Hostname: page-component-7479d7b7d-767nl Total loading time: 0 Render date: 2024-07-11T07:26:05.021Z Has data issue: false hasContentIssue false
  • English
  • Français

Diffusion and Pore Structure in Portland Cement Pastes Blended with Low Calcium Fly Ash

Published online by Cambridge University Press:  25 February 2011

Amitabha Kumar  and
Della M. Roy
Amitabha Kumar
Affiliation:
Materials Research Laboratory, The Pennsylvania State University, University Park, PA 16802, USA
Della M. Roy
Affiliation:
Materials Research Laboratory, The Pennsylvania State University, University Park, PA 16802, USA Also affiliated with the Department of Materials Sciences and Engineering
Get access

Abstract

Effective coefficients for the diffusion of Cs+ and Cl− ions accross hardened plates of Portland cement and Portland cement-fly ash blend pastes were measured at 27°, 38° and 60° for samples cured up to 28 d. The porosity and pore size distributions of the same hardened plates were also determined. The fly ash blends show lower anion and cation diffusion rates at higher temperatures, although the porosity is not significantly different from the neat paste. The finer pore size is considered responsible for the slower diffusion in the blends. The electronegative nature of the pore surfaces also contributes to the slower cation diffusion.

Type
Articles
Information
MRS Online Proceedings Library (OPL) , Volume 65: Symposium T – Fly Ash and Coal Conversion By-Products II , 1985 , 227
Copyright
Copyright © Materials Research Society 1986

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Kumar, A. and Roy, D.M., J. Am. Cer. Soc. 67, 61–64 (1984).CrossRefGoogle Scholar
2. Page, C.L., Short, N.R. and Tarras, A. El, Cem. Concr. Res. 11, 395–406 (1981).Google Scholar
3. Hooton, R.D., in ASTM C-1 Symposium on Blended Cements, Denver, CO (June 27, 1984). Preliminary report.Google Scholar
4. Kumar, A. and Roy, D.M., J. Am. Cer. Soc. 69(April, 1986).Google Scholar
5. Roy, D.M., Kumar, A. and Rhodes, J.P., in Proc. Second Intl. Conf. on the Use of Fly Ash, Silica Fume, Slag and Natural Pozzolanas in Concrete, CANMET, ICEF and ACI, Madrid, Spain (April 21–25, 1986).Google Scholar
6. Mehta, P.R. and Gjørv, O.E., Cem. Concr. Res. 12, 587–595 (1981).Google Scholar
7. Smolcyzk, H.G., Betonwerk und Fertigteil-Technik, 12, 7 (1984).Google Scholar
8. Kumar, A., Diffusion and Pore Structure Studies in Cementitious Materials, Ph.D. Thesis, Solid State Science, The Pennsylvania State University, University Park, PA (1985).Google Scholar
9. Kumar, A. and Roy, D.M., Cem. Concr. Res. 16, 74–78 (1986).CrossRefGoogle Scholar
10. Goto, S. and Roy, D.M., Cem. Concr. Res. 11, 751–757 (1981).Google Scholar
11. Feldman, R.F., J. Am. Cer. Soc. 67, 30–33 (1984).Google Scholar
12. Roy, D.M. and Parker, K.M., Proc. CANMET/ACI First Intl. Conf. on the Use of Fly Ash, Silica Fume, Slag and Other Mineral By-Products in Concrete, Vol. I, Ed. Malhotra, V.M., ACI SP-79, (American Concrete Instutute, Detroit, 1983) pp. 397–414Google Scholar