Hostname: page-component-7479d7b7d-wxhwt Total loading time: 0 Render date: 2024-07-11T07:36:35.504Z Has data issue: false hasContentIssue false

Mechanical and Microstructural Properties of Two-Step Acid-Base Catalyzed Silica Gels

Published online by Cambridge University Press:  21 February 2011

D. E. Meyers
Affiliation:
YTC America Inc., 550 Via Alondra, Camarillo, CA 93012.
F. Kirkbir
Affiliation:
YTC America Inc., 550 Via Alondra, Camarillo, CA 93012.
H. Murata
Affiliation:
YTC America Inc., 550 Via Alondra, Camarillo, CA 93012.
S. Ray chaudhuri
Affiliation:
YTC America Inc., 550 Via Alondra, Camarillo, CA 93012.
A. Sarkar
Affiliation:
YTC America Inc., 550 Via Alondra, Camarillo, CA 93012.
Get access

Abstract

The mechanical and microstructural properties of two-step acid-base catalyzed silica gels were examined as functions of aging time, catalyst concentration, and hydrolysis time. Cylindrical gels were prepared using Si(OC2H5)4, C2H5OH, and H2O, with HCl followed by NH3 as catalysts. Mechanical properties were obtained from three-point bend tests, and the microstructures of dried gels were analyzed using nitrogen adsorption/desorption techniques. Gel strength initially increased with aging time at 70 °C, then leveled off after about one week. When the sol was hydrolyzed for less than two hours, there were significant differences in the properties of gels catalyzed with relative molar amounts of 0.0001 and 0.0002 HCl. However, as the hydrolysis time was increased, the gels all had similar properties, independent of the amount of HC1. The amount of NH3 influenced gelation time and to a lesser extent, the strength, but had no observable effect on pore size. The two-step catalysis procedure produced gels with strength and pore size combinations intermediate to those of either single acid or base-catalyzed gels.

Type
Research Article
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1 Scherer, G. W., J. Non-Cryst. Solids 109, 183 (1989).Google Scholar
2 Kirkbir, F., Murata, H., Meyers, D. E., Chaudhuri, S. Ray, and Sarkar, A., presented at the 1993 Am. Cer. Soc. PAC RIM meeting, Honolulu, HI, 1993 (to be published).Google Scholar
3 Dumas, J., Baza, S., and Serughetti, J., J. Mater. Sci. Let. 5, 478 (1986).Google Scholar
4 West, J. K., Nikles, R., and Lattore, G. in Better Ceramics Through Chemistry III, edited by Brinker, C. J., Clark, D. E., and Ulrich, D. R. (Mater. Res. Soc. Proc. 121, Pittsburgh, PA, 1988) pp.219- 225.Google Scholar
5 Haereid, S., Einarsrud, M. A., and Scherer, G. W., submitted to J. Sol-Gel Sci. Tech., 1993.Google Scholar
6 Meyers, D. E., Murata, H., Kirkbir, F., Chaudhuri, S. Ray, and Sarkar, A., to be presented at the 1994 Am. Cer. Soc. Annual Meeting, Indianapolis, IN, 1994.Google Scholar
7 Brinker, C. J., Keefer, K. D., Schaefer, D. W., Assink, R. A., Kay, B. D., and Ashley, C. S., J. Non-Cryst. Solids 63, 45 (1984).Google Scholar
8 Boonstra, A. H. and Mulder, C. A. M., J. Non-Cryst. Solids 105, 201 (1988).Google Scholar
9 Boonstra, A. H. and Bernards, T. N. M., J. Non-Cryst. Solids 105, 207 (1988).Google Scholar
10 ASTMC674-88(1988).Google Scholar
11. Autosorb-6 Sorption System Manual, Quantachrome Corp., Syosset, NY (1989), pp 11-13.Google Scholar
12 Scherer, G. W., Pardenek, S. A., and Swiatek, R. M., J. Non-Cryst. Solids 107, 14 (1988).Google Scholar
13 Brinker, C. J. and Scherer, G. W., Sol-Gel Science. (Academic Press, New York, 1990).Google Scholar
14 Einarsrud, M. A. and Haereid, S., presented at the 7th Intl. Workshop, on Glasses and Ceramics From Gels, J. Sol-Gel Sci. Tech., Paris, 1993 (to be published).Google Scholar
15 Woignier, T., Phalippou, J., Hdach, H., Larnac, G., Pernot, F., and Scherer, G. W., J. Non-Cryst. Solids 147 & 148, 672 (1992).Google Scholar