Hostname: page-component-68945f75b7-zpsnj Total loading time: 0 Render date: 2024-08-05T15:31:53.239Z Has data issue: false hasContentIssue false
  • English
  • Français

Interfacial Shear Behavior of Sapphire-Reinforced NiAi Composites

Published online by Cambridge University Press:  21 February 2011

C. A. Moose ,
D. A. Koss  and
J. R. Hellmann
C. A. Moose
Affiliation:
Center for Advanced Materials The Pennsylvania State University University Park, PA 16802
D. A. Koss
Affiliation:
Center for Advanced Materials The Pennsylvania State University University Park, PA 16802
J. R. Hellmann
Affiliation:
Center for Advanced Materials The Pennsylvania State University University Park, PA 16802
Get access

Abstract

The interfacial shear behavior in near-equiatomic NiA1 reinforced by sapphire filaments has been examined at room temperature using a fiber pushout test technique. The loaddisplacement data indicate a large variability in the initial interface failure stress, although reverse push behavior indicates a comparatively constant interfacial sliding friction stress. The observed behavior suggests that the presence of asperities on the fiber surfaces and nonuniformities in fiber diameter require constrained plastic flow within the NiAl matrix in order for interfacial shear to occur. The location, shape, severity, and distribution of fiber asperities as well as the uniformity of fiber diameter are critical to the interfacial shear process.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 194: Symposium R – Intermetallic Matrix Composites I , 1990 , 293
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Noebe, R.D., Bowman, R.R., and Eldridge, J.I., this Proceedings.Google Scholar
2. Petrasek, D.W., in HITEMP Review 1989. Advanced High Temperature Engine Materials Technology Prog-am, Proceedings of the 2nd Annual HITEMP Review, Cleveland, OH, NASA CP 10039, 1989, p. 8–1.Google Scholar
3. Pascoe, R.T. and Newey, C.W.A., Met. Sci. J. 2, 138 (1968).Google Scholar
4. Ball, A. and Smallman, R., Acta Met. 14, 1349 (1966).Google Scholar
5. Vedula, K., Hahn, K.H., and Boulogne, B. in High Temperature Ordered Intermetallic Alloys III, edited by Liu, C.T., Taub, A.I., Stoloff, N.S., and Koch, C.C., (Mater. Res. Soc. Proc. 113 Pittsburgh, PA 1989), p. 299.Google Scholar
6. Saphikon, Inc., Milford, NH 03055; product specification sheet 040188.Google Scholar
7. Sayir, A., Hurst, J.B., and Jones, S., in HITEMP Review 1989. Advanced High Temperature Engine Materials Technology Program, Proceedings of the 2nd Annual HITEMP Review, Cleveland, OH, NASA CP 10039, 1989, p. 72–1.Google Scholar
8. Bright, J.B., Shetty, D.K., Griffin, C.W., and Limaye, S.Y., J. Am. Cer. Soc. 72, 1891 (1989).Google Scholar
9. Introduction to Ceramics, 2nd Edition, edited by Kingery, W.D., Bowen, H.K., and Uhlmann, D.R. (John Wiley & Sons, New York, 1976), p. 595.Google Scholar
10. Stephens, J.R., in High Temperature Ordered Intermetallic Alloys, edited by Koch, C.C., Liu, C.T., and Stoloff, N.S. (Mater. Res. Soc. Proc. 32, Pittsburgh, PA 1985) pp.381–395 Google Scholar