Hostname: page-component-7479d7b7d-wxhwt Total loading time: 0 Render date: 2024-07-11T00:30:59.187Z Has data issue: false hasContentIssue false
  • English
  • Français

CdTe Thin Film Solar Cells: The CdS/SnO2 Front Contact

Published online by Cambridge University Press:  21 March 2011

J. Fritsche ,
S. Gunst ,
A. Thiβen ,
R. Gegenwart ,
A. Klein  and
W. Jaegermann
J. Fritsche
Affiliation:
Institute of Materials Science, Darmstadt University of TechnologyPetersenstrasse 23, 64287 Darmstadt, Germany
S. Gunst
Affiliation:
Institute of Materials Science, Darmstadt University of TechnologyPetersenstrasse 23, 64287 Darmstadt, Germany
A. Thiβen
Affiliation:
Institute of Materials Science, Darmstadt University of TechnologyPetersenstrasse 23, 64287 Darmstadt, Germany
R. Gegenwart
Affiliation:
ANTEC Technology GmbH Arnstädter Str. 22, D-99334 Rudisleben/Thür., Germany
A. Klein
Affiliation:
Institute of Materials Science, Darmstadt University of TechnologyPetersenstrasse 23, 64287 Darmstadt, Germany
W. Jaegermann
Affiliation:
Institute of Materials Science, Darmstadt University of TechnologyPetersenstrasse 23, 64287 Darmstadt, Germany
Get access

Abstract

Tin dioxide (SnO2) coated glass is the commonly used substrate for thin film solar cells based on CdTe absorbers. We have investigated the properties of the CdS/SnO2 interface by X-ray and ultraviolet photoelectron spectroscopy. SnO2 coated glass substrates as used for solar cell preparation were cleaned by different procedures such as derinsing, sputtering, heating and annealing in oxygen atmosphere. Different surface properties with a strongly dependent number of defects in the SnO2 band gap are identified. CdS films were deposited stepwise by thermal evaporation to determine the electronic interface properties for different surface preparation conditions. Comparative barrier heights at the CdSSnO2 contact are found for most surface pretreatments. The Fermi level position in these cases is situated in the SnO2 band gap. A different interface behaviour is determined for sputter cleaned SnO2 surfaces, which is attributed to the formation of oxygen vacancies during sputtering and subsequent formation of an interfacial SnOxSy compound.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 668: Symposium H – II-IV Compound Semiconductor Photovoltaic Materials , 2001 , H5.1
Copyright
Copyright © Materials Research Society 2001

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Chu, T.L., Current Topics in Photovoltaics 3 (1988) 235 Google Scholar
2. Zweibel, K., Mitchell, R., Advances in Solar Energy 6 (1991) 485 Google Scholar
3. Bloss, W.H., Pfisterer, F., Schubert, M., Walter, T., Prog. Photovolt. Res. Appl. 3 (1995) 11 Google Scholar
4. Bonnet, D., Harr, M., Proc. of the 2nd Int. Conf. on Photovoltaic Solar Energy Conv. 1 (1998) 397 Google Scholar
5. Bonnet, D., Thin Solid Films 361–362, 547–552 (2000).Google Scholar
6. Niles, D. W., Rioux, D., and Höchst, H., J. Appl. Phys. 73, 4586 (1993).Google Scholar
7. Fritsche, J., Thißen, A., Klein, A., and Jaegermann, W., Thin Solid Films 387, 158 (2001).Google Scholar
8. Fritsche, J., Gunst, S., Golusda, E., Lejard, M.C., Thißen, A., Mayer, T., Wendt, R., Gegenwart, R., Bonnet, D., Klein, A., and Jaegermann, W., Thin Solid Films 387, 161 (2001).Google Scholar
9. Klein, A., Appl. Phys. Lett. 77, 2009–2011 (2000).Google Scholar
10. Madelung, O., Semiconductors-Basic Data, Springer (1996)Google Scholar