To save content items to your account,
please confirm that you agree to abide by our usage policies.
If this is the first time you use this feature, you will be asked to authorise Cambridge Core to connect with your account.
Find out more about saving content to .
To save content items to your Kindle, first ensure email@example.com
is added to your Approved Personal Document E-mail List under your Personal Document Settings
on the Manage Your Content and Devices page of your Amazon account. Then enter the ‘name’ part
of your Kindle email address below.
Find out more about saving to your Kindle.
Note you can select to save to either the @free.kindle.com or @kindle.com variations.
‘@free.kindle.com’ emails are free but can only be saved to your device when it is connected to wi-fi.
‘@kindle.com’ emails can be delivered even when you are not connected to wi-fi, but note that service fees apply.
In this study, the effect of simple shearing on microstructure evolution and mechanical properties of 316L austenitic stainless steel were investigated. Two different shear strain routes were obtained by twisting cylindrical specimens in the forward and backward directions. The strain-induced martensite phase was effectively obtained by alteration of the routes. Formation of the martensite phase clearly resulted in significant hardening of the steel. Grain-size reduction and strain-induced martensitic transformation within the deformed structures of the strained specimens were characterized by scanning electron microscopy – electron back-scattered diffraction, X-ray diffraction, and the TEM-ASTAR (transmission electron microscopy – analytical scanning transmission atomic resolution, automatic crystal orientation/phase mapping for TEM) system. Significant numbers of twin networks were formed by alteration of the shear strain routes, and the martensite phases were nucleated at the twin interfaces.
Dynamic recrystallization (DRX) of 99.9999% aluminum single crystal at room temperature was examined under frictionless deformation mode. To exclude the self-heating of the specimen due to applied high strain, a microcrack that localizes the stress at a very small region was intentionally introduced by controlled local necking. For the in situ observation of DRX, a specially designed in situ microdeformation device was positioned inside an electron backscattered diffraction system chamber. Recrystallized grains showed relatively random texture and preferred growth direction. The subgrains with low-angle grain boundaries formed by dynamic recovery transformed into small grains with high-angle grain boundaries, acting as nuclei for discontinuous dynamic recrystallization and growing by further deformation. The DRX in pure aluminum can take place under frictionless tensile deformation conditions at room temperature, and the stress localization and high purity are key issues for the DRX of aluminum at room temperature.
Band contrast (BC) is a qualitative measure of electron back-scattered diffraction (EBSD), which is derived from the intensity of the Kikuchi bands. The BC is dependent upon several factors including scanning electron microscope measurement parameters, EBSD camera setup, and the specimen itself (lattice defect and grain orientation). In this study, the effective factors for BC variations and the feasibility of using BC variations for the quantification of microstructure evolutions have been investigated. In addition, the effects of the lattice defect and the grain orientation on the BC variations are studied. Next, a shear-deformed microstructure of 316L stainless steel, which contains nanosized grains and a large portion of twin boundaries, is revealed by BC map and histogram. Recovery and recrystallization of shear-deformed 316L stainless steel are displayed by BC variations during isothermal annealing at 700 and 800°C, respectively. It is observed that the BC turns bright as the shear-deformed crystal structure is recovered or recrystallized.
12Cr ODS steel samples were prepared by mechanical alloying of the metal powders with 20-30 nm Y2O3 particles followed by isostatic pressing, hot rolling and final heat treatment. Evolutions of oxide particles such as YTaO4 and YCrO3 after each fabrication step were investigated by using TEM with EDS. Crystallographic correlation between oxide particles and the matrix was investigated in a HIPped sample, and interactions between dislocations and oxide particles were observed in hot rolled or heat treated sample. Size distributions of oxide particles were measured by carbon replica samples and it was found that coarsening of oxide particles from 9 to 12 nm occurred during hot rolling process. Additional isothermal annealing at 1250 ˚C revealed that phase transformation of oxide particles from monoclinic YTaO4 to face centered cubic Y3TaO7 was observed.
Email your librarian or administrator to recommend adding this to your organisation's collection.