Hostname: page-component-76fb5796d-x4r87 Total loading time: 0 Render date: 2024-04-25T17:37:51.838Z Has data issue: false hasContentIssue false
  • English
  • Français

Surface Mechanical Properties of Ti Alloys Produced by Excimer Laser Mixing of Ti on AISI 304 Stainless Steel

Published online by Cambridge University Press:  25 February 2011

T. R. Jervis ,
J-P. Hirvonen ,
M. Nastasi ,
T. G. Zocco ,
J. A. Martin ,
G. M. Pharr  and
W. C. Oliver
T. R. Jervis
Affiliation:
Materials Science and Technology Division
J-P. Hirvonen
Affiliation:
Materials Science and Technology Division
M. Nastasi
Affiliation:
Materials Science and Technology Division
T. G. Zocco
Affiliation:
Materials Science and Technology Division
J. A. Martin
Affiliation:
Chemistry and Laser Sciences Division, Los Alamos National Laboratory, Los Alamos, NM 87545
G. M. Pharr
Affiliation:
Department of Materials Science, Rice University, Houston, TX 77251
W. C. Oliver
Affiliation:
Metals and Ceramics Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831
Get access

Abstract

We have investigated the properties of surface alloys of Ti formed by excimer laser melting and mixing of Ti overlayers on AISI 304 stainless steel substrates.The thickness of the initial Ti surface layers and the fluence and number of pulses used to mix the surface were varied to investigate a broad range of processing conditions. Samples were uniformly translated at different speeds under repetitive pulses of homogenized laser radiation at 308 nm to vary the number of pulses incident on the sample. We investigated the surface structure and composition, the wear and friction behavior, and the surface hardness of the resulting alloys.

The extent of mixing is observed by Rutherford backscattering spectroscopy to be proportional to the number of pulses incident on the sample. Amorphous surface layers are formed at some mixing levels with a composition which indicates that Ti substitutes for Fe in the stainless steel on a one to one basis. Incorporation of C from surface and interface contamination is observed but at a level much below that found in comparable ion implanted materials.

Friction coefficient measurements indicate that there exists an optimum level of mixing for each layer thickness. Excessive mixing degrades both the coefficient of friction and the wear performance in dry sliding tests.

As with the tribological measurements, the surface hardness showed a dependence on amount of mixing. The surface hardness of the as deposited samples was higher than that of the laser mixed samples, initially decreased with mixing, and finally increased with further mixing.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 128: Symposium A – Processing and Characterization of Materials Using Ion Beams , 1988 , 457
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Follstaedt, D. M., Knapp, J. A., Pope, L. E., Yost, F. G., and Picraux, S. T., Appl. Phys. Lett. 45 529 (1984).CrossRefGoogle Scholar
2. Hirvonen, J-P., Nastasi, M., and Mayer, J. W., Appl. Phys. Lett. 49 1345 (1986).CrossRefGoogle Scholar
3. Draper, C. W. and Mazzoldi, P., eds., Laser Surface Treatment of Metals (Martinus Nijhoff, Dordrecht, 1986).CrossRefGoogle Scholar
4. Hirvonen, J-P, Mayer, J. W., Nastasi, M., and Stone, D., Nucl. Instrum. B 23 487 (1987).CrossRefGoogle Scholar
5. Jervis, T. R., Nastasi, M., and Zocco, T. G. in Fundamentals of Beam Solid Interactions and Transient Thermal Processing, edited by Aziz, M. J., Rehn, L. E. and Stritzker, B. (Mater. Res. Soc. Proc. 100, Pittsburgh, PA 1988).Google Scholar
6. Jervis, T. R., Nastasi, M., Zocco, T. G., and Martin, J. A., Appl. Phys. Lett. 53 75 (1988).CrossRefGoogle Scholar
7. Knapp, J. A., Follstaedt, D. M., and Doyle, B. L., Nucl. Instrum. Methods. B 7 38 (1985).CrossRefGoogle Scholar
8. Jervis, T. R., Hirvonen, J-P., and Nastasi, M., In Press, J. Mater. Res. Nov-Dec (1988).Google Scholar
9. Oliver, W. C., Hutchings, R., and Pethica, J. B., ASTM Spec. Tech. Pub. 889, 90 (1986).Google Scholar
10. Doemer, M. F. and Nix, W. D., J. Mater. Res. 1 601 (1986).Google Scholar
11. Fayeulle, S. and Singer, I. L. (personal communication).Google Scholar
12. Jervis, T. R., Frydrych, D. J., and Baer, D. R., Mater. Lett. 6 225 (1988).CrossRefGoogle Scholar
13. Baer, D. R., Frydrych, D. J., and Jervis, T. R., in Environmental Degredation of Ion and Laser Beam Treated Surfaces, edited by Was, G. S. and Grabowski, K. (The Metallurgical Society, Warrendale, PA 1989).Google Scholar