Hostname: page-component-848d4c4894-nr4z6 Total loading time: 0 Render date: 2024-06-11T01:49:55.249Z Has data issue: false hasContentIssue false
  • English
  • Français

Models of Magnesium Oxide (111) Surface Reconstructions Obtained from Direct Phasing of Transmission Electron Diffraction Data

Published online by Cambridge University Press:  02 July 2020

R. Plass ,
K. Egan ,
C. Collazo-Davila ,
D. Grozea ,
E. Landree ,
L. D. Marks  and
M. Gajdardziska-Josifovska
R. Plass
Affiliation:
Department of Physics, University of Wisconsin at Milwaukee, Milwaukee, WI53211
K. Egan
Affiliation:
Department of Physics, University of Wisconsin at Milwaukee, Milwaukee, WI53211
C. Collazo-Davila
Affiliation:
Department of Mat. Science and Eng., Northwestern University, Evanston, IL, 60208
D. Grozea
Affiliation:
Department of Mat. Science and Eng., Northwestern University, Evanston, IL, 60208
E. Landree
Affiliation:
Department of Mat. Science and Eng., Northwestern University, Evanston, IL, 60208
L. D. Marks
Affiliation:
Department of Mat. Science and Eng., Northwestern University, Evanston, IL, 60208
M. Gajdardziska-Josifovska
Affiliation:
Department of Physics, University of Wisconsin at Milwaukee, Milwaukee, WI53211
Get access

Extract

It has long been thought that (111) surfaces of rock salt oxides microfacet to neutral surfaces upon annealing because of the very large energies involved in bulk terminating a layer of like ions. However in a recent reflection electron microscopy (REM) study Gajdardziska-Josifovska et al. found that MgO(lll) surfaces annealed in flowing oxygen furnaces at 1500°C not only did not microfacet, but displayed a √3×√3R30° surface periodicity that was stable in air. To determine the structure of this unusually stable surface MgO (111) transmission electron microscopy (TEM) samples were annealed in a vacuum furnace in the present study and their transmission electron diffraction (TED) patterns were analyzed with direct phasing methods.

The TEM samples were prepared by orienting a MgO single crystal and sawing lmm wafers along a (111) plane. Disk samples were then ultrasonically drilled, dimpled, mechanically polished and/or hot nitric acid etched, and milled with 5 KeV Ar+ ions.

Type
Electron Crystallography; the Electron Phase Problem
Information
Microscopy and Microanalysis , Volume 3 , Issue S2: Proceedings: Microscopy & Microanalysis '97, Microscopy Society of America 55th Annual Meeting, Microbeam Analysis Society 31st Annual Meeting, Histochemical Society 48th Annual Meeting, Cleveland, Ohio, August 10-14, 1997 , August 1997 , pp. 1039 - 1040
Copyright
Copyright © Microscopy Society of America 1997

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Heinrich, V.E., Surf. Sci., 57(1976)385.10.1016/0039-6028(76)90190-4CrossRefGoogle Scholar
2.Tasker, P.W., J. Phys. C., 12(1979)4977.10.1088/0022-3719/12/22/036CrossRefGoogle Scholar
3.Gajdardziska-Josifovska, M., et al., Surf. Sci. Lett., 248 (1991) L259.Google Scholar
4.Marks, L. D., et al., Surf. Rev. and Lett., (1996) in press.Google Scholar
5.Landree, E., et al., Acta Cryst. B, (1996) submitted.Google Scholar