Hostname: page-component-848d4c4894-v5vhk Total loading time: 0 Render date: 2024-06-27T03:33:53.034Z Has data issue: false hasContentIssue false
  • English
  • Français

Experimental and numerical failure analysis of bolted joints in CFRP woven laminates

Published online by Cambridge University Press:  04 July 2016

N. Andréasson ,
C. P. Mackinlay  and
C. Soutis
N. Andréasson
Affiliation:
Department of AeronauticsImperial College of Science, Technology and Medicine , London, UK
C. P. Mackinlay
Affiliation:
Department of AeronauticsImperial College of Science, Technology and Medicine , London, UK
C. Soutis
Affiliation:
Department of AeronauticsImperial College of Science, Technology and Medicine , London, UK
Get access Rights & Permissions [Opens in a new window]

Abstract

The purpose of a joint is to transfer load between the two parts being joined. As a result of this load transfer there will be a stress variation in the components in the joint region, as well as stresses in the joining medium (fasteners or adhesive). In fhjs work, the stress results of a two-dimensional finite element (FE) analysis are used to understand failure modes of a bolted joint in low-temperature cure carbon fibre reinforced plastic (CFRP) woven laminates loaded in tension, and to predict the bearing strength. Good agreement with experimentally observed damage modes and strengths is achieved with, in some cases, a difference of less than 10%.

Type
Research Article
Information
The Aeronautical Journal , Volume 102 , Issue 1018 , December 1998 , pp. 445 - 450
Copyright
Copyright © Royal Aeronautical Society 1998 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Collings, T.A. The strength of bolted joints in multi-directional CFRP laminates, Composites, 1977,8,1977, pp 43-54.Google Scholar
2. Collings, T.A. On the bearing strengths of CFRP laminates, Composites, 1982,13, pp 241–252.Google Scholar
3. Wong, C.M.S. and Matthews, F.L. A finite element analysis of single and two-hole bolted joints in fibre reinforced plastic, J Comp Mater, 1981,15, pp 481–491.Google Scholar
4. Matthews, F.L., Wong, C.M.S. and Chrysafitis, C. Stress distribution around a single bolt in fibre reinforced plastic, Composites, 1982,13, pp 316–322.Google Scholar
5. Kretsis, G. and Matthews, F.L. The strength of bolted joints in glass fibre/epoxy laminates, Composites, 1985,16, pp 92–105.Google Scholar
6. Agarwal, B.L. Static strength prediction of bolted joints in composite materials, AIAA J, 1980,18, pp 1371–1375.Google Scholar
7. Zhang, K. and Ueng, C.E.S. Stresses around a pin-loaded hole in orthotropic plates, J Comp Mater, 1984,18, pp 119–143.Google Scholar
8. Smith, P.A. Aspects of die Static and Fatigue Behaviour of Composite Laminates, Including Bolted Joints, PhD Thesis, Cambridge University Engineering Department, UK, 1985.Google Scholar
9. Eriksson, L.I. Contact stresses in bolted joints of composite laminates, Composite Structures, 1986, 6, pp 57–75.Google Scholar
10. Smith, P.A., Pascoe, K.J., Polak, C. and Stround, D.O. The behaviour of single-lap bolted joints in CFRP laminates, Composite Structures, 1986,6, pp 41–55.Google Scholar
11. Hyer, M.W., Klang, E.C. and Cooper, D.E. Effects of pin elasticity, clearance and friction on the stresses in a pin-loaded orthotropic plate, J Comp Mater, 1987, 21, pp 190–206.Google Scholar
12. Chen, W.H., Lee, S.S. and Yeh, J.T. Three-dimensional contact stress analysis of a composite plate with a bolted joint, Composite Structures, 1995,30, pp 287–297.Google Scholar
13. Camanho, P.P. and Matthews, F.L. Stress analysis and strength prediction of mechanically fastened joints in FRP: a review. Composites (Part A), 1997, 28A, pp 529–547.Google Scholar
14. Kinsey, A., Saunders, D.E.J, and Soutis, C Post-impact compressive behaviour of low temperature curing woven CFRP laminates, Composites, 1995,26, (4), pp 661–667.Google Scholar
15. Curtis, P.T. CRAG test methods for the measurement of the engineering properties of fibre reinforced plastics, RAE Technical Report 88012, 1988.Google Scholar
16. Hart-Smith, L.J. Mechanically-fastened joints for advanced composites—phenomenological considerations and simple analyses, In: Proc 4th Conf On Fibrous Composites in Structural Design, San Diego, USA, 1978, pp 543.Google Scholar
17. Lekhnitskii, S.G. Theory of Elasticity of an Anisotropic Elastic Body, Holden-Day, San Fransisco, USA, 1963.Google Scholar
18. Whitney, J.M. and Nuismer, R.J. Stress fracture criteria for laminated composites containing stress concentrations, J Comp Mater, 1974,8, pp 253–265.Google Scholar
19. Andréasson, N. Tensile Strength of Bolted Joints in Woven CFRP Laminates, MSc Thesis, Department of Aeronautics, Imperial College, London, UK, 1996.Google Scholar
20. De Jong, T. Stresses around pin-loaded holes in composite materials, In: Proc IUTAM Symposium on Mechanics of Composite Materials, Virginia Polytechnic, Blacksburg, Virginia, USA, Hashin, Z. et al (Eds), Pergamon Press, 1982, pp 339–353.Google Scholar
21. Tsai, S.W. Composites Design, 4th Edition, Think Composites, 1988.Google Scholar