In order to better understand the possible interactions between steel canisters and a claystone host rock, in this case the Callovo-Oxfordian rock (COx), the present study investigated in detail, under conditions relevant to high-level radioactive waste repositories (anoxic conditions, temperature of 90°C), the reactions between metallic iron and: (1) COx; (2) the clay fraction extracted from COx (CF); and (3) mixtures of CF with quartz, calcite, or pyrite. Batch experiments were then carried out in the presence of NaCl-CaCl2 background electrolyte, for durations of 1, 3, and 9 months. Solid and liquid end-products were characterized by a combination of techniques including liquid analyses, transmission and scanning electron microscopies, X-ray diffraction, N2 adsorption at 77 K, and Mössbauer spectroscopy. The interaction between CF and metallic iron appeared to proceed by means of pathways similar to those illustrated in previous studies on interactions between metallic iron and purified clays. In spite of the many similarities with previous studies, significant differences were observed between the behavior of COx and CF, particularly in terms of pH and Eh evolution, iron consumption, chemical composition of the neoformed particles, and textural evolution. Such differences demonstrate the important role played by non-clay minerals in reaction pathways. The addition of carbonates or pyrite to CF did not lead to significant change in reactivity. In contrast, under the conditions used in the present study, i.e. for relatively low iron:clay ratios, the presence of quartz strongly influenced reaction pathways. In the presence of quartz, magnetite was observed only in trace abundances whereas the amounts of magnetite were significant in experiments without quartz. Furthermore, filamentous serpentine particles with a small Al:Si ratio appeared which could develop from an FeSiAl gel that only forms in the presence of quartz. Considering that most clay rocks currently being considered for radioactive waste disposal contain significant amounts of quartz, the results obtained in the present study may be of significant interest for predicting the long-term behavior of clay barriers in such sites.

The equivalent diffuse double layer (DDL) thickness in clay-electrolyte systems is a very useful parameter for analyzing the engineering behavior of clays under different environmental conditions. The equivalent DDL thickness is generally assumed to be equal to the characteristic (Debye) length. The present work examined critically the applicability of characteristic length to define equivalent DDL thickness under various clay-surface and pore-fluid conditions. A critical analysis is presented of the changes in the equivalent DDL thickness and characteristic length under the influence of different clay-surface and electrolyte properties. The equivalent DDL thickness was found to be smaller than the characteristic length for a wide range of surface and pore-fluid parameters normally encountered in engineering practice. An accurate and simple power relationship was developed to predict the equivalent DDL thickness from the characteristic length, which is applicable to a wide range of clay-electrolyte systems.

Al-rich K-dioctahedral 1M and 1Md micas are abundant in sedimentary rocks and form a continuous compositional series from (Mg,Fe)-poor illite to aluminoceladonite through Mg-rich illite. The complexity and heterogeneity of chemical composition and structural features, as well as the lack of reliable diagnostic criteria, complicate the identification of these mica varieties. The objectives of the present study were to reveal the structural and crystal-chemical variability in the illite—aluminoceladonite series, and to define the composition ranges and identification criteria for the mica varieties in the series. A collection of illite and aluminoceladonite samples of various compositions was studied by X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) spectroscopy. Analysis of the relationships between unit-cell parameters and cation composition showed that the series includes three groups, (Mg,Fe)-poor illites, Mg-rich illites, and aluminoceladonites, each characterized by a unique combination of unit-cell parameter variation ranges. The distinctive features of aluminoceladonite are reduced values of csinβ and |ccosβ/a| in combination with b parameters that are smaller than those for Mg-rich illites, and slightly greater than those of (Mg,Fe)-poor illites. The compositional boundary between illite and aluminoceladonite occurs at Si = ~3.7 and Mg + Fe2+ = ~ 0.6 atoms per O10(OH)2.

A new approach to the interpretation of the FTIR spectroscopy data involving new relationships between band positons and cation composition of (Mg,Fe)-poor illites, Mg-rich illites, and aluminoceladonites provides additional diagnostic features that include the band positions and profile in the regions of Si—O bending, Si—O stretching, and OH-stretching vibrations. A sharp maximum from the AlOHMg stretching vibration at ~3600 cm−1, the presence of a MgOHMg stretching vibration at 3583–3585 cm−1, as well as characteristic band positions in the Si—O bending (435–, 468–472, and 509–520 cm−1) and stretching regions (985–1012 and 1090–1112 cm−1), are typical of aluminoceladonite.

Serpentinites, which contain high concentrations of Cr and Ni, weather easily into layer silicates and are therefore a possible source of metal contamination in soils. In the present study three soil profiles formed on serpentinites in a paddy field in eastern Taiwan were investigated to understand pedogenic clay-mineral transformations and to determine the relationship between the mineralogical characteristics and labile Cr and Ni in the soil. To this end, physicochemical analyses, micromorphology, X-ray diffraction, and Fourier transform infrared spectroscopy were employed. Serpentine and chlorite were the dominant minerals in the soil parent material, with smaller amounts of pyroxene, amphibole, and talc. Progressive weathering and the release of cations from the parent material resulted in the pedogenic formation of smectite, vermiculite, and interstratified chlorite-vermiculite, demonstrated by their presence in all Ap and AC horizons but their absence from the C horizons. Serpentine, pyroxene, amphibole, and talc are proposed to be transformed to low-charge smectite, while chlorite transformed to vermiculite through an interstratified chlorite-vermiculite phase. The surface soils were enriched in oxalate-extractable Fe relative to the subsoils, which was probably generated by the artificial flooding and draining of the paddy soils. The artificial flooding, which typically releases Fe, may also drive the observed partial hydroxyl interlayering of smectite and incomplete interlayer OH sheets of chlorite. Labile Cr and Ni (extracted with 0.1 N HCl) ranging from 4.7 to 26.8 mg kg−1 and from 56 to 365 mg kg−1, respectively, increased significantly toward the surface soil, consistent with weathering. The heavy metals released may pose a threat to the environment as well as to human health by entering the food chain.

Talc is an important industrial mineral with a broad range of applications. Particle size and crystal structure have a significant influence on the potential uses. The present study examined the influence of grinding and ultrasound treatment on talc from a new deposit, Gemerská Poloma, in Slovakia. The general knowledge that grinding produces progressive structural disorder leading to amorphization, whereas sonication has a negligible effect on the talc crystal structure, was confirmed by X-ray diffraction (XRD), infrared (IR) spectroscopy, and transmission electron microscopy (TEM). Partial reduction of particle size along with delamination was observed by XRD after sonication, low-angle laser light scattering (LALLS), scanning electron microscopy (SEM), and TEM. The specific surface area (SSA) increased slightly after prolonged sonication, but grinding initially caused a rapid increase in SSA followed by a drastic decrease after prolonged grinding time of up to 120 min which was attributed to the aggregation of amorphized talc. Sonication and grinding had different influences on the thermal behavior of the talc studied. Sonication decreased slightly the dehydroxylation temperature, whereas grinding added a significant mass loss at low temperature, arising from the dehydration of hydrated Mg cations released from the talc structure during amorphization. The initial high whiteness value of talc decreased slightly after grinding or sonication. Thermogravimetry was suggested as a useful tool to track and predict changes in the talc structure upon sonication and grinding.

The application of ceramic membranes is limited by the high cost of raw materials and the sintering process at high temperatures. To overcome these drawbacks, the present study investigated both the preparation of ceramic membranes using cost-effective raw materials and the possibility of recycling the membranes for the treatment of oily wastewater. Ceramic membranes with a pore size of 0.29–0.67 μm were prepared successfully at temperatures as low as 1000–1100°C by a simple pressing route using lowcost base materials including diatomite, kaolin, bentonite, talc, sodium borate, and barium carbonate. The typical steady-state flux, fouling resistance, and oil-rejection rate of the low-cost virgin membranes sintered at 1000°C were 2.5 × 10−5 m3m−2s−1 at 303 kPa, 63.5%, and 84.1%, respectively, with a feed oil concentration of 600 mg/L. A simple burn-out process of the used membranes at 600°C in air resulted in >95% recovery of the specific surface area (SSA) of the virgin membranes, a significantly increased steady-state flux, decreased fouling resistance, and increased oil-rejection rate. The typical steady-state flux, fouling resistance, and oil-rejection rate of the low-cost ceramic membrane sintered at 1000°C and subsequently heat treated at 600°C for 1 h in air after the first filtration were 5.4 × 10−5 m3m−2s−1 at 303 kPa, 27.1%, and 92.9%, respectively, with a feed oil concentration of 600 mg/L. The present results suggest that the low-cost ceramic membranes used for oily wastewater filtration can be recycled by simple heat-treatment at 600°C in air. As the fouling resistance of the low-cost ceramic membranes decreased with a decrease in pore size, the preferred pore size of the membranes for oily wastewater filtration is <0.4 μm.

Electro-osmotic consolidation is considered to be an efficient technique for dewatering and consolidation of soft soil. In the present study, four experiments were conducted on a Na-rich bentonite using two reactive electrodes (copper and iron) and two inert electrodes (graphite and stainless steel) to study the transport and exchange behavior of ions during electro-osmotic consolidation. The results showed that the changes in pH and ion contents were limited to the zone close to the electrode due to the buffering capacity of bentonite and the significant reduction in electric current density. The ion concentration profiles indicated that Na+ ions were largely responsible for carrying the pore water to the cathode. The reactive electrodes are better at transporting Na+ ions and therefore induce better drainage than inert electrodes. Ion-exchange reactions occurred between the Cu2+ and Fe2+/Fe3+ ions released and pre-existing Na+ ions in the electrical double layer, causing decreased water adsorption capacity and plasticity index. The swelling and shrinkage characteristics of the bentonite were thus reduced, and electroosmotic consolidation may therefore provide a new way to improve the stability of expansive soils and slopes.

Imogolite is usually formed by means of a three-step process involving the use of large amounts of water with long crystallization times and low yields, preventing large-scale synthesis. These drawbacks can be overcome by synthesis in the presence of fluoride, an approach which has been demonstrated to be suitable for the synthesis of other phyllosilicates. In the present study, the nature of the Al and Si sources, the Al/Si molar ratio, the volume of H2O for the redispersion of the gel after desalination, the F/Si molar ratio, as well as the crystallization temperature and time have been varied to investigate their role in the crystallization of imogolite. The structural properties of the as-synthesized samples were characterized by X-ray diffraction, infrared spectroscopy, and 29Si, 27Al, and 19F magic angle spinning nuclear magnetic resonance spectroscopy. The results show that the imogolite nanotubes can be prepared with high yields (>55%) from AlCl3·6H2O and Na4SiO4 aqueous solutions with an Al/Si molar ratio of 2.5, addition of HF for a F/Si molar ratio of 0.1–0.2, and 4 days of crystallization at 98°C.

Bentonite and iron metals are common materials proposed for use in deep-seated geological repositories for radioactive waste. The inevitable corrosion of iron leads to interaction processes with the clay which may affect the sealing properties of the bentonite backfill. The objective of the present study was to improve our understanding of this process by studying the interface between iron and compacted bentonite in a geological repository-type setting. Samples of MX-80 bentonite samples which had been exposed to an iron source and elevated temperatures (up to 115°C) for 2.5 y in an in situ experiment (termed ABM1) at the Äspö Hard Rock Laboratory, Sweden, were investigated by microscopic means, including scanning electron microscopy, μ-Raman spectroscopy, spatially resolved X-ray diffraction, and X-ray fluorescence.

The corrosion process led to the formation of a ~100 μm thick corrosion layer containing siderite, magnetite, some goethite, and lepidocrocite mixed with the montmorillonitic clay. Most of the corroded Fe occurred within a 10 mm-thick clay layer adjacent to the corrosion layer. An average corrosion depth of the steel of 22–35 μm and an average Fe2+ diffusivity of 1–2 × 10−13 m2/s were estimated based on the properties of the Fe-enriched clay layer. In that layer, the corrosion-derived Fe occurred predominantly in the clay matrix. The nature of this Fe could not be identified. No indications of clay transformation or newly formed clay phases were found. A slight enrichment of Mg close to the Fe—clay contact was observed. The formation of anhydrite and gypsum, and the dissolution of some SiO2 resulting from the temperature gradient in the in situ test, were also identified.

Sedimentary and diagenetic processes control the distribution of clay minerals in sedimentary basins, although these processes have seldom been studied continuously in continental sedimentary basins. The Songliao Basin, northeast China, is a large continental, petroleum-bearing basin, and provides a unique study site to understand the sedimentary and diagenetic processes that influence clay assemblages. In this paper, the clay mineralogy of a 2500 m-thick Late Cretaceous (late Turonian to Maastrichtian) terrestrial sedimentary succession (SK-1s and SK-1n cores), retrieved by the International Continental Scientific Drilling Program in the Songliao Basin, was examined. The objective was to determine the diagenetic and paleoenvironmental variations that controlled the formation of clay mineral assemblages, and to determine the thermal and paleoenvironmental evolution of the basin. The results from both cores show that illite is ubiquitous through the succession, smectite is frequently encountered in the upper strata, and ordered mixed-layer illite-smectite (I-S), chlorite, and kaolinite are abundant in the lower strata. Burial diagenesis is the primary control on the observed decrease of smectite and increasing illite, I-S, and chlorite with depth. Observations of clay-mineral diagenesis are used to reconstruct the paleotemperatures and maximum burial depths to which the sediments were subjected. The lowermost sediments could have reached a maximum burial of ~1000 m deeper than today and temperatures ~50°C higher than today in the latest Cretaceous. The transition of smectite to I-S in the SK-1 cores and the inferred paleotemperatures provide new constraints for basin modeling of oil maturation at elevated temperatures in the Songliao Basin. Authigenic kaolinite and smectite are enriched in sandstones with respect to the coeval mudstones from the SK-1n core, as a result of early diagenesis with the participation of primary aluminosilicates and pore fluids. In the upper part of both SK-1 cores, variations in smectite and illite were controlled primarily by paleoenvironmental changes. Increases in smectite and decreases in illite from the late Campanian to Maastrichtian are interpreted as resulting from increasing humidity, a conclusion consistent with previous paleoenvironmental interpretations.

Page 276: Change the average value of Cr in the ophiolitic rocks from 1850 ppm to 2530 ppm.

Ceramic clays are among the most complicated of ceramic systems because of the very intricate relationship between the behavior of minerals during ceramic processing and their modifications during heating. A major challenge is to predict the phase changes in clay ceramics. The aims of this study were to establish reference data of ceramic products that can be formed based on the mineralogical compositions of the local raw materials. These data, in turn, can be compared with archeological ceramics in order to study their origins.

The mineralogical compositions and modifications during firing (550–1100°C under oxidizing conditions) of seven clayey materials sampled from the main clay deposits of northern Morocco were evaluated by X-ray powder diffraction. Two groups of clays were distinguished according to the type of neoformed high-temperature minerals: non-calcareous clays and calcareous clays. For the non-calcareous raw materials, spinel was produced at 950°C. Cristobalite and mullite were formed at temperatures in excess of 1000°C from clays that contain illite, kaolinite, and chlorite. In clays containing vermiculite and large amounts of chlorite, hematite was formed at temperatures in excess of 950°C. Firing of calcareous clays at temperatures >950°C yielded Ca-silicates (diopside, gehlenite and wollastonite), spinel, cristobalite, hematite, and feldspars. Mullite may also form in the calcareous clay products when the carbonate content exceeds 10%.

The conventional methods of direct bromination of organic compounds with elemental bromine have several major drawbacks such as handling difficulty, corrosive effect, and toxicity, in addition to over-bromination and problems with isolation of products from the reaction mixture. Supported catalysts and reagents have become popular in the synthesis of organic chemicals over recent decades because they have overcome almost all of the drawbacks noted above. In the present study, a new clay polymer nanocomposite (CPN)-supported brominating agent was prepared from montmorillonite (Mnt) and styrene-co-vinyl pyridinium polymer. The reagent was obtained by the direct interaction of a two-fold excess of poly(styrene-co-N-methyl-4-vinylpyridinium) bromide with Na-montmorillonite (NaMnt) through ion exchange between Na+ of the NaMnt and pyridinium ions in the copolymer to provide CPN3 with free methylpyridinium bromide side chains. The structure of the CPN3 prepared was characterized by infrared spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Treatment of the CPN3 with bromine using the bromide ions which remained led to the perbromide-supported reagent, CPN4. The activity of the resulting CPN4 brominating reagent was examined through direct bromination of some alkenes, arenes, and carbonyl compounds and compared with the effectiveness of a crosslinked polymeric perbromide reagent. The yields obtained from application of the reagent were moderate to excellent. The advantages of this reagent, such as stability at room temperature, ease of regeneration from the polymeric by-product, and the yields of the brominated products, confirm the viability of using a CPN-supported brominating agent as a reactive reagent in organic chemistry synthesis.