Hostname: page-component-848d4c4894-x5gtn Total loading time: 0 Render date: 2024-04-30T21:17:20.829Z Has data issue: false hasContentIssue false
  • English
  • Français

Superplastic Deformation Mechanisms in a Fine-Grained, Yttria-stabilized Tetragonal Zirconia Polycrystal (Y-TZP)

Published online by Cambridge University Press:  16 February 2011

T. G. Nieh  and
J. Wadsworth
T. G. Nieh
Affiliation:
Lockheed Missiles and Space Company, Research and Development Division, O/9310, B/204, 3251 Hanover Street, Palo Alto, CA 94304
J. Wadsworth
Affiliation:
Lockheed Missiles and Space Company, Research and Development Division, O/9310, B/204, 3251 Hanover Street, Palo Alto, CA 94304
Get access

Abstract

Concurrent grain growth, and in particular, dynamic grain growth, was observed to take place during superplastic deformation of Y-TZP. As a result of this concurrent grain growth, the measured strain rate sensitivity was found to be lower than that measured under constantstructure conditions. In the present paper, data obtained from the superplastic deformation of YTZP under constant-structure conditions are presented. It is demonstrated that the strain rate sensitivity values are generally higher than 0.5, when measured from the grain size-compensated data; this result suggests a grain boundary sliding mechanism. Microstructures from samples prior to and after superplastic deformation reveal grains which are essentially equiaxed; this observation is also consistent with a grain boundary sliding mechanism. Both high-resolution images of grain boundary triple points using transmission electron microscopy, and fracture surface studies using Auger electron spectroscopy and X-ray photoelectron spectroscopy indicate that there is no evidence for the presence of glassy phases at grain boundaries in Y-TZP.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 196: Symposium T – Superplasticity in Metals, Ceramics, and Intermetallics , 1990 , 331
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Wakai, F., Sakaguchi, S., and Matsuno, Y., Adv. Ceram. Mater., 1, 259–263 (1986).Google Scholar
2. Wakai, F. and Kato, H., Adv. Ceram. Mater., 3, 71–76 (1988).Google Scholar
3. Nieh, T.G., McNally, C.M., and Wadsworth, J., Scripta Metall., 22, 1297–1300 (1988).Google Scholar
4. Nieh, T.G., McNally, C.M., and Wadsworth, J., Scripta Metall., 23, 457–460 (1989).Google Scholar
5. Wang, J.-G. and Raj, R., J. Amer. Ceram. Soc., 67 [6], 385–390 (1984).Google Scholar
6. Wang, J.-G. and Raj, R., J. Amer. Ceram. Soc., 67 [6], 399–409 (1984).Google Scholar
7. Wakai, F., Kodama, Y., and Sakaguchi, S., and Nonami, T., J. Amer. Ceram. Soc., 73 [2], 457–460 (1990).Google Scholar
8. Wakai, F., Okamura, H., Kimura, N., and Descamps, P.G.E., Proc. 1st. Japan Inter. SAMPE Symposium, (1989) pp. 267–275.Google Scholar
9. Carry, C., in MRS Intl. Meeting on Advanced Materials Vol 7 (IMAM-7. Superplasticity), edited by Kobayashi, M. and Wakai, F., (Materials Res. Soc., Pittsburgh, PA 1989) pp. 199–216.Google Scholar
10. Langdon, T.G., “Superplastic Ceramics - an Overview”, Presented at the 119th TMS Annual Meeting, Anaheim, California, February, 19, 1990.Google Scholar
11. Pharr, G.M. and Ashby, M., Acta Metall., 31, 129–138 (1983).Google Scholar
12. Nieh, T.G., Wadsworth, J., and Sherby, O.D., in MRS Intl. Meeting on Advanced Materials Vol 7 (IMAM-7. Superplasticity, edited by Kabayashi, M. and Wakai, F., (Materials Res. Soc., Pittsburgh, PA 1989) pp. 251–258.Google Scholar
13. Nieh, T.G. and Wadsworth, J., J. Amer. Ceram. Soc. Comm., 72 [8], 1469–1472 (1989).Google Scholar
14. Wakai, F., Sakaguchi, S., and Kato, H., J. Ceram. Soc. Jap., 94, 72–75 (1986). (In Japanese)Google Scholar
15. Okamoto, Y., Ieuji, J., Yamada, Y., Hayashi, K., and Nishikawa, T., in Advances in Ceramics. Vol 24, edited by Somiya, S., Yamamoto, N., and Yanagida, H., (American Ceramic Society, Inc., Westerville, OH 1988) pp. 565–571.Google Scholar
16. Hermanson, T., Lagerlof, K.P.D., and Dunlop, G.L., in Superplasticity and Superplastic Forming, edited by Hamilton, C.H. and Paton, N.E., (TMS, Warrendale, PA 1988) pp. 631–635.Google Scholar
17. Duclos, R., Crampon, J., and Amana, B., Acta Metall., 32, 877–883 (1987).Google Scholar
18. Seltzer, M.S. and Talty, P.K., J. Amer. Ceram. Soc., 58 [3–4], 124–130 (1975).Google Scholar
19. Mills, M.J., Gibeling, J.C., and Nix, W.D., Acta Metall., 32, 1503–1514 (1985).Google Scholar
20. Rai, G. and Grant, N.J., Metall. Trans., 6A, 385–390 (1975).Google Scholar
21. Mishra, R.S. and Murty, G.S., J. Mater. Sci. Lett., 7, 185–186 (1988).Google Scholar
22. Nieh, T.G. and Wadsworth, J., Scripta Metall., (1990). In Press.Google Scholar
23. Sherby, O.D. and Burke, P.M., Prog. Mater. Sci., 13, 325–390 (1967).Google Scholar
24. Clarke, D.R. and Thomas, G., J. Am. Ceram. Soc., 60 [11–12], 491–495 (1977).Google Scholar
25. Nieh, T.G., Yaney, D.L., and Wadsworth, J., Scripta Metall., 23 [12] 2007–2012 (1989).Google Scholar