF. The tunability and switchability of the developed filter can be implemented by introducing a single bias voltage of varactors for each band. For the tunable dual-band BPF, the simulated results show that the center frequency (CF) of the first passband varies from 2.38 to 2.68 GHz, and the CF of the second passband varies from 3.28 to 3.88 GHz, while 3-dB absolute bandwidths are 101 ± 7 MHz and 98 ± 4 MHz, respectively. Moreover, the two passbands of the filter can also be independently switched by removing the voltage imposed on the varactor CV1 and CV2. The measured results agree well with simulated results, which verify the design theory.

This paper proposes a design method for designing a wideband filtering power amplifier (PA) based on terminated coupled line structure (TCLS). This method generates four transmission zeros and three transmission poles by loading stepped impedance resonator and short-circuit stubs on the four ports of TCLS, which greatly optimizes the in-band return loss and stopband suppression of the output matching network. In addition, the effective suppression of the second harmonic also increases the efficiency of the PA. In order to verify the effectiveness and superiority of this design method, a wideband bandpass filtering PA is designed and manufactured in 2.9–3.7 GHz. Measurement results show that the saturated output power is from 40.1 dBm to 41.2 dBm, the drain efficiency is greater than 60.3%, and the gain is 10–11.2 dB.

An enhanced wideband tracking method for characteristic modes (CMs) is investigated in this paper. The method consists of three stages, and its core tracking stage (CTS) is based on a classical eigenvector correlation-based algorithm. To decrease the tracking time and eliminate the crossing avoidance (CRA), we append a commonly used eigenvalue filter (EF) as the preprocessing stage and a novel postprocessing stage to the CTS. The proposed postprocessing stage can identify all CRA mode pairs by analyzing their trajectory and correlation characteristics. Subsequently, it can predict corresponding CRA frequencies and correct problematic qualities rapidly. Considering potential variations in eigenvector numbers at consecutive frequency samples caused by the EF, a new execution condition for the adaptive frequency adjustment in the CTS is introduced. Finally, CMs of a conductor plate and a fractal structure are investigated to demonstrate the performance of the proposed method, and the obtained results are discussed.

A novel wideband nonuniform metasurface antenna with stable gain is demonstrated. The nonuniform metasurface is composed of square patches and rings and is excited by a slot antenna. Based on characteristic mode analysis, two characteristic modes with same current direction are selected to achieve stable radiation performance in a wide frequency range. The wideband operation is achieved by assembling the resonant modes of the metasurface and slot antenna. The measured results show that the −10 dB impedance bandwidth of the proposed antenna is from 4.3 to 8.4 GHz (64.57%), and the 2 dB gain bandwidth is from 4.3 to 6.2 GHz (36.2%) with a peak gain value of 9.42 dBi. Moreover, broadside radiation performance is achieved.

This paper proposes a lightweight frequency selective surface polarization-insensitive wideband metamaterial absorber in C band and X band that employs only a few resistive elements. The proposed absorber is embodied with four quadrature slotted inner circular patch, which is horizontally and vertically bisected, and outer concentric copper rings of 0.035 mm thickness are attached with four lumped resistors placed at 90° apart. A slotted inner circular patch provides significant inductive and capacitive loading. The absorption bandwidth of 8.02 GHz with more than 90% absorption is observed from 5.69 to 13.71 GHz under normal incidence and maintains almost same absorptivity range under oblique incidence up to 45° in both transverse electric mode and transverse magnetic mode. The designed metamaterial absorber is fabricated and measured using free space measurement technique. The actual experiments and the simulated ones are in good agreement.

Circular antenna array (CAA) is one of the most widely used antenna array designs. This paper addresses the design challenges of the CAA with the non-uniform single ring, which is placed in an X-Y plane with the best sidelobe level (SLL) and improved first null beamwidth (FNBW). It has been solved using differential evolution, craziness-based particle swarm optimization (CRPSO), and novel particle swarm optimization (NPSO) techniques. An optimal combination of feeding current and inter-element spacing provides an array pattern with the best SLL and improved FNBW, as well as some other parameter calculations of the antenna array like maximum directivity, maximum effective aperture, total effective aperture, maximum beam area, total beam area, circumference, and radius of the CAAs using these techniques. There are six designs of CAAs with different antenna elements (i.e., 10-, 12-, 16-, 20-, 36-, and 64-elements) which have been taken into account. Simulations are done in MATLAB. Based on various simulation results, we can analyze the performance of SLL and FNBW with other parameters using NPSO and compare them with different techniques of CAAs, as shown in the numerical analysis and simulation result section.

The Muscle Analyzer System (MAS) project wants to create a standalone microwave device that can assess the muscle quality, called the MAS device. To achieve that an algorithm that can derive the properties of skin, fat and muscle from the measurements is needed. This paper presents a machine learning algorithm that aims to do precisely that. The algorithm relies on first predicting the skin using the data from the MAS device, then predicting the fat again using the data from the MAS but also the predicted skin value and lastly the muscle is predicted using the microwave data together with the skin and fat predictions. Data have been collected in phantom experiments, materials that mimick the dielectric properties of human tissues. The algorithm is trained to predict the properties of said phantoms. The results show that the prediction for skin thickness works well, the fat thickness prediction is okay but the muscle prediction struggles. This is partly due to the error from the skin and fat layers are propagated to the muscle layer and partly because the muscle layer is farthest away from the sensor, which makes getting information from that layer harder.

This paper presents a broadband circularly polarized (CP) antenna array for millimeter-wave applications, and the antenna array has the advantages of wide impedance bandwidth (IBW), novel CP design, and low profile. The antenna unit consists of a two-layer substrate and two pairs of magnetoelectric dipoles. Stepped microstrip lines coupled by rectangular slits form a feeder network for easy integration. The axial ratio bandwidth (ARBW) is extended because a pair of parasitic patches is loaded and an elliptical perturbation is added. The simulation results show that the antenna has an ARBW of 18.6% (26.4–31.9 GHz) and an IBW of 45.5% (20.6–32.7 GHz), with a gain greater than 7.11 dBic in the IBW. To improve the gain of the antenna, a 2 × 2 antenna array is designed, fabricated, and measured. The measured results show that the array has an ARBW of 16.6% (26.42–31.21 GHz), an IBW of 41.6% (22.28–33.97 GHz), a peak gain of 13.89 dBic in the IBW, the cross-polarization levels in the xoz-plane and yoz-plane are above 20 dB, and a radiation efficiency greater than 89%.

In this paper, we investigate low-cost solutions for enabling ground moving target indication applications with multichannel mobile passive radar systems. As known, in order to be competitive with their active counterparts, passive radars are typically characterized by severe constraints in terms of cost, complexity, and compactness, especially when installed on moving platforms. On the one hand, carrying out the computations onboard requires processing techniques as simple as possible. On the other hand, the need for lightweight and compact systems that can be installed on a moving platform requires using a limited number of receiving channels. To meet these requirements, we propose a series of nonadaptive detectors based on multichannel displaced phase center antennas, which allow suppressing the Doppler-spread clutter component without requiring computationally intensive space–time adaptive processing techniques. Moreover, we explore the use of nonuniformly spaced array configurations on receive, which represent a good alternative to conventional uniform linear arrays when a limited number of receiving channels can be implemented. The effectiveness of the proposed processing techniques and antenna design solutions is demonstrated via numerical analysis for the case of a DVB-T-based mobile passive radar system.

This paper outlines the results of particle-in-cell simulations of a relativistic magnetron with six cavities and a transparent cathode configuration. Excitation of the π mode in the interaction region was attained, which in turn led to $\textrm{TE}_{11}$ mode emission of microwaves to the waveguide. This mode transformation was achieved with a non-symmetric diffraction output, consisting of four large and two small tapered cavities. Simulations were performed with a voltage across the anode-cathode gap varying from 164 to 356 kV, and axial magnetic field strengths between 0.24 and 0.34 T. Maximum efficiency of 37% was obtained with a peak output power of 590 MW, having a voltage of 261 kV and a magnetic field of 0.30 T. Furthermore, a frequency of 2.57 GHz and a rise time of microwaves at the waveguide of 15 ns were demonstrated. The electron leakage current was shown to decrease from ∼10$\%$ to less than $1\%$ when employing a longer interaction region, while still exhibiting good performance. Additionally, we show that there is an optimal range of voltages given a magnetic field, for which π mode excitation with high efficiency is attained.

A multi-band circularly polarized antenna is proposed for WLAN (2.4/5.3/5.8 GHz) and WiMAX (3.5 GHz) applications. The proposed antenna is constructed of a radiation patch and a reflecting metal ground. Characteristic mode theory is utilized to analyze the modes of the patch and based on these results the antenna is optimized. The −10 dB impedance bandwidths of the proposed antenna are 53.53% (2.4–4.15 GHz) and 47.28% (5.25–8.5 GHz), respectively. The antenna radiates left-handed circular polarization in the lower band and right-handed circular polarization in the upper band. A maximum gain of 10 dBic is achieved for the proposed antenna.

A novel thinned antenna element distribution for cancelling grating lobes (GLs) as well as for reducing phase shifters (PSs) is presented for a two-dimensional phased-array automotive radar application. First, an efficient clustering technique of vertical adjacent elements is employed with array thinning for a PS reduction of 66.7%. In the proposed distribution, several single-element radiators (non-clustered antenna elements) are placed in the vertical direction with specific spacing in a grid of 16 × 12 (192) elements with λ/2 pitch. This disrupts the periodicity of phase-centers after element-clustering and takes a role as steerable GL canceller with capabilities of tracking and nullifying the GL at any scan angle. The proposed distribution enables beam steering up to ±60° in the azimuth plane, as well as ±25° in the elevation plane with cancelled GL and sidelobes. Furthermore, the proposed distribution has been efficiently calibrated with all elements activated by introducing the code division multiple access technique. To the best of the authors’ knowledge, this work represents the first fully calibrated state-of-the-art thinned distribution phased-array including a novel steerable GL canceller to track and nullify GLs.

Wireless power transfer (WPT) is an emerging technology with many promising applications where transmitting power via wired connections is undesirable. However, near-field WPT between magnetically coupled inductors is highly susceptible to positional changes, with power transfer efficiency (PTE) suffering if the coils are misaligned. To combat this effect, many position-independent, self-adaptive, inductive WPT schemes have been developed. Recent work indicates that it is possible to passively achieve high PTE across the operating range with nonlinear capacitors. In this work, the functionality of nonlinear WPT circuits is investigated, and fundamental design equations are derived and validated. A simplified design procedure is proposed for the position-independent self-adaptive WPT using nonlinear capacitors, wherein the ideal capacitance is extracted for each coupling factor. The efficacy of the method is demonstrated with an experimental circuit. Future work in this area is also proposed.

A two-port ceramic-based antenna loaded with partially reflecting surface (PRS) is structured and explored. Fan-shaped slot is utilized to create circularly polarized wave in both frequency ranges. Dual frequency ranges are due to hybrid mode creation inside the ceramic material, i.e. HEM11δ and HEM12δ modes. PRS is used to change the phase gradient, which in turn tilts the radiation beam (±35°) obtained from different port in opposite direction. This concept is useful to reduce the envelop correlation coefficient using far-field. Experimental verification confirms that the designed antenna works from 26.1 to 27.5 GHz and 31.7 to 33.6 GHz along with less than 3-dB axial ratio from 26.5 to 27.1 GHz and 31.9 to 33.1 GHz respectively. Orthogonal placement of ports introduces the concept of polarization diversity and decreases the coupling between ports by an amount of −25 dB. Good gain value (up to 7.0 dBi) and better value of diversity performance make the designed radiator applicable for 5 G millimeter-wave uses.

This paper presents the application of a substrate-integrated waveguide (SIW) for the design of a leaky-wave antenna (LWA). The antenna radiates through a wide slot in the top wall of the SIW structure in the forward direction. The effective width of the slot is varied by changing capacitances of two arrays of varactors connected between slot edges and inserted conducting strips. The radiation pattern of the antenna is by this way controlled by DC bias, which sets the capacitances of varactors. The maximum radiation direction in elevation can be varied within 35° by changing the DC bias from 2 to 12 V. This elevation angle is measured from the broad side direction perpendicular to the antenna substrate. The measured antenna characteristics are in accord with those predicted by simulation. The antenna can be simply fabricated by a planar circuit board technology.

This study proposed an effective and sustainable technique for the curing of carbon fiber reinforced polymers (CFRPs) using microwaves. The method involves applying a metallic resonance coating layer to envelop the CFRP composite’s surface. Next, the composite is positioned within a multi-mode cavity, which is used as an applicator, and is powered by four 250 W solid-state power amplifiers. To ensure precise control over the heating pattern and achieve uniform heating of the composite, a sophisticated control algorithm is developed. This algorithm can independently regulate the phase, power level, and frequency of each power amplifier. The experimental results confirm the effectiveness of this proposed approach in achieving precise control over the microwave-based curing process for CFRPs.

The design of low-profile Multiple-Input-Multiple-Output (MIMO) antennas for various 5G applications is a topic of huge interest in academia, research, and telecommunication sector. In this aspect, a compact and low-profile 5G MIMO antenna has been designed and analyzed for various 5G applications, specifically for the 24 GHz bands (24.25–24.45 GHz and 25.05–25.25 GHz) and local multipoint distribution system band (27.5–28.35 GHz) of the 5G spectrum. The proposed antenna structure is 20 × 20 × 1 mm3 in dimension. Two spade-shaped radiators composed of Copper (annealed) material are placed orthogonally to improve isolation and maintain signal diversity. Rogers RT 5880 is used as the material for substrate. The antenna exhibits a wide bandwidth of 21.5–28.5 GHz. The mutual isolation |S21| has been maintained ≤29 dB due to the insertion of a T-shaped parasitic strip in between the radiating elements. Novelty in design and superiority in performance has been observed when compared with related antenna categories.

The present work studies the design of a high impedance surface (HIS)-based bowtie antenna in the framework of characteristic mode analysis (CMA) and proposes the method of higher order mode suppression. A triangular-elliptical bowtie antenna operating in the frequency range of 1.6–6 GHz is designed. The radiating and higher order modes of the proposed antenna are identified using CMA, and an HIS structure is used to enhance the desired mode and to suppress the higher order mode in order to get high gain, good front-to-back ratio (FBR), and stable radiation characteristics. The final designed HIS-based bowtie antenna gives stable radiation patterns from 1.7 to 5.5 GHz with a maximum boresight gain of 10.5 dB. Also, gain from 6.5 to 12 dB and FBR from 8 to 18 dB are obtained in the operating bandwidth. The proposed antenna features the advantages of low profile, wideband and high boresight gain making it suitable for ground-penetrating radar applications.