Hostname: page-component-77c89778f8-7drxs Total loading time: 0 Render date: 2024-07-19T15:41:05.937Z Has data issue: false hasContentIssue false

Cracking in the Weld Heat-Affected Zone of COntinuously Cast Sheet and Ingot of Ni3Al

Published online by Cambridge University Press:  26 February 2011

Huaxin Li
Affiliation:
State University of New York, Department of Mechanical and Aerospace Engineering, Buffalo, NY 14260
T.K. Chaki
Affiliation:
State University of New York, Department of Mechanical and Aerospace Engineering, Buffalo, NY 14260
Get access

Abstract

Weldability is a key issue for successful applications of ductile Ni3Al in structural components. Here we report the results of an investigation of gas tungsten arc welding behaviors of continuously cast thin sheet and cast ingot of a Ni3Al alloy, known as IC-50, containing boron and zirconium. Cracking in heat-affected zone (HAZ) was prevalent in both types of specimens. Both in cast sheet and ingot, liquation cracking was observed to occur along the grain boundaries in HAZ. Microstructural studies showed that continuously cast thin sheet consisted of columnar grains along the thickness. Easy cracking along the boundaries of columnar grains made cast sheets more susceptible to hot cracking than ingots. The possibility of segregation of boron and zirconium, causing liquation cracking, will be discussed.

Type
Research Article
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Copley, S. M. and Kear, B. H., Trans. The Metall. Soc. - AIME, 239, 977 (1967).Google Scholar
[2] Liu, C. T., in High Temperature Ordered Intermetallic Alloys II, edited by Stoloff, N. S., Koch, C. C., Liu, C. T., and Izumi, O. (Materials Research Society, Pittsburgh, 1987), p. 355.Google Scholar
[3] Aoki, K. and Izumi, O., Nippon Kinzoku Gakkaishi, 43, 1190 (1979).Google Scholar
[4] Liu, C. T., White, C. L., and Horton, J. A., Acta Metall., 33, 213 (1985)CrossRefGoogle Scholar
[5] Schulson, E. M., Weihs, T. P., Baker, J., Frost, H. J., and Horton, J. A., Acta Metall., 34, 1395 (1986).CrossRefGoogle Scholar
[6] Chaki, T. K., Philos. Mag. Lett.,61, 5 (1990).CrossRefGoogle Scholar
[7] Chaki, T. K., unpublished.Google Scholar
[8] Kruisman, J. J., Vitek, V., and Th, J.. De Hosson, M., Acta Metall., 36, 2729 (1988).CrossRefGoogle Scholar
[9] Liu, C. T., Sikka, V. K., Horton, J. A., and Lee, E. H., in Alloy Develop ment and Mechanical Properties of Nickel Aluminide (Ni3Al) Alloys Report no. 6483, Oak Ridge National Laboratory, Oak Ridge, TN, August 1988.Google Scholar
[10] David, S. A., Jemian, W. A., Liu, C. T., and Horton, J. A., Welding Journal, 64, 22-s (1985).Google Scholar
[11] Santella, M. L. and David, S. A., Welding Journal, 65, 124-s (1986).Google Scholar
[12] Santella, M. L., Horton, J. A., and David, S. A., Welding Journal, 67, 63-s (1988).Google Scholar
[13] Owczarski, W. A., Duvall, D. S., and Sullivan, C. P., Welding Journal, 46, 423-s (1967).Google Scholar
[14] RadhaKrishnan, B. and Thompson, R. G., Scripta Metall. Mat., 24, 537 (1990).Google Scholar
[15] Tamura, M., in Superalloys, Supercomposites and Superceramics, edited by Tien, J. K. and Caulfield, T. (Academic Press, New York, 1989), p. 215.Google Scholar
[16] Sikka, V. K., private communication, 1990.Google Scholar