Hostname: page-component-76fb5796d-45l2p Total loading time: 0 Render date: 2024-04-26T06:23:32.127Z Has data issue: false hasContentIssue false
  • English
  • Français

Tensile Testing of Fiber Reinforced Cementitious Composites

Published online by Cambridge University Press:  16 February 2011

Tahar El-Korchi ,
Houssam Toutanji ,
R. Nathan Katz ,
Gary L. Leatherman ,
Harald Lucas  and
Cornelia Demers
Tahar El-Korchi
Affiliation:
Worcester Polytechnic Institute, Worcester, MA. 01609
Houssam Toutanji
Affiliation:
Worcester Polytechnic Institute, Worcester, MA. 01609
R. Nathan Katz
Affiliation:
Worcester Polytechnic Institute, Worcester, MA. 01609
Gary L. Leatherman
Affiliation:
Worcester Polytechnic Institute, Worcester, MA. 01609
Harald Lucas
Affiliation:
Worcester Polytechnic Institute, Worcester, MA. 01609
Cornelia Demers
Affiliation:
Worcester Polytechnic Institute, Worcester, MA. 01609
Get access

Abstract

A novel approach in tensile testing of cementitious composites using the ASCERA® hydraulic tensile tester is described. The test specimens are cylindrical bars. Steel pistons are adhesively bonded on either end of the specimens and inserted in a pressure chamber. The pressure is increased until the specimen is pulled apart by the hydraulic pressure exerted on the pistons.

Advantages of this method are: large volume under load, self-alignment to minimize externally applied bending moments, and determination of the rupture stress exactly at the fracture initiation point.

Glass reinforced cementitious composites were tested. Results are discussed with respect to curing time and fiber volume fraction. The tensile strength values obtained by hydraulic testing are compared to values obtained by traditional uniaxial tensile strength tests. A biaxial model is adopted to verify the results.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 211: Symposium O – Fiber-Reinforced Cementitious Materials , 1990 , 221
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Hannant, D. J., The Structural Engineer, 50 (7), 253–258 (1972).Google Scholar
[2] Hughes, B. P., and Chapman, G. P., RILEM Bulletin, 26, 77–80 (1965).Google Scholar
[3] Elvery, R. H. and Haroun, W., Magazine of Concrete Research, 20 (63), 111–116 (1968).Google Scholar
[4] Ward, M. A. and Cook, D. J., Materials Research and Standards, MTRSA, 9 (5), 16–20 (1969).Google Scholar
[5] Johnston, C. D. and Sidwell, E. H., Magazine of Concrete Research, 20 (65), 221–228 (1968).CrossRefGoogle Scholar
[6] Baratta, F. I. and Driscoll, G. W., “A New Axial Tension Tester for Brittle Materials”, Army Materials and Mechanics Research Center, TR 69–02 (1969).Google Scholar
[7] Hermonsson, L., Adlerborn, J., and Burstrom, M. in High Tech Ceramics, Edited by Vincerzini, P., (Elsevier, Amsterdam, 1987) pp 1161–1168.Google Scholar
[8] Bennett, T. and Danzer, R., Br. Ceram. Trans. J., 89, 21–23 (1990).Google Scholar
[9] ASEA Cerama AB, “Instruction and Operation Manual for ASCERA Hydraulic Tensile Testing”, ASEA CERAMA AB, Robertsfors, Sweden, (1988).Google Scholar
[10] Driscoll, G. W. and Baratta, G. I.,“Modification to an Axial Tension Tester for Brittle Materials”, Army Materials and Mechanics Research Center, Watertown, Ma., AMMRC PTR 71–3 (1971).CrossRefGoogle Scholar
[11] Christ, B.W. and Swanson, S.R., Journal of Testing and Evaluation, 4 (6) pp. 405–417, (1976).Google Scholar