Hostname: page-component-848d4c4894-tn8tq Total loading time: 0 Render date: 2024-06-24T13:36:59.769Z Has data issue: false hasContentIssue false
  • English
  • Français

Wetting Behaviors of Sn-Based Solders on Cu and Pd Surfaces

Published online by Cambridge University Press:  21 February 2011

H. K. Kim ,
Y. Wang ,
A. Maheshwari  and
K. N. Tu
H. K. Kim
Affiliation:
Department of Materials Science and Engineering, University of California at Los Angeles, Los Angeles, CA 90095-1595
Y. Wang
Affiliation:
Department of Materials Science and Engineering, University of California at Los Angeles, Los Angeles, CA 90095-1595
A. Maheshwari
Affiliation:
Miniaturization Lab, Texas Inst. Inc., Temple, TX 76503-6102
K. N. Tu
Affiliation:
Department of Materials Science and Engineering, University of California at Los Angeles, Los Angeles, CA 90095-1595
Get access

Abstract

We have studied the surface morphology and wetting reaction of eutectic SnBi, eutectic SnPb, and pure Sn on Cu and Pd surfaces. In the case of Pd, the reactions were so fast that no quasi-equilibrium wetting angle could be measured. The compound formation has changed not only the interfaces but also the surfaces. Due to the formation of a reaction band outside the solder cap, the SnPb solder is no longer wetting the Cu surface but rather the Cu-Sn compound surface. In the wetting interface between eutectic SnPb and Cu, the morphology of the scallop-like Cu-Sn compound grains shows that we may not apply the classical model of layered compound growth to analyze the rate of soldering reactions.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 390: Symposium S – Electronic Packaging Materials Science VIII , 1995 , 183
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Tummala, R.R., Rymaszewski, E.J., Microelectronics Packaging Handbook (Van Nostrand Reinhold, New York, 1989).Google Scholar
2. Seraphim, D., Lasky, R., and Li, C.Y., Principles of Electronic Packaging (McGraw-Hill, New York, 1989).Google Scholar
3. Wild, R.N., Presentation at the National Center for Manufacturing Science Meeting on “Environmentally Conscious Manufacturing” (Owego, New York, July, 1993).Google Scholar
4. Vianco, P.T. and Frear, D.R., J. Metals 45(7),14 (1993).Google Scholar
5. Morris, J.W. Jr., Goldstein, J.L. Freer, and Mei, Z., J. Metals 45(7),25 (1993).Google Scholar
6. McCormack, M. and Jin, S., J. Metals 45(7), 36 (1993).Google Scholar
7. Stromswold, E.I., Pratt, R.E., and Quesnel, D.J., J. Elec. Mat. 23(10), 1047 (1994).Google Scholar
8. Kim, H.K., Liou, H.K., and Tu, K.N., J. Mater. Res. 10, 487 (1995).Google Scholar
9. Wang, Y., Kim, H.K., Liou, H.K., and Tu, K.N., Scripta Met. and Mat. (in press).Google Scholar
10. Onishi, M. and Fujibuchi, H., Trans. Japan Inst. Metal 16, 539 (1975).Google Scholar
11. Hansen, M., Constitution of Binary Alloys (McGraw-Hill, New York, 1958), p.610.Google Scholar
12. Wu, Y., Sees, J.A., Pouraghabagher, C., Foster, L.A., Marshall, J.L., Jacobs, E.G., and Pinizzotto, R.F., J. Electron. Mat. 22, 769 (1993).Google Scholar
13. Boettinger, W.J., Handwerker, C.A., and Smith, L.C., The Metal Science of Joining (TMS, Warrendale, PA, 1992), p. 183.Google Scholar
14. Kim, H.K., Liou, H.K., and Tu, K.N., Appl. Phys. Lett., 66, 2337 (1995).Google Scholar