Hostname: page-component-848d4c4894-4rdrl Total loading time: 0 Render date: 2024-06-28T18:48:39.634Z Has data issue: false hasContentIssue false
  • English
  • Français

Manufacturing of Hybrid Composites and Novel Methods to Synthesize Carbon Nanoparticles

Published online by Cambridge University Press:  01 February 2011

Andres E. Fals ,
Julio Quintero  and
F. C. Robles Hernández
F. C. Robles Hernández
Affiliation:
University of Houston, Department of Mechanical Engineering Technology, College of Technology, 304 Technology Building, Houston, TX 77204–4020.
Get access

Abstract

In following are presented the characterization results of nanostructured hybrid composites using alumina matrix reinforced with nanostructured particles of Ni, Ti and soot. The soot used in this work is the byproduct from the synthesis of Carbon Nanotubes (CNT) or fullerene and contains traces (>1wt%) of either CNT or fullerene. Ni and Ti are used in this work for their inherent catalytic ability for heterogeneous nucleation of carbon nanostructures (nanotubes, fullerenes). The hybrid composites are produced by a combination of methods including mechanical milling, sonication, and Spark Plasma Sintering (SPS). Mechanical milling is conducted in high energy mills, the milled and as manufactured powders are sonicated to assure their dispersion, homogeneity and promote percolation of the components during sintering. Mechanical milling and SPS have positive effects to promote the synthesis of different carbon nanoparticles. For instance, it is observed that mechanical milling of fullerene soot sponsors the synthesis of nanostructured diamond particles and using SPS can be synthesized diamond too and fullerene. Although, it is important to notice that SPS conditions are critical to the amount and type of synthesized particles. The use of CNT soot sponsors porosity, hence lower density resulting in an ideal material for membrane and porous media applications. The results of characterization (X-Ray diffraction, electron microscopy (scanning and transmission)) and the mechanical properties (Vickers microhardness) are discussed accordingly.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1276: Advanced Structural Materials–2010 , 2010 , 3
Copyright
Copyright © Materials Research Society 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Harris, P. J. F., Carbon nanotubes and related structures, Cambridge University Press, Cambridge 1999.Google Scholar
2. Kroto, H. W., Heath, J. R., O’Brien, S. C., Curl, R. F., Smalley, R. E., C60: Buckminsterfullerene, Nature, 318, 162–163 (1985).Google Scholar
3. Iijima, S., Helical microtubules of graphitic carbon, Nature, 354, 56–58 (1991).Google Scholar
4. Ru, Q., Kamoto, M., Kondo, Y., Takayanagi, K., Attraction and orientation phenomena of bucky onions formed in a transmission electron microscope, Chem Phys Lett 259, 425–431 (1996).Google Scholar
5. Ugarte, D., Curling and closure of graphitic networks under electron-beam irradiation, Nature, 359 (1992) 707–709.Google Scholar
6. Terrones, H., Terrones, M., The transformation of polyhedral particles into graphitic onions, J Phys Chem Solids, 58 1789–1796 (1997).Google Scholar
7. Treacy, M. M., Ebbesen, T. W., Gibson, J. M., Exceptionally high Young's modulus observed for individual carbon nanotubes, Nature, 381, 678 (1996).Google Scholar
8. Lourie, O., Cox, D. M., Wagner, H. D., Buckling and Collapse of Embedded Carbon Nanotubes, Phys Rev Lett., 81, 1638–1641 (1998).Google Scholar
9. Umemoto, M., Masuyama, K., Raviprasad, K., Mechanical Alloying of Fullerene with Metal, Mats. Sci. Forum 47, 235–238 (1997).Google Scholar
10. Robles Hernandez, F. C., Production and Characterization of Composites Metal-C (where Metal= Fe or Al and C= Graphite or Fullerene) Obtained from Mechanically Alloyed Powders, MSc Thesis, Instituto Politécnico Nacionál, Departamento de Ingeniería Metalúrgica, Mexico, 1999.Google Scholar
11. Robles Hernández, F. C., Calderón, H. A., “Nanostructured Metal Composites Reinforced with Fullerenes”, JOM, 62, 2, 2010, 63–68.Google Scholar
12. Robles Hernández, F. C., Calderón, H. A., “Synthesis of fullerene on Fe-C composites by Spark Plasma Sintering and its thermomechanical transformation to diamond”, MRS Proceedings, 1243, 2010.Google Scholar
13. Sun, L., Banhart, F., Krasheninnikov, A. V., Rodrguez-Manzo, J. A., Terrones, M., Ajayan, P. M., Carbon Nanotubes as High-Pressure Cylinders and Nanoextruders, Science, 312 1199–1202 (2006).Google Scholar
14. Garibay-Febles, V., Calderon, H. A., Robles-Hernández, F. C., Umemoto, M., Masuyama, K., Cabañas-Moreno, J. G., Production and Characterization of (Al, Fe)-C (Graphite or Fullerene) Composites Prepared by Mechanical Alloying, Mats & Manufac Processes, 15, 547–567 (2000).Google Scholar
15. Zhan, G-D., Kuntz, J., Wan, J., Garay, J., Mukherjee, A. K., “A Novel Processing Route to Develop a Dense Nanocrystalline Alumina Matrix (<100 nm) Nanocomposite Material, J. Am. Ceram. Soc., 86, 200–202 (2002).Google Scholar
16. Zhan, G-D., Kuntz, J., Wan, J., Garay, J., Mukherjee, A. K., Alumina-based nanocomposites consolidated by spark plasma sintering, Scripta Materialia 47, 737–741 (2002).Google Scholar
17. Zapata-Solvas, E., Gomez-Garcia, D., Poyato, R., Lee, Z., Castillo-Rodriguez, M., Dominguez-Rodriguez, A., Radmilovic, V., Padture, N. P., Microstructural Effects on the Creep Deformation of Alumina/Single-Wall Carbon Nanotubes Composites, J. Am. Ceram. Soc., 93, 7, 2042–2047 (2010)Google Scholar
18. Zhan, G-D., Kuntz, J. D., Garay, J. E., Mukherjee, A. K., Electrical properties of nanoceramics reinforced with ropes of single-walled carbon nanotubes, 83, 6, 1228–1230 (2003).Google Scholar
19. Gilman, P.S. and Benjamin, J.S., Ann. Rev. Mater. Sci. 13, 279 (1983).Google Scholar
20. Suryanarayana, C., Prog. Mater Sci. 46, 1, (2001).Google Scholar
21. Ownby, P. D., Yang, X., Liu, J., Calculated X-ray Diffraction Data for Diamond Polytypes, J Am. Ceram. SOC., 75, 7 (1992) 1876–83.Google Scholar
22. Santana-García, I., Hernandez-Robles, F.C., Garibay-Febles, V., H. A. Calderon Metal (Fe, Al)-Fullerene Nanocomposites: Synthesis and Characterization, Microscopy and Microanalysis, 16, S2 (2010) 1688–1689.Google Scholar
23. Xia, Z., Riester, L., Sheldon, B. W., Curtin, W. A., Liang, J., Yin, A., Xu, J. M., Mechanical properties of highly ordered nanoporous anodic alumina membranes, Rev. Adv. Mat. Sci. 6, 2004, 131–139.Google Scholar
24. Krell, A., Blank, P., Grain size dependence of hardness in dense sub micrometric alumina, J. Am. Ceram. Soc., 78, 4, (1195) 1118–1120.Google Scholar