Hostname: page-component-5c6d5d7d68-vt8vv Total loading time: 0.001 Render date: 2024-08-20T17:48:26.508Z Has data issue: false hasContentIssue false
  • English
  • Français

Evaluation of Dry Etching Induced Damage of Gainas Using Transmission Lines and Schottky Diodes

Published online by Cambridge University Press:  22 February 2011

S. Thomas III  and
S. W. Pang
S. Thomas III
Affiliation:
The University of Michigan, Department of Electrical Engineering and Computer Science, Ann Arbor, MI 48109-2122
S. W. Pang
Affiliation:
The University of Michigan, Department of Electrical Engineering and Computer Science, Ann Arbor, MI 48109-2122
Get access

Abstract

Plasma etching of GaInAs and AlInAs has been carried out in a system which consists of an electron cyclotron resonance (ECR) source and an rf-powered stage. Since the ECR source can generate a plasma with low ion energy, dry etching induced damage is expected to be minimal. In this study, Schottky diodes and transmission lines were fabricated on the etched GaInAs surface. The diode and transmission line characteristics were evaluated as a function of etch conditions. For the etching of GaInAs and AllnAs, C12 and Ar were used as the etch gases. In addition to the ratio of the two gases, microwave power, rf power, pressure, and source distance were varied and their effects on etch rate, morphology, and surface damage were analyzed. Etch rate increased monotonically with microwave power, rf power, and C12 percentage. Etch rate decreased with increasing distance and reached a maximum for a pressure of 1 mTorr. The etch conditions for the damage study were chosen to maintain smooth morphology. One of the most important factors influencing damage was the ion energy which can be limited by using low rf power and short source distance. Minimum damage was obtained at 1 mTorr which provides the optimal balance between high etch rate and low ion energy. Besides limiting ion energy, the addition of Cl2 reduced etch-induced damage. The specific contact resistivity and sheet resistivity obtained from transmission line measurements of dryetched n-GaInAs were lower than the wet-etched samples. Schottky diode analysis show reduction in barrier height and breakdown voltage after Ar sputtering. Addition of 10% C12 is sufficient for full recovery of the diode characteristics.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 324: Symposium K – Diagnostic Techniques for Semiconductor Materials Processing , 1993 , 421
Copyright
Copyright © Materials Research Society 1994

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Foad, M. A., Thoms, S., and Wilkinson, C. D. W., J. Vac. Sci. Technol. B 11, 20 (1993).CrossRefGoogle Scholar
2. Seaward, K. L., and Moll, N. J., J. Vac. Sci. Technol. B 10, 46 (1992).Google Scholar
3. Benton, J. L., Weir, B. E., Eaglesham, D. J., and Gottscho, R. A., J. Vac. Sci. Technol. B 10, 540 (1992).CrossRefGoogle Scholar
4. He, L. and Anderson, W. A., Solid-State Electronics 35, 151 (1992).CrossRefGoogle Scholar
5. Pang, S. W., J. Electrochem. Soc. 133, 784 (1986).Google Scholar
6. Pearton, S. J., Chakrabarti, U. K., Perley, A. P., Constantine, C., and Johnson, D., Semicond. Sci. Technol. 6, 929 (1991).Google Scholar
7. Pearton, S. J., Chakrabarti, U. K., Hobson, W. S., Constantine, C., and Johnson, D., Nuclear Instruments and Methods in Physics Research B59/60, 1015 (1991).CrossRefGoogle Scholar
8. Noh, S. K., Ishibashi, K., Aoyagi, Y., Namba, S., and Yoshizako, Y., J. Appl. Phys. 67, 2591 (1990).CrossRefGoogle Scholar
9. Ren, F., Fullowan, T. R., Pearton, S. J., Lothian, J. R., Esagui, R., Abernathy, C. R., and Hobson, W. S., J. Vac. Sci. Technol. A 11, 1768 (1993).CrossRefGoogle Scholar
10. Pang, S. W. and Ko, K. K., J. Vac. Sci. Technol. B 10, 2703 (1992).Google Scholar
11. Reeves, G. K. and Harrison, H. B., IEEE Electron Device Letters EDL–3, 111 (1982).CrossRefGoogle Scholar
12. Kordos, P., M Marso, Meyer, R., and Ltith, H., J. Appl. Phys. 72, 2347 (1992).CrossRefGoogle Scholar