Hostname: page-component-77c89778f8-7drxs Total loading time: 0 Render date: 2024-07-17T06:31:03.779Z Has data issue: false hasContentIssue false
  • English
  • Français

Optimal Discrete Adjustments for Short Production Runs

Published online by Cambridge University Press:  27 July 2009

Scott A. Vander Wiel
Scott A. Vander Wiel
Affiliation:
AT&T Bell Laboratories, Murray Hill, New Jersey 07974
Get access Rights & Permissions [Opens in a new window]

Abstract

Diameter measurements on successive metal hubs from a machining operation are modeled using a random walk with observation error and linear drift corresponding to tool wear. After producing and measuring a hub, the depth of the cutting tool on the lathe can be adjusted in integer multiples of 0.0001 inches. How should the tool be adjusted?

An optimal discrete adjustment strategy is derived assuming that the lathe automatically corrects for deterministic tool wear. The objective is to minimize expected run costs proportional to the sum of squared diameter deviations from a target plus fixed charges for manual tool adjustments. The optimal strategy makes no manual adjustment if an estimate of the process mean is near target. Otherwise, an adjustment is made to return the estimated mean as near to target as possible within the adjustment resolution.

The region where no adjustments are made widens near the end of the production run where adjustments have only short-term impact. The region converges as the number of remaining periods increases. Plots of expected run costs show that the extra cost of discreteness is small at high resolution but is substantial when the adjustment grid is coarse.

Type
Research Article
Information
Probability in the Engineering and Informational Sciences , Volume 10 , Issue 1 , January 1996 , pp. 119 - 151
Copyright
Copyright © Cambridge University Press 1996

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Bather, J.A. (1963). Control charts and the minimization of costs. Journal of the Royal Statistical Society, Series B 25: 49–70.Google Scholar
2.Box, G.E.P. & Jenkins, G.M. (1963). Further contributions to adaptive quality control: Simultaneous estimation of dynamics: Non-zero costs. Bulletin of the International Statistical Institute 34: 943–974.Google Scholar
3.Box, G. & Kramer, T. (1992). Statistical process monitoring and feedback adjustment—A discussion. Technometrics 34: 251–267 (disc: pp. 268–285).CrossRefGoogle Scholar
4.Box, G. & Luceno, A. (1994). Selection of sampling interval and action limit for discrete feedback adjustment. Technometrics 36: 369–378.CrossRefGoogle Scholar
5.Crowder, S.V. (1986). Kalman filtering and statistical process control. Ph.D. thesis, Iowa State University, Ames.Google Scholar
6.Crowder, S.V. (1992). An SPC model for short production runs:. Minimizing expected cost. Technometrics 34(1): 64–73.CrossRefGoogle Scholar
7.Harvey, A.C. (1989). Forecasting, structural time series models and the Kalman filter. Cambridge: Cambridge University Press.Google Scholar
8.Jensen, K.L. & Vardeman, S.B. (1993). Optimal adjustment in the presence of deterministic process drift and random adjustment error. Technometrics 35(4): 376–389.CrossRefGoogle Scholar
9.Kramer, T.T. (1989). Process control from an economic point of view. Ph.D. thesis. University of Wisconsin, Madison.Google Scholar
10.Meinhold, R.J. & Singpurwalla, N.D. (1983). Understanding the Kalman filter. The American Statistician 37(2): 123–127.Google Scholar
11.Taguchi, G. (1986). Introduction to quality engineering: Designing quality into products and processes. Tokyo: Asian Productivity Organization.Google Scholar
12.Tucker, W.T., Faltin, F.W., & Vander Wiel, S.A. (1993). Algorithmic statistical process control: An elaboration. Technometrics 35(4): 363–375.CrossRefGoogle Scholar