Hostname: page-component-5c6d5d7d68-sv6ng Total loading time: 0 Render date: 2024-08-14T16:18:42.970Z Has data issue: false hasContentIssue false
  • English
  • Français

High Dynamic Mechanical Strength of Zirconium-Based Bulk Amorphous Alloys

Published online by Cambridge University Press:  10 February 2011

Tao Zhang  and
Akihisa Inoue
Tao Zhang
Affiliation:
Institute for Materials Research, Tohoku University, Sendal 980–8577, Japan
Akihisa Inoue
Affiliation:
Institute for Materials Research, Tohoku University, Sendal 980–8577, Japan
Get access

Abstract

A bulk amorphous Zr55Al10Ni5Cu30 alloy prepared by squeeze casting was found to exhibit high mechanical strength values, i.e., uniaxial tensile fracture strength (σt) of 1850 MPa, three-point bending strength (σb) of 3200 MPa, bending fatigue strength (σf) of 1100 MPa, Charpy impact fracture energy (Ef) of 135 kJ/m2 and fracture toughness of 68 MPa√m. The σb, σf and Ef are about two times higher than those for the corresponding bulk amorphous alloys prepared by unidirectional solidification and powder consolidation techniques, though the σt of the squeeze cast sample is higher by about 15 % than those for the other samples. The remarkable increases in the σb, σf and EF are presumably due to the introduction of high compressive residual stress of about 1240 MPa in the outer surface region only for the squeeze cast sample. The finding of the effectiveness of the compressive residual stress on the increase in the mechanical strength under the bending stress mode is important and expected to be widely used as a new strengthening mechanism for bulk amorphous alloys, as is the case for reinforced oxide glasses subjected to strengthening treatment.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 554: Symposium MM – Bulk Metallic Glasses , 1998 , 361
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

(1) Inoue, A., Mater. Trans., JIM 36(1995), 866.Google Scholar
(2) Inoue, A., Sci. Rep. Res. Inst. Tohoku Univ., A42(1996), 1.Google Scholar
(3) Kui, H.W., Greer, A-L. and Turnbull, D., Appl. Phys. Let, 45(1984), 615.Google Scholar
(4) Kui, H.W. and Turnbull, D., Appl. Phys. Left, 47(1985), 796.Google Scholar
(5) Willnecker, R., Wittmann, K. and Gorler, G.P., J. Non-Cryst Solids, 156–158(1993), 450.Google Scholar
(6) Maitrepierre, P.L., J. Appl. Phys., 40(1969), 4826.Google Scholar
(7) Inoue, A., Ohtera, K., Kita, K. and Masumoto, T., Jpn. J. Appl. Phys., 27(1988), L2248.Google Scholar
(8) Inoue, A., Zhang, T. and Masumoto, T., Mater. Trans., JIM, 30(1989), 965.Google Scholar
(9) Inoue, A., Zhang, T. and Masumoto, T., Mater. Trans., JIM, 31(1990), 177.Google Scholar
(10) Peker, A. and Johnsosn, W.L., Appl. Phys. Lett., 63(1993), 2342.Google Scholar
(11) Inoue, A., Shibata, T. and Zhang, T., Mater. Trans., JIM, 36(1995), 1420.Google Scholar
(12) Inoue, A. and Gook, J.S., Mater. Trans., JIM, 36(1995), 1180.Google Scholar
(13) Inoue, A., Nishiyama, N. and Matsuda, T., Mater. Trans., JIM, 37(1996), 181.Google Scholar
(14) He, Y. and Schwarz, R.B., Metall. Mater. Trans., in press.Google Scholar
(15) Inoue, A., Zhang, T., Takeuchi, A. and Itoi, T., Mater. Trans., JIM, 38(1997), 359.Google Scholar
(16) Zhang, T. and Inoue, A., Mater. Trans., JIM, 39(1998), in press.Google Scholar
(17) Dunlop Catalogue, Japan Dunlop, Tokyo, (1998).Google Scholar
(18) Hiranuma Industrial Co., Ltd., Mito, private communication (1998).Google Scholar
(19) Inoue, A., Yokoyama, Y., Shinohara, Y. and Masumoto, T., Mater. Trans., JIM, 35(1994), 923.Google Scholar
(20) Kato, A., Kawamura, Y. and Inoue, A., Mater. Trans., JIM, 37(1996), 70.Google Scholar
(21) Inoue, A., Mater. Sci. Forum, 269–272(1998), 855.Google Scholar
(22) Inoue, T., Glass Handbook, ed. by Sakka, , Takahashi, and Sakaino, , Asakurashotten, Tokyo, (1975), p.485.Google Scholar
(23) Askeland, D.R., Science and Engineering Materials, PWS Publishing, Boston (1994), p. 144.Google Scholar
(24) Gilbert, C. J., Lippmann, J. M. and Ritchie, R.O., Scripta Mater., 38(1998), 537.Google Scholar
(25) Askeland, D.R., Science and Engineering Materials, PWS Publishing, Boston, (1994), p.154.Google Scholar
(26) Gilbert, C. J. Ritchie, R. O. and Johnson, W. L., Appl. Phys. Lett., 71(1997), 473.Google Scholar
(27) Kimura, H.M., Inoue, A., Nishiyama, N., Sasamori, K, Haruyama, O. and Masumoto, T., Sci. Rep. Res. Inst. Tohoku Univ., A43(1997), 101.Google Scholar
(28) Materials Science of Amorphous Metals, Ohmu, Tokyo, (1982), p.202.Google Scholar
(29) Inoue, A., Zhang, T. and Masumoto, T., J. Non-Cryst. Solids, 156–158(1993), 473.Google Scholar