Hostname: page-component-8448b6f56d-qsmjn Total loading time: 0 Render date: 2024-04-24T14:04:29.376Z Has data issue: false hasContentIssue false
  • English
  • Français

Enhanced Plasticity of Mechanically Alloyed Aluminum IN90211

Published online by Cambridge University Press:  22 February 2011

T. R. Bieler ,
T. G. Nieh ,
J. Wadsworth  and
A. K. Mukherjee
T. R. Bieler
Affiliation:
Department of Mechanical Engineering, Division of Materials Science University of California, Davis CA 95616
T. G. Nieh
Affiliation:
Lockheed Missiles and Space Co. Inc., Research and Development Palo Alto, CA 94304
J. Wadsworth
Affiliation:
Lockheed Missiles and Space Co. Inc., Research and Development Palo Alto, CA 94304
A. K. Mukherjee
Affiliation:
Department of Mechanical Engineering, Division of Materials Science University of California, Davis CA 95616
Get access

Abstract

The tensile behavior of IN90211 was characterized at strain rates between 0.0001/sec and 340/sec at temperatures between 425 and 475 °C. At strain rates below 0.1/sec, the strain rate sensitivity m is about 0.027, with corresponding low elongation (<100%). At strain rates above 0.1/sec, the strain rate sensitivity increases to 0.26. A maximum elongation of 500% was obtained at 475 °C at a strain rate of 2.5/sec. Grain boundary sliding and rotation was observed on the highly elongated specimens and fracture surfaces exhibited intergranular fracture. Experimental data in the high strain rate regime (superplastic) revealed the existence of a temperature dependent threshold stress that seemed unrelated to the low stress deformation regime. This result is consistent with stress relaxation experiments. These threshold stresses are generally lower than those typically observed in other oxide dispersion strengthened (ODS) alloys. This observation is not expected from conventional superplastic creep theory.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 120: Symposium G – High-Temperature/High-Performance Composites , 1988 , 137
Copyright
Copyright © Materials Research Society 1988

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Nieh, T.G., Henshall, C.A., Wadsworth, J., Scripta Met., 18, 1405, (1984).CrossRefGoogle Scholar
2. Nieh, T.G., Gilman, P.S., Wadsworth, J., Scripta Met., 19, 1375, (1985).CrossRefGoogle Scholar
3. Bieler, T.R., Nieh, T.G., Wadsworth, J., Mukherjee, A.K., Scripta Met., 22, 81, (1988).CrossRefGoogle Scholar
4. Gregory, J.K., Gibeling, J.C., Nix, W.D., Met. Trans., 16A, 777, (1985).CrossRefGoogle Scholar
5. Mohamed, F.A., J. Mat. Sci., 18, 582, (1983).CrossRefGoogle Scholar
6. Shewfelt, R.S.W., Brown, L.M., Phil. Mag., 35, 945, (1977).CrossRefGoogle Scholar
7. McLean, M., Acta Met., 33, 545, (1985).CrossRefGoogle Scholar
8. Nardone, V.C., Matejczyk, D.E., Tien, J.K., Acta Met., 32, 1509, (1984).CrossRefGoogle Scholar
9. Arzt, E., Roesler, J., Schroeder, J.H., in Creep and Fracture of Engineering Materials and Structures, edited by Wilshire, B., Evans, R.W., (Institute of Metals, London, 1987), pp. 217–230.Google Scholar
10. Clauer, A.H., Hansen, N., Acta Met., 32, 269, (1984).CrossRefGoogle Scholar
11. Lund, R.W., Nix, W.D., Acta Met., 24, 467, (1976).CrossRefGoogle Scholar
12. Orowan, E., Internal Stresses in Metals and Alloys, (Institute of Metals, 1948), 451.Google Scholar
13. Bird, J.E., Mukherjee, A.K., Dorn, J.F., in Quantitative Relation Between Properties and Microstructure, (Israel University Press, Haifa, 1969), p. 255.Google Scholar
14. Chokshi, A.H., Bieler, T.R., Nieh, T.G., Wadsworth, J., Mukherjee, A.K., in Superplasticity in Aerospace Aluminum, Phoenix, AZ, AIME-TMS, 1988, in press.Google Scholar
15. Shaw, W.J.D., Mat. Letters, 4, 1, (1985).CrossRefGoogle Scholar
16. Hack, J.E., Page, R.A., Sherman, R., Met. Trans. 16A, 2069, (1985).CrossRefGoogle Scholar
17. Nutt, S.R., Carpenter, R.W., Mat. Sci. & Eng., 75, 169, (1985).CrossRefGoogle Scholar
18. Lea, C., Molinari, C., J. Mat. Sci., 19, 2336, (1984).CrossRefGoogle Scholar
19. Bane, S.J., Bradfield, J., Edwards, M.R., Mat. Sci. & Tech., 2, 1025, (1986).CrossRefGoogle Scholar
20. Howell, P.R. and Dunlop, G.L., in Creep and Fracture of Engineering Materials and Structures, edited by Wilshire, B. and Owen, D.R.J., (Pineridge Press, Swansea, U.K., 1981), pp. 127–140.Google Scholar
21. Suery, M., Mukherjee, A.K., in Creep Behavior of Crystalline Solids, edited by Wilshire, B. and Evans, R.W., (Pineridge Press, Swansea, U.K., 1984), p. 137.Google Scholar