Hostname: page-component-84b7d79bbc-g5fl4 Total loading time: 0 Render date: 2024-07-25T15:46:30.344Z Has data issue: false hasContentIssue false

Plastic Flow Instabilities of L12 Ni3(Si,Ti) Alloys at Intermediate Temperature

Published online by Cambridge University Press:  31 January 2011

H. Honjo
Affiliation:
Department of Metallurgy and Materials Science, Graduate School of Engineering, Osaka Prefecture University, Gauken-cko 1–1, Sakai, Osaka, 599–8531, Japan
Y. Kaneno
Affiliation:
Department of Metallurgy and Materials Science, Graduate School of Engineering, Osaka Prefecture University, Gauken-cko 1–1, Sakai, Osaka, 599–8531, Japan
H. Inoue
Affiliation:
Department of Metallurgy and Materials Science, Graduate School of Engineering, Osaka Prefecture University, Gauken-cko 1–1, Sakai, Osaka, 599–8531, Japan
T. Takasugi
Affiliation:
Department of Metallurgy and Materials Science, Graduate School of Engineering, Osaka Prefecture University, Gauken-cko 1–1, Sakai, Osaka, 599–8531, Japan
Get access

Abstract

The serrated plastic flow of L12 Ni3 (Si,Ti) alloys at intermediate temperature was investigated by tensile tests in terms of the effects of temperature, strain rate, composition, and microstructure. Serrated plastic flow was most strongly observed at 473 K and at a strain rate of 1.6 × 10–4 s–1. Correspondingly, the maximum stress amplitude and the lowest (negative) strain-rate sensitivity were observed at 473 K. Serrated plastic flow took place irrespective of boron doping and was more significant in a fine-grained Ni3 (Si,Ti) alloy. The static aging at 473 K resulted in reduced flow stress. The activation energy for serrated plastic flow was estimated to be about 57 kJ mol–1, suggestive of being smaller than that for lattice diffusion of solutes. The serrated plastic flow behavior of Ni3 (Si,Ti) alloys was compared with that of L12 Co3Ti alloys, and is qualitatively explained on the basis of the dynamics of solutes in the core of a dissociated screw dislocation.

Type
Articles
Copyright
Copyright © Materials Research Society 2002

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Veyssiere, P. and Saada, G., in Dislocations in Solids, edited by Nabarro, F.R.N. and Duesbery, M.S. (North-Holland, Amsterdam, The Netherlands, 1996), Chapter 53, p. 254.Google Scholar
Pope, D.P. and Ezz, S.S., Int. Mater. Rev. 29, 136 (1984).CrossRefGoogle Scholar
Stoloff, N.S., Int. Mater. Rev. 34, 153 (1989).CrossRefGoogle Scholar
Yamagauchi, M. and Umakoshi, Y., Prog. Mater. Sci. 34, 1 (1990).CrossRefGoogle Scholar
Suzuki, T., Mishima, Y., and Miura, S., ISIJ Int. 29, 1 (1989).CrossRefGoogle Scholar
Kear, B.H. and Wilsdorf, H.G.F., Trans. Metall. Soc. AIME 224, 382 (1962).Google Scholar
Paidar, V., Pope, D.P., and Vitek, V., Acta Metall. 32, 435 (1984).CrossRefGoogle Scholar
Takeuchi, S. and Kuramoto, E., Acta Metall. 21, 415 (1973).CrossRefGoogle Scholar
Yoo, M.H., Scr. Metall. 20, 915 (1986).CrossRefGoogle Scholar
Hall, E.O., Yield Point Phenomena in Metals and Alloys (Plenum, New York, 1970).CrossRefGoogle Scholar
Potez, I., Lapasset, G., and Kubin, L.P., Scr. Metall. Mater. 26, 84 (1992).CrossRefGoogle Scholar
Dinhut, J.F., Bonou, T., and Moine, P., Acta Metall. 24, 445 (1976).CrossRefGoogle Scholar
Lerf, R. and Morris, D.G., Acta Metall. Mater. 42, 1091 (1994).CrossRefGoogle Scholar
Mabuchi, H., Hirukawa, K., Katayama, K., Tsuda, H., and Nakayama, Y., Scr. Metall. 24, 1553 (1990).CrossRefGoogle Scholar
George, E.P., Pope, D.P., Fu, C.L., and Schneibel, J.H., ISIJ Int. 31, 1063 (1991).CrossRefGoogle Scholar
Takasugi, T., Honjo, H., Kaneno, Y., and Inoue, H., Acta Mater. 505, 847 (2002).CrossRefGoogle Scholar
Takasugi, T., Watanabe, S., Izumi, O., and Fat-Halla, H.K., Acta Metall. 37, 3425 (1989).CrossRefGoogle Scholar
Yoshida, M. and Takasugi, T., Philos. Mag. 65, 41 (1992).CrossRefGoogle Scholar
Takasugi, T. and Yoshida, M., Philos. Mag. 65, 613 (1992).CrossRefGoogle Scholar
Cottrell, A.H., Dislocations and Plastic Flow in Crystals (Clarendon Press, Oxford, United Kingdom, 1953).Google Scholar
Takasugi, T., Nagashima, M., and Izumi, O., Acta Metall. Mater. 38, 747 (1990).CrossRefGoogle Scholar
Takasugi, T., Hono, K., Suzuki, S., Hanada, S., and Sakurai, T., Scr. Metall. Mater. 29, 1587 (1993).CrossRefGoogle Scholar