Hostname: page-component-848d4c4894-mwx4w Total loading time: 0 Render date: 2024-06-29T12:53:23.255Z Has data issue: false hasContentIssue false
  • English
  • Français

Investigation into the evolution of interface fracture toughness of thermal barrier coatings with thermal exposure treatment by wedge indentation

Published online by Cambridge University Press:  23 April 2020

Yue M. Wang ,
Wei X. Weng ,
Ming H. Chi ,
Bai L. Liu  and
Qiang Li
Yue M. Wang
Affiliation:
School of Materials Science and Engineering, Fuzhou University, Fuzhou 350116, China
Wei X. Weng
Affiliation:
School of Materials Science and Engineering, Fuzhou University, Fuzhou 350116, China
Ming H. Chi
Affiliation:
School of Materials Science and Engineering, Fuzhou University, Fuzhou 350116, China
Bai L. Liu
Affiliation:
School of Materials Science and Engineering, Fuzhou University, Fuzhou 350116, China
Qiang Li*
Affiliation:
School of Materials Science and Engineering, Fuzhou University, Fuzhou 350116, China
*
a)Address all correspondence to this author. e-mail: qli@fzu.edu.cn
Get access

Abstract

Thermal barrier coating is a high-temperature protective technology widely used in industrial gas turbines. However, the failure of coating peeling because of the generation of thermally grown oxide (TGO) at the interface during service hinders its further application. In this study, Raman spectroscopy and wedge indentation are used to determine the TGO residual stress and the interface energy release rate, respectively. The effect of TGO on the interfacial fracture toughness during the growth process was discussed. Raman spectroscopy test results show that the residual stress of TGO is about 0.5 GPa. Wedge indentation test results illustrate that high-temperature heat treatment could accelerate the interface degradation of thermal barrier coatings. Stress analysis and test research demonstrate that the microcracks induced by compressive stress of TGO will propagate with increasing heating time, ending with failure of barrier coatings.

Keywords

thermal barrier coatingsinterface fracturethermally grown oxide stress
Type
Article
Information
Journal of Materials Research , Volume 35 , Issue 13: Focus Section: Interactions of Shear Transformation Bands , 14 July 2020 , pp. 1715 - 1725
Check for updates
Copyright
Copyright © Materials Research Society 2020

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Padture, N.P.: Thermal barrier coatings for gas-turbine engine applications. Science 280, 296 (2002).Google Scholar
Tailor, S., Mohanty, R.M., and Doub, A.V.: Development of a new TBC system for more efficient gas turbine engine application. Mater. Today 3, 725–2734 (2016).Google Scholar
Rajendran, R.: Gas turbine coatings—An overview. Eng. Fail. Anal. 26, 355 (2012).CrossRefGoogle Scholar
Sadowski, T. and Golewski, P.: Multidisciplinary analysis of the operational temperature increase of turbine blades in combustion engines by application of the ceramic thermal barrier coatings (TBC). Comput. Mater. Sci. 50, 1326 (2011).CrossRefGoogle Scholar
Padture, N.P.: Advanced structural ceramics in aerospace propulsion. Nat. Mater. 15, 804 (2016).CrossRefGoogle ScholarPubMed
Sahith, M.S., Ga, G., and Kumara, R.S.: Development and analysis of thermal barrier coatings on gas turbine blades—A review. Mater. Today 5, 2746 (2018).Google Scholar
Aktaa, J., Sfar, K., and Munz, D.: Assessment of TBC systems failure mechanisms using a fracture mechanics approach. Acta Mater. 53, 4399–4413 (2005).CrossRefGoogle Scholar
Tzimas, E., Müllejans, H., Peteves, S.D., and Bressers, J.: Failure of thermal barrier coating systems under cyclic thermomechanical loading. Acta Mater. 48, 4699 (2000).CrossRefGoogle Scholar
Evans, A.G., Clarke, D.R., and Levi, C.G.: The influence of oxides on the performance of advanced gas turbines. J. Eur. Ceram. Soc. 28, 1405–1419 (2008).CrossRefGoogle Scholar
Lu, G.X., Hao, L.J., and Ye, F.X.: Thermal analysis and failure behavior of 8YSZ thermal barrier coatings under thermal cycling tests. Appl. Mech. Mater. 441, 91 (2013).CrossRefGoogle Scholar
Fauchais, P., Vardelle, M., and Goutier, S.: Latest researches advances of plasma spraying: From splat to coating formation. J. Therm. Spray Technol. 25, 1 (2017).Google Scholar
Kokini, K., Banerjee, A., and Thomas, A.T.: Thermal fracture of interfaces in precracked thermal barrier coatings. Mater. Sci. Eng., A 323, 70 (2002).CrossRefGoogle Scholar
Thurn, G., Schneider, G.A., Bahr, H.A., and Aldinger, F.: Toughness anisotropy and damage behavior of plasma sprayed ZrO2 thermal barrier coatings. Surf. Coat. Tech. 123, 147 (2000).CrossRefGoogle Scholar
Tong, J., Wong, K.Y., and Lupton, C.: Determination of interfacial fracture toughness of bone–cement interface using sandwich Brazilian disks. Eng. Fract. Mech. 74, 1904–1916 (2007).CrossRefGoogle ScholarPubMed
Elambasseril, J. and Ibrahim, R.N.: Determination of interfacial fracture toughness of coatings using circumferentially notched cylindrical substrate. Mater. Sci. Eng., A 529, 406 (2011).CrossRefGoogle Scholar
Liu, S.Y., Wheeler, J.M., Howie, P. R., and Zeng, X.T.: Measuring the fracture resistance of hard coatings. Appl. Phys. Lett. 102, 1–4 (2013).CrossRefGoogle Scholar
Sernicola, G., Giovannini, T., Patel, P., and Kermode, J.R.: In situstable crack growth at the micron scale. Nat. Mater. 8, 1–9 (2017).Google ScholarPubMed
Clarke, D.R., Levi, C.G.: Materials design for the next generation thermal barrier coatings. Annu. Rev. Mater. Res. 33, 383–417 (2003).CrossRefGoogle Scholar
Guo, H., Cui Y, Y., Peng, H., and Gong, S.K.: Improved cyclic oxidation resistance of electron beam physical vapor deposited nano-oxide dispersed β-NiAl coatings for Hf-containing superalloy. Corros. Sci. 52, 1440 (2010).CrossRefGoogle Scholar
Martena, M., Botto, D., Fino, P.: Modelling of TBC system failure: Stress distribution as a function of TGO thickness and thermal expansion mismatch. Eng. Fail. Anal. 13, 409 (2006).CrossRefGoogle Scholar
Ang, A.S.M., , C.C. Berndt: A review of testing methods for thermal spray coatings. Int. Mater. Rev. 59, 179 (2014).Google Scholar
Suzuki, K., Tanaka, K.: Spalling stress in oxidized thermal barrier coatings evaluated by X-Ray diffraction method. Mater. Sci. Forum. 490, 631 (2005).CrossRefGoogle Scholar
Chen, Y., Zhao, X., Dang, Y., and Xiao, P.: Characterization and understanding of residual stresses in a NiCoCrAlY bond coat for thermal barrier coating application. Acta Materi. 94, 1 (2015).CrossRefGoogle Scholar
Selçuk, A., Atkinson, A.: The evolution of residual stress in the thermally grown oxide on Pt diffusion bond coats in TBCs. Acta Mater. 51, 535 (2003).CrossRefGoogle Scholar
Heeg, B., Clarke, D.R.: Non-destructive thermal barrier coating (TBC) damage assessment using laser-induced luminescence and infrared radiometry. Surf. Coat. Tech. 200, 1298 (2005).CrossRefGoogle Scholar
Christensen, R.J., Lipkin, D.M., Clarke, D.R.: Nondestructive evaluation of the oxidation stresses through thermal barrier coatings using Cr3+ piezospectroscopy. Appl. Phys. Lett. 69, 3754 (1996).CrossRefGoogle Scholar
Yang, J., Wang, L., Li, D., and Zhong, X.H.: Stress Analysis and Failure Mechanisms of plasma-sprayed thermal barrier coatings. J. Therm. Spray. Techn. 26, 1 (2017).CrossRefGoogle Scholar
Lima, C.R.C., Dosta, S., Guilemany, J.M., and Clarke, D.R.: The application of photoluminescence piezospectroscopy for residual stresses measurement in thermally sprayed TBCs. Surf. Coat. Tech. 318, 147 (2016).CrossRefGoogle Scholar
Wang, X., Atkinson, A.: Piezo-spectroscopic mapping of the thermally grown oxide in thermal barrier coatings. Mater. Sci. Eng. A. 465, 49–58 (2007).CrossRefGoogle Scholar
Irwin, G.R.: Measuring plane-strains near the end of a crack traversing a plate. J. Appl. Mech. 24, 361 (1957).Google Scholar
Smiley, A.J., Pipes, R.B.: Rate effects on mode I interlaminar fracture toughness in composite materials. J. Compos. Mater. 21, 670 (1987).CrossRefGoogle Scholar
Qiao, X., Wang, Y.M., Weng, W.X., Li, Q.: Influence of pores on mechanical properties of plasma sprayed coatings: Case study of YSZ thermal barrier coatings. Ceram. Int. 44, 21564 (2018).CrossRefGoogle Scholar
Guo, S., Kagawa, Y.: Young’s moduli of zirconia top-coat and thermally grown oxide in a plasmasprayed thermal barrier coating system. Scripta Mater. 50, 1401–1406 (2004).CrossRefGoogle Scholar
Hutchinson, J.W., Mear, M.E., Rice, J.R.: Crack Paralleling an Interface Between Dissimilar Materials. J. Appl. Mech, 54, 828 (1987).CrossRefGoogle Scholar
He, J., Clarke, D.R.: Determination of the piezospectroscopic coefficients for chromium-doped sapphire. J. Am. Ceram. Soc. 78, 1347 (1995).CrossRefGoogle Scholar
Schlichting, K. W., Padture, N. P., Jordan, E. H., and Gell, M.: Failure modes in plasma-sprayed thermal barrier coatings. Mater. Sci. Eng. A. 342, 120 (2003).CrossRefGoogle Scholar
Clarke, D. R., Pompe, W.: Critical radius for interface separation of a compressively stressed film from a rough surface. Acta Mater. 47, 1749 (1999).CrossRefGoogle Scholar
Kim, S.S., Liu, Y.F., and Kagawa, Yutaka: Evaluation of interfacial mechanical properties under shear loading in EB-PVD TBCs by the pushout method. Acta Mater. 55, 3771 (2007).CrossRefGoogle Scholar
Clyne, T. W., Gill, S.C.: Residual stresses in thermal spray coatings and their effect on interfacial adhesive: A review of recent work. J. Therm. Spray. Techn. 5, 401 (1996).CrossRefGoogle Scholar
Ranjbar-Far, M., Absi, J., Mariaux, G., and Dubois, F.: Simulation of the effect of material properties and interface roughness on the stress distribution in thermal barrier coatings using finite element method. Mater. Design. 31, 772 (2010).CrossRefGoogle Scholar
Liu, D., Seraffon, M., Flewitt, P.E.J., and Simms, N.J.: Effect of substrate curvature on residual stresses and failure modes of an air plasma sprayed thermal barrier coating system. J. Eur. Ceram. Soc. 33, 3345 (2013).CrossRefGoogle Scholar