Hostname: page-component-77c89778f8-gq7q9 Total loading time: 0 Render date: 2024-07-20T02:43:34.905Z Has data issue: false hasContentIssue false
  • English
  • Français

Dense and smooth epitaxial BaTiO3 thin films by the dipping-pyrolysis process

Published online by Cambridge University Press:  31 January 2011

S. Kim ,
T. Fujimoto ,
T. Manabe ,
I. Yamaguchi ,
T. Kumagai  and
S. Mizuta
S. Kim
Affiliation:
National Institute of Materials and Chemical Research, Tsukuba, Ibaraki 305, Japan and Department of Chemical Engineering, Yosu National University, Yosu 550-250, Korea
T. Fujimoto
Affiliation:
National Institute of Materials and Chemical Research, Tsukuba, Ibaraki 305, Japan
T. Manabe
Affiliation:
National Institute of Materials and Chemical Research, Tsukuba, Ibaraki 305, Japan
I. Yamaguchi
Affiliation:
National Institute of Materials and Chemical Research, Tsukuba, Ibaraki 305, Japan
T. Kumagai
Affiliation:
National Institute of Materials and Chemical Research, Tsukuba, Ibaraki 305, Japan
S. Mizuta
Affiliation:
National Institute of Materials and Chemical Research, Tsukuba, Ibaraki 305, Japan
Get access

Abstract

Dense and smooth BaTiO3 thin films were prepared on SrTiO3 (100) substrates by the dipping-pyrolysis process using a mixed precursor solution of barium and titanium naphthenates. Combination effects of prefiring [at 150–450 °C in air or low oxygen partial pressure, p(O2)[ and final heat treatment [at 850 °C in air or low p(O2)[ on preparation of BaTiO3 thin films were examined. An epitaxial BaTiO3 thin film with a dense and smooth surface consisting of nanosized grains about 70 nm was prepared by prefiring under low p(O2) at 250 °C and final heat treatment under low p (O2) at 850 °C.

Type
Articles
Information
Journal of Materials Research , Volume 14 , Issue 2 , February 1999 , pp. 592 - 596
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Dimos, D., Annu. Rev. Mater. Sci. 25, 273 (1995).CrossRefGoogle Scholar
2.Glass, A. M., Science 235, 1003 (1987).CrossRefGoogle Scholar
3.Wills, L.A., Wessels, B. W., Richeson, D.S., and Marks, T. J., Appl. Phys. Lett. 60, 41 (1992).CrossRefGoogle Scholar
4.Kaiser, D. L., Vaudin, M. D., Lotter, L. D., Wang, Z.L., Cline, J. P., Hwang, C. S., Marinenko, R. B., and Gillen, J. G., Appl. Phys. Lett. 66, 2801 (1995).CrossRefGoogle Scholar
5.Terauchi, H., Watanabe, Y., Kasatani, H., Kamigaki, K., Terashima, T., and Bando, Y., J. Phys. Soc. Jpn. 61, 2194 (1992).CrossRefGoogle Scholar
6.Yano, Y., Iijima, K., Daitoh, Y., Terashima, T., Bando, Y., Watanabe, Y., Kasatani, H., and Terauchi, H., J. Appl. Phys. 76, 7833 (1994).CrossRefGoogle Scholar
7.Nose, T., Kim, H-T., and Uwe, H., J. Appl. Phys. 76, 5259 (1994).CrossRefGoogle Scholar
8.Srikant, V., Tarsa, E. J., Clarke, D. R., and Speck, J. S., J. Appl. Phys. 77, 1517 (1995).CrossRefGoogle Scholar
9.Kim, S., Hishita, S., Kang, Y. M., and Baik, S., J. Appl. Phys. 78, 5604 (1995).CrossRefGoogle Scholar
10.Fujimoto, K., Kobayashi, Y., and Kubota, K., Thin Solid Films 169, 249 (1989).CrossRefGoogle Scholar
11.Kim, D. H. and Kwok, H. S., Appl. Phys. Lett. 67, 1803 (1995).CrossRefGoogle Scholar
12.Kim, S., Manabe, T., Yamaguchi, I., Kumagai, T., and Mizuta, S., J. Mater. Res. 12, 1141 (1997).CrossRefGoogle Scholar
13.Manabe, T., Yamaguchi, I., Nakamura, S., Kondo, W., Kumagai, T., and Mizuta, S., J. Mater. Res. 10, 1635 (1995).CrossRefGoogle Scholar
14.Kim, S., Manabe, T., Yamaguchi, I., Kumagai, T., and Mizuta, S., Trans. Mater. Res. Soc. Jpn. 20, 636 (1996).CrossRefGoogle Scholar
15.Kim, S., Manabe, T., Yamaguchi, I., Kumagai, T., and Mizuta, S., Thin Solid Films 310, 199 (1997).CrossRefGoogle Scholar