Skip to main content Accessibility help

Laminate MEMS for Heterogeneous Integrated Systems

  • G. P. Li (a1) and Mark Bachman (a1)


Post semiconductor manufacturing processes (PSM), including packaging and printed circuit board (PCB) manufacturing are now capable of producing trace widths of a few micrometers, high aspect ratio vias, three-dimensional constructions, and highly integrated systems in a single small package. Such PSM technology can in principle be used to manufacture micro electromechanical systems (MEMS) for sensing and actuation applications. Although MEMS are traditionally produced using silicon processes, the broad array of manufacturing approaches available in the packaging industry, including lamination, lithography, etching, electroforming, machining, bonding, etc., and the large number of available materials such as polymers, ceramics, metals, etc., provides greater design freedom for producing functional microdevices. The results of such processes applied to fabricating small systems are heterogeneously integrated MEMS devices. Since lamination of stacked layers is a critical component of this process, we refer to these devices as “laminate MEMS.”

In many cases laminate MEMS devices are more suited to their applications than their silicon counterparts, especially for applications such as biomedical, optical, and human computer interface. Furthermore, such microdevices can be built with a high degree of integration, pre-packaged, and at low cost. Indeed, the PCB and packaging industries stand to benefit greatly by expanding their offerings beyond serving the semiconductor industry and developing their own devices and products. This paper illustrates that good quality MEMS devices can be manufactured using packaging style fabrication, particularly using stacks of laminates, and discusses some of the unique benefits of such devices. This laminate MEMS technology promises not only improved methods for manufacturing microdevices but also for heterogeneously integrating them with silicon microelectronics and other components into a single package.



Hide All
1. Kada, Morihiro, “The Dawn of 3D Packaging as System-in-Package (SIP)”, IEICE TRANSACTIONS on Electronics Vol.E84-C No.12, pp.17631770 (2001).
2. Peterson, K., “Silicon as a mechanical materialProceedings of the IEEE. Vol 70, No. 5, pp. 420457 (1982).
3. Maluf, Nadim and Williams, Kirt. Introduction to microelectromechanical systems engineering. Artech House, Boston, MA (2004).
4. Chiou, J.A., Lee, Y.C., Kurabayashi, K., Candler, R., “Foreword Special Section on Packaging for Micro/Nano-Scale Systems.” Advanced Packaging, IEEE Transactions on. Vol. 32 No.2, pp.399401 (2009).
5. Ulrich, Richard K. and Brown, William D. (Eds). Advanced Electronic Packaging (IEEE Press Series on Microelectronic Systems). Wiley-IEEE Press, Hoboken, New Jersey. (2006)
6. Madou, Marc, Fundamentals of Microfabrication and Nanotechnology, Third Edition, Three-Volume Set: From MEMS to Bio-MEMS and Bio-NEMS: Manufacturing Techniques and Applications, CRC Press-Taylor & Francis, Boca Raton, FL (2011).
7. Chang, HP, Qian, J., Cetiner, B.A., De Flaviis, F., Bachman, M., Li, GP. “Design and process considerations for fabricating RF MEMS switches on printed circuit boards,” Journal of Microelectromechanical Systems, 14 (6), pp. 13111322 (2005).
8. Palasagaram, JN, Ramadoss, R. “MEMS-Capacitive Pressure Sensor Fabricated Using Printed-Circuit-Processing Techniques”, IEEE Sensors, Vol. 6 No 6, pp. 13741375 (2006).
9. Ramadoss, R., Lee, S., Lee, Y. C., Bright, V. M. and Gupta, K. C.. “Fabrication, assembly, and testing of RF MEMS capacitive switches using flexible printed circuit technology”, IEEE Trans. Adv. Packag., vol. 26, pp. 248 (2003)
10. Wang, X., Lu, L.-H. and Liu, C.. “Liquid crystal polymer (LCP) for MEMS: Processes and applications”, J. Micromech. Microeng., vol. 13, pp. 628 (2003).
11. Ghodsian, B., Changwon, J., Cetiner, B.A., De Flaviis, F., “Development of RF-MEMS switch on PCB substrates with polyimide planarization”. IEEE Sensors, Vol 5, pp. 950955 (2005).
12. Chang, C. H., Qian, J. Y., Cetiner, B. A., Xu, Q., Bachman, M., De Flaviis, F., and Li, G. P., “RF MEMS capacitive switches fabricated with HDICP CVD SiNx”, IEEE MTT-S Int. Microwave Symp., pp. 231234 (2002).
13. Bachman, M and Li, GP, “Methods of Manufacturing Microdevices in Laminates, Lead Frames, Packaging,” US Patent Application 12/112,925, USPTO Publication US 2008/0283180 A1, April 30, 2008.
14. Chang, H.P., Qian, J.Y., Cetiner, B.A., De Flaviis, F., Bachman, M., and Li, G.P., “Low cost RF MEMS switches fabricated on microwave laminate printed circuit board”, IEEE Electron Device Letters, Vol. 24, No. 4, pp. 227229, 2003.
15. Cetiner, B. A., Chang, H. P., Qian, J.Y., Bachman, M., Li, G.-P., and De Flaviis, F., “RF MEMS switches fabricated on low cost microwave laminates using low temperature processes,” IEEE Trans. on Microwave Theory and Tech., Vol. 51, pp. 332335, Jan. 2003.
16. Bachman, M, Zhang, Yang, Wang, Minfeng, and Li, GP, “High Power Direct Contact (DC) Magnetically Actuated Microswitches Fabricated in Laminates,” submitted to IEEE Electron Device Letters.
17. Xu, Tao, Bachman, Mark, Zeng, Fan-Gang, and Li, G. P., “Polymeric Micro-cantilever Array for Auditory Front-end Processing,” Sensors and Actuators A: Physical, Vol. 114, pp. 176182, Sep. 2004.
18. Liu, Hung-Wei, Chang, Ho-Jung, Li, Guann-Pyng, Bachman, Mark, “Performance Improvement of Organic Thin-Film Transistors by Solution-Processed Crystallization of Pentacene at Room Temperature”, IEEE Electron Device Letters, Vol. 30, No. 4, 346348, 2009


Laminate MEMS for Heterogeneous Integrated Systems

  • G. P. Li (a1) and Mark Bachman (a1)


Full text views

Total number of HTML views: 0
Total number of PDF views: 0 *
Loading metrics...

Abstract views

Total abstract views: 0 *
Loading metrics...

* Views captured on Cambridge Core between <date>. This data will be updated every 24 hours.

Usage data cannot currently be displayed