Hostname: page-component-7479d7b7d-q6k6v Total loading time: 0 Render date: 2024-07-11T05:31:23.592Z Has data issue: false hasContentIssue false

C2H4-Based Plasma-Assisted CD Shrink and Contact Patterning for RRAM Application

Published online by Cambridge University Press:  01 February 2011

Alexey Milenin
Affiliation:
milenin@imec.be, IMEC, EtchFeol, Leuven, Belgium
Judit Lisoni
Affiliation:
Judit.Lisoni@imec.be, IMEC, Leuven, Belgium
Nico Jossart
Affiliation:
Nico.Jossart@imec.be, IMEC, Leuven, Belgium
Malgorzata Jurczak
Affiliation:
Malgorzata.Jurczak@imec.be, IMEC, Leuven, Belgium
Herbert Struyf
Affiliation:
Herbert.Struyf@imec.be, IMEC, Leuven, Belgium
Denis Shamiryan
Affiliation:
Denis.Shamiryan@imec.be, IMEC, Leuven, Belgium
Mohand Brouri
Affiliation:
Mohand.Brouri@imec.be, Lam, Leuven, Belgium
Werner Boullart
Affiliation:
Werner.Boullart@imec.be, IMEC, Leuven, Belgium
Get access

Abstract

Critical dimension (CD) shrink and patterning of contact features via plasma etching were studied for typical resistive random access memory (RRAM) stacks. These consist of SiO2 and Si3N4 (total thickness of 65 80 nm) with NiO or pure Ni at the bottom. First, the contact patterning of RRAM stacks was investigated for 90 nm contacts. Thus, a standard high power contact etch recipe was shown to give rise to resist strip challenges due to the incorporation of sputtered Ni in the resist film. Therefore, a low-sputter-yield contact etch recipe based on a CF4/H2/Ar gas chemistry was introduced. The ion sputter efficiency of the recipe was estimated from a blanket SiO2 sputter-yield experiment in Ar plasma for the same recipe settings: this yielded values close to the Ni sputter-yield threshold. Second, plasma-assisted CD shrink was studied in combination with the newly developed patterning scheme to get the contact CD well below the initial 90-nm litho print size. It was shown that a low contact etch power regime could also provide a larger window for contact CD shrink using a C2H4-based chemistry: e.g. the demonstrated CD shrink from 90 nm down to sub-40 nm was shown to be extremely challenging in the case of a high power regime due to polymer instability enhanced with the resulting thickness increase. Perhaps, the relaxation of the polymer film stress, which was measured to be in the range of 1200-1500 MPa, is more easily triggered at higher power settings, which leads to polymer blistering. Finally, the optimization of the plasma-assisted CD shrink step in combination with the low-sputter-yield contact etch recipe was demonstrated to be able to provide CDs as small as 27 nm. The demonstrated approach shows that plasma-assisted CD shrink can provide a robust test vehicle for research programs that require the patterning of small features in the sub-40-nm CD range.

Type
Research Article
Copyright
Copyright © Materials Research Society 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1 Lisoni, J., et al., “Oxidation behavior of Ni thin films: application to NiO-based ReRAM”, MRS Spr.Mt. H10.9, (2009).Google Scholar
2 Koehler, M., “Etching in Microsystem Technology”, Wiegrand, A., Trans., Wiley-VCH, (New York, 1999) pp. 283285.Google Scholar
3 Ohmori, T., Kamata, T., Kitajima, T. and Makabe, T., Jap. J. Appl. Phys. 44/35, L 1105–L 1108 (2005).Google Scholar
4 Matsui, J., Nakano, N., Petrovic, Z. Lj., and Makabe, T., Appl.Phys.Lett. 78/7, 883885 (2001).Google Scholar
5 Arnold, J.C. and Sawin, H.H., J.Appl.Phys. 70/10, 53145317 (1991).Google Scholar
6 Yin, Y. and Sawin, H.H., J. Vac. Sci. Technol. A 26(1), 151160 (2008).Google Scholar
7 Hundur, Y., Guevenc, Z., Hippler, R., Chin.Phys.Lett. 25/2 730733 (2008).Google Scholar
8 Keddie, J.L., Jones, R., Cory, R.A., Europhys. Lett. 27, 5964 (1994).Google Scholar