Hostname: page-component-7479d7b7d-k7p5g Total loading time: 0 Render date: 2024-07-12T04:32:48.318Z Has data issue: false hasContentIssue false
  • English
  • Français

Nondestructive Measurement of In-Plane Residual Stress in Silicon Strips

Published online by Cambridge University Press:  10 February 2011

Tieyu Zheng  and
Steven Danyluk
Tieyu Zheng
Affiliation:
The George Woodruff Mechanical Engineering School, Georgia Institute of Technology, Atlanta, GA 30332
Steven Danyluk
Affiliation:
The George Woodruff Mechanical Engineering School, Georgia Institute of Technology, Atlanta, GA 30332
Get access

Abstract

This paper reports the development of a shadow moiré technique to measure the in-plane residual stresses of thin, flat strips. This is an extension of prior work on the measurement of in-plane residual stresses in silicon plates and wafers. Phase stepping shadow moir6 and digital image processing techniques are employed to measure the deflections of the silicon plate specimens subjected to three-point-bending at several different loads. The measured deflections over the area of the silicon plates are fitted with an equation represented by a 2-D polynomial. With the theory of thin plates with large deflection, the fitting coefficients are used to extract the in-plane stresses at the different bending load. The residual stress is resolved by linear regression of the in-plane stresses versus bending loads.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 591 , 1999 , 283
Copyright
Copyright © Materials Research Society 2000

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Andonian, A. T., Danyluk, S., J. Mater. Sci. 20, p. 4459–4464 (1985)Google Scholar
2.Andonian, A. T., Danyluk, S., Mech. Res. Com. 11(2), p. 97–104 (1984)Google Scholar
3.LaFontaine, W. R., Yost, B., Li, C. Y., J. Mater. Res. 5(4), p. 776–783 (1990)Google Scholar
4.Chen, L. D., Zhang, M. J., Zhang, S., J. Appl. Phys. 76(3), p. 1547–1551 (1994)Google Scholar
5.Renninggen, M., J. Appl. Crypt. 5, 163-169 (1972)Google Scholar
6.Majumdas, S., Kupperman, D., Singh, J., J. Amer. Ceram. Soc. 71(10), p. 858–863 (1988)Google Scholar
7.Zheng, T., Danyluk, S., Proc. SEM Annu. Conf. on Theo., Exper. and Comp. Mech., p. 391–394 (1999)Google Scholar
8.Chiang, F. P., Kobayashi, A. S., Manual of Experimental Stress Analysis, 3rd ed., (Bookfield Center, 1978)Google Scholar
9.Timoshenko, S. P., Woinowsky-Kreiger, S., Theory of Plates and Shells, (Puli. McGraw Hill, 1959)Google Scholar
10.Creath, K., Wolf, E., Progress in Optics XXVI, (Elsevier Science Publishers B.V., 1988)Google Scholar
11.Wortman, J. J., Evans, R. A., J. Appl. Phys. 36(1), p. 153–156 (1965)Google Scholar
12.O'Mara, W. C., Herring, R. B., Hunt, L. P., Handbook of Semiconductor Silicon Technology, (Noyes Publications, 1990)Google Scholar