Hostname: page-component-7bb8b95d7b-s9k8s Total loading time: 0 Render date: 2024-09-12T22:51:11.271Z Has data issue: false hasContentIssue false
  • English
  • Français

Dislocation Substructures in Shock-Loaded N13AI

Published online by Cambridge University Press:  22 February 2011

Diane E. Albert  and
T. George
Diane E. Albert
Affiliation:
Los Alamos National Laboratory, Los Alamos, NM 87545
T. George
Affiliation:
Los Alamos National Laboratory, Los Alamos, NM 87545
Get access

Abstract

The deformation substructure and mechanical response of the LI2 intermetallic, Ni3Al, subjected to shock-wave loading was studied. Following shock prestrains to shock pressures of approximately 14.0 GPa, 23.5 GPa, and 47.2 GPa, the reload yield strength of Ni3Al was measured to be 750 MPa, 1250 MPa and 1500 MPa, respectively. The effective hardening in the shock-loaded Ni3Al exceeds that quasistatically obtained when deformed to roughly the same equivalent strains. Coarse planar slip on {111} type planes, a high density of stacking faults, and deformation twins with a {111} type twinning plane were observed in the shocked material. An increasing propensity for twinning and stacking fault formation was observed with higher shock peak pressures.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 364: Symposium L – High-Temperature Ordered Intermetallic Alloys–VI , 1994 , 725
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Kear, B.H. and Wilsdorf, H.G.F., Trans. TMS-AIME, 224, 382 (1962).Google Scholar
2. Takeuchi, S. and Kuramoto, E., Acta metall. 21, 415 (1973).Google Scholar
3. Paidar, V., Pope, D.P. and Vitek, V., Acta metall. 32, 435 (1984).Google Scholar
4. Copley, S.M. and Kear, B.H., Trans. AIME 239, 977 (1967).Google Scholar
5. Umakoshi, Y., Pope, D.P., and Vitek, V., Acta metall. 32, 449 (1984).Google Scholar
6. Sizek, H.W. and Gray, G.T. III, Acta metall. mater. 41, 1855 (1993).Google Scholar
7. Sizek, H.W. and Gray, G.T. III in Shock-Wave and High-Strain-Rate Phenomena in Materials, edited by Meyers, M.A., Murr, L.E., and Staudhammer, K.P. (Marcel Dekker, NY, 1992) pp. 117–125.Google Scholar
8. Gray, G.T. III in High Pressure Shock Compression of Solids, edited by Asay, J.R. and Shahinpoor, M. (Springer-Verlag, NY, 1993) ch. 6.Google Scholar
9. Murr, L.E. in Shock Waves and High Strain Rate Phenomena in Metals, edited by Meyers, M.A. and Murr, L.E. (Plenum Press, NY, 1981) p. 607.Google Scholar
10. Albert, D.E. and Gray, G.T. III, Phil Mag., to be published Google Scholar
11. Albert, D.E. and Gray, G.T. III,Phil. Mag., 70, 145 (1994).Google Scholar
12. Christian, J.W. and Laughlin, D.E., Acta metall, 36, 1617 (1988).Google Scholar
13. Yoo, M.H., J. Mater. Res. 4, 50 (1989).Google Scholar
14. Chu, F. and Pope, D.P., Mater. Sci. Engng., A170, 39 (1993).Google Scholar
15. Kear, B.H., Giamei, A.F., and Oblak, J.M., Scripta metall. 4, 567 (1970).Google Scholar
16. Kear, B.H., Oblak, J.M., and Giamei, A.F., Metall. Trans. A 1, 2477 (1970).Google Scholar
17. Yamaguchi, M., Vitek, V., and Pope, D.P., in Dislocation Modelling of Physical Systems, edited by Ashby, M.F., Bullough, R., Hartley, C.S., and Hirth, J.P. (Pergamon Press, NY, 1981) pp. 280–284.Google Scholar