Hostname: page-component-76fb5796d-dfsvx Total loading time: 0 Render date: 2024-04-26T14:46:53.031Z Has data issue: false hasContentIssue false
  • English
  • Français

Correlation of Strain Hardening and Creep Behaviour of γ-TiAl

Published online by Cambridge University Press:  01 January 1992

A. Bartels ,
J. Seeger  and
H. Mecking
A. Bartels
Affiliation:
Devision of Physics and Technology of Materials, Technical University of Hamburg-Harburg, D-2100 Hamburg 90, Germany
J. Seeger
Affiliation:
Devision of Physics and Technology of Materials, Technical University of Hamburg-Harburg, D-2100 Hamburg 90, Germany
H. Mecking
Affiliation:
Devision of Physics and Technology of Materials, Technical University of Hamburg-Harburg, D-2100 Hamburg 90, Germany
Get access

Abstract

Compression tests on Ti-48AI-2Cr were performed in the temperature range of 650-1000°C. The stress vs. strain curves show an initial increase with a decreasing rate due to dynamic recovery. In the second stage, correlated with dynamic recrystallization (DRX), the stress passes through a maximum and decreases to a steady state value. The characteristic steady state stress associated with dynamic recovery exhibits a lower activation energy (269 kJ/mol) than the steady state stress during DRX (400 kJ/mol). Constant-load creep experiments show a corresponding behaviour. After primary creep the creep rate passes through a minimum. The final steady state creep conditions are dominated by DRX as well.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 288: Symposium L – High-Temperature Ordered Intermetallic Alloys V , 1992 , 1179
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Huang, S. C. and Hall, E. L., Metall. Trans. A22, 2619 (1991)Google Scholar
2. Kim, Y.-W. and Dimiduk, D. M., JOM 43, 40 (1991)Google Scholar
3. Wurzwallner, K., Clemens, H., Schretter, P., Bartels, A. and Koeppe, C., in High Temperature Ordered Intermetallic Alloys V, (Mater. Res. Soc. Proc.) this proceedingsGoogle Scholar
4. Seeger, J., Bartels, A. and Mecking, H., Scripta Metall. Mater. 25, 2523 (1991)Google Scholar
5. Koeppe, C., Seeger, J., Bartels, A. and Mecking, H., submitted to Metall. Trans. A (1992)Google Scholar
6. Dieter, G. E., Mechanical Metallurgy, (MacGraw-Hill International Editions, New York, 1986)Google Scholar
7. Bartels, A. and Mecking, H., in Ordered Intermetallics - Physical Metallurgy and Mechanical Behaviour, ed. by Liu, C. T., Cahn, R. W., Sauthoff, G., NATO ASI Series E, Vol. 213 (Kluwer Academics Publisher, Dordrecht, 1992) pp. 663–678 Google Scholar
8. Seeger, J., Doktor thesis Technical University of Hamburg-Harburg, 1993 Google Scholar
9. Mecking, H., Nicklas, B., Zarubova, N. and Kocks, U. F., Acta metall. 34, 527 (1986)Google Scholar
10. Mecking, H. and Gottstein, G., in Recrystallization of Metallic Materials, ed. Haessner, F. (Dr. Rieder-Verlag GmbH, Stuttgart, 1978) pp.195–222 Google Scholar
11. Kroll, H. Mehrer, Stowijk, N., Herzig, C., Rosenkranz, R. and Frommeyer, G., Z. Metallkd. 83, 591(1992)Google Scholar
12. Oikawa, H., Mater. Sci. Eng. A153, 427 (1992)Google Scholar
13. McQueen, H. J. and Jonas, J. J., in Treaties of Materials Science and Technology, ed. Arsenault, R., (Academic Press, New York, 1975) pp.393–493 Google Scholar
14. Es-Souni, M., Bartels, A. and Wagner, R., to be publishedGoogle Scholar