Hostname: page-component-77c89778f8-gvh9x Total loading time: 0 Render date: 2024-07-20T23:08:34.035Z Has data issue: false hasContentIssue false

Palladium Supported on Alumina Catalysts Prepared by MOCVD and Impregnation Methods

Published online by Cambridge University Press:  15 February 2011

G. Garcia
Affiliation:
Dept. of Chemical Engineering, ESIQIE-IPN, México 07738 D.F., MEXICO
J.R. Vargas
Affiliation:
Dept. of Metallurgical Engineering, ESIQIE-IPN, AP 75-874, México 07300, D.F., MEXICO
M.A. Valenzuela
Affiliation:
Dept. of Chemical Engineering, ESIQIE-IPN, México 07738 D.F., MEXICO
M. Rebollar
Affiliation:
Dept. of Chemical Engineering, ESIQIE-IPN, México 07738 D.F., MEXICO
D. Acosta
Affiliation:
Institute of Physics, UNAM., AP 20-364, México 01000 D.F., MEXICO
Get access

Abstract

Conventional MOCVD method has been explored to prepare Pd supported catalysts. Pd and PdO phases were found on the surface of the support. Small Pd particles about 1 to 3 nm and dispersions up to 19%were obtained by MOCVD. TPR results indicated that several surface Pd compounds are reduced. At temperatures below 25°C, PdO, the main compound, is completely converted to metallic Pd which forms hydrides. At higher temperatures, between 500 to 800°C, the reduction peaks could be attributed to Pd-support interactions and a strong support dehydroxylation. All catalysts were inactive in benzene hydrogenation and a significant conversion was only detected a temperatures above 100 °C. This was explained by the reduced accessibility of Pd sites imposed by the carbon contamination and by the Pd-Al2O3 interactions.

Type
Research Article
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Garbowski, E., Feumi-Jantou, C., Mouaddib, N. and Primet, M.. Appl. Catal. A General 109, 277291 (1994).Google Scholar
2. Che, M. and Bennett, C.O., Adv.Catal. 36, 55 (1989).Google Scholar
3. López, T., Bosch, P., Morán, M., Gómez, R., J.Phys.Chem., 97, 1671 (1993).Google Scholar
4. Goto, T., Vargas, R., and Hirai, T.. Mat. Sci. Eng. A 217/218, 223226 (1996).Google Scholar
5. Shengchun, Y., Hideaki, M., Kusakabe, K. and Moruuka, S.. Ind. Eng. Chem. Res. 33, 616622 (1994).Google Scholar
6. Dossi, C., Psaro, R., Bartsch, A., Brivio, E., Galasco, A. and Losi, P.. Catal. Today. 17, 327535 (1993).Google Scholar
7. Dossi, C., Bartsch, A., Fusi, A., Sordelli, L., Ugo, R., Bellatrecia, M., Zanoni, R. and Vlaic, G.. J. Catal. 145, 377 (1994).Google Scholar
8. Feurer, R., Reynes, A., Serp, P., Kalck, P. and Morancho, R.. Colloque C5, Suppl. Au J. Phys. II, 5 C5(1037-1042).Google Scholar
9. Serp, P., Feurer, R., Morancho, R. and Kalck, P.. J. Catal. 157, 294300 (1995).Google Scholar
10. Zhang, R., Schwarz, J. A., Datye, A. and Baltrus, J. P.. J. Catal. 138, 5569 (1992).Google Scholar
11. Lopez, Z.K., Vargas, J.R., Valenzuela, M.A., Acosta, D.R. in Advanced Catalytic Materials 1997, edited by Rodriguez, Nelly M., Soled, Stuart L. and, Hrbek, Jan (Mat. Res. Soc. Symp. Proc. 497, Pittsburgh, PA, 1997) pp. 8792.Google Scholar