Introduction
Trace levels of impurity have been shown to affect the dielectric behaviour of ice grown from dilute solutions in the laboratory (Reference Camplin, Glen and ParenCamplin and others, 1978; Reference Gross, Hayslip and HoyGross and others, 1978; Reference Takei and MaenoTakei and Maeno, 1987). No similar study has been made on the ice of polar ice sheets. Dielectric measurements (Paren, Reference Paren, Whalley, Jones and Gold1973; Reference Fitzgerald and ParenFitzgerald and Paren, 1975; Reference Glen and ParenGlen and Paren, 1975), undertaken at the time that the technique of radar sounding (RES) ice sheets at HF-VHF was being developed, showed a general uniformity of behaviour, so that, for RES purposes, polar ice had a simple well defined temperature-dependent response (Reference Fitzgerald, Paren and GlenFitzgerald and others, 1977). The discovery during RES flights of internal reflections from deep within the ice sheets (Reference Robin, Evans and BaileyRobin and others, 1969; Harrison, Reference Harrison1973; Gudmandsen, Reference Gudmandsen1975) implied there to be a source of variability in the ice. The most likely source of this variability is from changes in the dielectric conductivity of ice (Reference Paren, Robin and deParen and Robin, 1975; Millar, Reference Millar1981). Reynolds (Reference Reynolds1985) showed there were marked dielectric differences between the ice recovered from the cold interiors of polar regions and the ice of the warmer coastal areas. A chemical explanation of these differences was possible: there is a large increase in concentrations of impurities at coasts compared with more continental areas (Heron, Reference Herron1982; Legrand, Reference Legrand, Petit and Korotkevich1987). Dramatic changes in ice chemistry are usually associated with large discrete events such as volcanic eruptions (Hammer, Reference Hammer1980, Maccagnan and others, 1981) or changes in climate between ice ages and interglacials (Reference Legrand, Lorius, Barkov and PetrovLegrand and others, 1988).
To date the only physical technique sensitive to the chemical composition of the solid ice is the rapid stratigraphic analysis of ice cores by the electrical conductivity measurement (ECM) method developed by Hammer (Reference Hammer1980). This powerful technique has identified acidic deposition following volcanic eruptions, and also annual cycles of acidity in Greenland precipitation. The technique requires a freshly cut ice surface over which two electrodes (1.5 mm2) a few cm apart are drawn with a potential of about 1 kV between them. The current flowing between the electrodes is sensitive to the acid content and the thermal history of the ice (Hammer, Reference Hammer1980; Reference Maccagnan, Barnola, Delmas and DuvalMaccagnan and others, 1981), but is independent of the salt concentration (Hammer, Reference Hammer1980). For repeatable current measurements a new surface must be prepared.
Dielectric Profiling (Dep) Technique
The DEP technique (Reference Moore and ParenMoore and Paren, 1987) has one major advantage over ECM profiling; it is that no direct contact needs to be made between ice and electrodes, so that the core remains in good condition for any further analysis. In addition, the method is non-destructive and gives repeatable results with an exciting voltage of only 1V.
The Dolleman Island core was measured with a resolution of 5 cm down its 130 m length. Dielectric parameters are measured at 42 frequencies between 20 Hz and 300 kHz. A 1 m length of core can be measured in 20 minutes. The ice within a protective polythene sleeve behaves as an electrical blocking layer system. Formulae are available (Reference Gross, Hayslip and HoyGross and others, 1980) for extracting the intrinsic ice behaviour from that of the composite blocking system, but a critical parameter, the size of the variable gap between the electrode and the ice, is not accurately known. We find it satisfactory to use the dielectric parameters of the composite system alone to relate to the chemical stratigraphy. At LF (∼100 kHz), the conductivity of the composite system is within a few per cent of that intrinsic to the ice, and approximates well to the conductivity of ice in the RES frequency range. This conductivity, σ∞, is at a frequency much higher that the relaxation frequency, fr, of the dominant dielectric dispersion of the blocking layer system. Both σ∞ and fr display a good correlation with chemistry despite noise from the effect of the variable electrode/polythene/ice contact. The effects of the blocking layer mean that fr cannot be directly compared with values for the relaxation frequency of ice. The blocking layer also leads to a higher experimental scatter in the value of fr than in σ∞. We have found that for the Dolleman core fr is a useful additional parameter to σ∞; however, its dependence on factors that are not intrinsic to the ice may mean that fr has limited value in the dielectric analysis of other cores.
Comparison Of Dep and Chemical Data
The only ice core so far studied both dielectrically (Moore, Reference Moore1988) and chemically is the 130 m core from Dolleman Island (70°35’S, 60°55’W; elevation 400 m, mean annual temperature −17°C). A continuous 45 m section from between 26 m and 71 m depths has been analyzed for Na+, Mg2+, Cl−,
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary:20170926041310858-0545:S0260305500008569:S0260305500008569_eqn1.gif?pub-status=live)
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary:20170926041310858-0545:S0260305500008569:S0260305500008569_eqn2.gif?pub-status=live)
The average chemical compositon of the core in units of μeql−1 is Na+: 11.2, Mg2+: 2.7, Cl−: 14.64,
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary:20170926041310858-0545:S0260305500008569:S0260305500008569_eqn1a.gif?pub-status=live)
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary:20170926041310858-0545:S0260305500008569:S0260305500008569_eqn2a.gif?pub-status=live)
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary-alt:20170926134346-65718-mediumThumb-S0260305500008569_eqn5.jpg?pub-status=live)
which represents the total marine cation concentration in the ice. The total anion concentration has a mean value of 19.95 μeql−1 and is given by:
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary-alt:20170926134346-84590-mediumThumb-S0260305500008569_eqn6.jpg?pub-status=live)
The total concentration of strong acid in the ice (mean value 5.36 μeql−1), made up of contributions from HCl, H2SO4 and HNO3 is given by:
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary:20170926041310858-0545:S0260305500008569:S0260305500008569_eqn7.gif?pub-status=live)
This method of calculating acid concentrations has been verified by comparison with [H+] measured directly by acid titration on 63 samples (Fig. 1).
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary-alt:20170926134346-53952-mediumThumb-S0260305500008569_fig8g.jpg?pub-status=live)
Fig. 1. A comparison of the measured [H+] found by acid titration and calculated [H+] found from the difference between total anions and marine cations for 63 samples from the Dolleman core. The anions are averaged over 10 cm intervals to match the DEP sample width (about 5 samples per year accumulation).
The chemical composition of the Dolleman core is complicated and will be discussed elsewhere. There are localized variations in ionic ratios from those of normal sea water, which makes the calculation of each individual strong acid concentration difficult to determine accurately. However, it is clear than in general H2SO4 is the dominant acid. Because of the difficulty of separating out the individual acid concentrations, it has not been possible to examine any differences in their effects on the dielectric behaviour. Therefore, the dielectric behaviour has been studied as a function of the “salt” and “acid” parameters. A non-linear regression analysis of the dependence of the dielectric parameters on the chemical parameters yielded functions with linear exponents:
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary-alt:20170926134346-81323-mediumThumb-S0260305500008569_eqn9.jpg?pub-status=live)
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary-alt:20170926134346-16580-mediumThumb-S0260305500008569_eqn10.jpg?pub-status=live)
The dependence of anions on the dielectric parameters, however, produced a non-linear fit:
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary-alt:20170926134346-05189-mediumThumb-S0260305500008569_eqn11.jpg?pub-status=live)
The units of σ∞ are μSm−1. those of fr are Hz and the chemical quantities are μeql−1. Relation (4) accounts for 86.7% of the variance of [anions]. The total anion concentration predicted from Equation (4) can be compared with the measured total anion concentration in Figure 1. It can be seen from Equations (2) and (3) that the salt and acid produce quite different effects on the dielectric parameters, with a given amount of acid producing over three times the change in σ∞ produced by the same amount of salt.
Although the dependence of the dielectric parameters on the chemical species can be expressed as simple linear relationships, the inverse relationship for anions is non-linear in the dielectric variables. This probably results from the way in which salt and acid display annual cycles that are out of phase. Thus the dependence of [anions] is probably dependent on the individual ice core chemistry, whilst the σ∞ and fr relations should be applicable to any ice core at the same temperature.
Discussion
The coefficient of acid in Equation (2) can be compared with that expected from the model of Wolff and Paren (Reference Wolff and Paren1984). This model is based on the localization of acids at three grain boundaries in the liquid state. Acids then contribute the d.c. term to σ∞. Recent work by Mulvaney and others (Reference Mulvaney, Wolff and Oates1988) supports the localization of sulphur (chiefly H2SO4) at triple grain junctions in Dolleman ice. The acid is sufficiently concentrated to remain liquid at temperatures above −70°C, forming a network of conducting veins in the ice. The model predicts a linear dependence of σ∞ on [acid] with a constant of proportionality dependent on the relative concentrations of each acid For the Dolleman core the dominant acid is H2SO4 which at −22°C would give a constant of proportionality of 1.41. HCl and HNO3 produce higher constants around 2.4; we would therefore expect a value close to that observed in Equation (2) of 1.43. The dependence of fr on [acid] shown in Equation (3) is not easily explainable by the model of Wolff and Paren since no dispersion is predicted for the acid veins in the AF-LF frequency range. The observed dependence of fr is probably an artifact of the composite blocking layer system, rather than a real variation in intrinsic ice relaxation frequency. However, the effect could be a result of some acid component making a contribution to the dielectric conductivity rather than the d.c. conductivity. The nature of the salt dependence in Equations (2) and (3) can be explained by the generation of a Bjerrum defect by every one or two salt ions present in the ice (Moore, unpublished). This implies that, in contrast to the acid impurity, a large fraction of the salt impurity is incorporated into the ice lattice.
The σ∞/acid relationship observed for Dolleman ice can be compared with the relationship given by Hammer (1980)
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary-alt:20170926134346-50307-mediumThumb-S0260305500008569_fig14g.jpg?pub-status=live)
Fig. 2. A comparison of the measured total anion (Cl− +
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary:20170926041310858-0545:S0260305500008569:S0260305500008569_eqn1b.gif?pub-status=live)
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary:20170926041310858-0545:S0260305500008569:S0260305500008569_eqn2b.gif?pub-status=live)
for the dependence of [H+] on the ECM current, i, for the Greenland ice at -14°C:
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary:20170926041310858-0545:S0260305500008569:S0260305500008569_eqn15.gif?pub-status=live)
where the units of [H+] are μΜ and i are μΑ. Legrand and others (Reference Legrand1987) found a similar relationship for two Antarctic sites but with exponents of 1.6 and 2.4, and an activation energy of 0.25 eV. Using this activation energy the relationship between ECM i and acidity at -22°C is approximately:
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary:20170926041310858-0545:S0260305500008569:S0260305500008569_eqn16.gif?pub-status=live)
Schwander and others (Reference Schwander, Neftel, Oeschger and Stauffer1983) found an empirical linear relationship between ECM current and conductivity that depended on the area of the ECM electrodes and the potential applied. For Hammer’s electrode geometry this gives σ ∼0.57 i. Thus there appears to be a difference in the functional relationship between acidity and ECM conductivity, and that with DEP conductivity, that has yet to be explained.
The ECM technique has been found to be very useful in the identification of sections of ice cores which contain high levels of acidity, but the technique is insensitive to neutral salt concentrations. DEP is sensitive to both types of impurity but has lower resolution than ECM. An effective method of estimating the neutral salt contribution of a core with similar chemistry to that of Dolleman Island would be to combine Equations (1), (4) and (5) to produce an equation such as:
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary-alt:20170926134346-95236-mediumThumb-S0260305500008569_eqn17.jpg?pub-status=live)
assuming the electrical measurements were all made at -22°C. We suggest a more universal relationship results from combining Equations (2) and (5), avoiding the anion relationship (Equation (4)), possibly specific to Dolleman Island alone, giving:
![](https://static.cambridge.org/binary/version/id/urn:cambridge.org:id:binary-alt:20170926134346-47355-mediumThumb-S0260305500008569_eqn18.jpg?pub-status=live)
Using the latter equation (Equation (7)) it should be possible to rapidly analyze an ice core using only electrical techniques to determine both total acid concentrations and neutral salt concentrations.
Acknowledgements
J.C. Moore wishes to acknowledge the generosity of the Transantarctic Association who provided travel funds for presentation of this paper at the Seattle symposium.
We thank A. Reid, E. Suttie and E. Wolff for some of the chemical analyses.