Skip to main content Accessibility help

Equal channel angular extrusion for bulk processing of Fe–Co–2V soft magnetic alloys, part II: Texture analysis and magnetic properties

  • Andrew B. Kustas (a1), Joseph R. Michael (a1), Don F. Susan (a1), Ibrahim Karaman (a2) and Taymaz Jozaghi (a3)...


In Part I, equal channel angular extrusion (ECAE) was demonstrated as a novel, simple-shear deformation process for producing bulk forms of the low ductility Fe–Co–2V (Hiperco 50A®) soft ferromagnetic alloy with refined grain sizes. Microstructures and mechanical properties were discussed. In this Part II contribution, the crystallographic textures and quasi-static magnetic properties of ECAE-processed Hiperco were characterized. The textures were of a simple-shear character defined by partial {110} and 〈111〉 fibers inclined relative to the extrusion direction, in agreement with the expectations for simple-shear deformation textures of BCC metals. These textures were observed throughout all processing conditions and only slightly reduced in intensity by subsequent recrystallization heat treatments. Characterization of the magnetic properties revealed a lower coercivity and higher permeability for ECAE-processed Hiperco specimens relative to the conventionally processed and annealed Hiperco bar. The effects of the resultant microstructure and texture on the coercivity and permeability magnetic properties are discussed.


Corresponding author

a)Address all correspondence to this author. e-mail:


Hide All
1.Sourmail, T.: Near equiatomic FeCo alloys: Constitution, mechanical and magnetic properties. Prog. Mater. Sci. 50, 816 (2005).
2.Sundar, R.S. and Deevi, S.C.: Soft magnetic FeCo alloys: Alloy development, processing, and properties 50, 157192 (2005).
3.Carpenter: CarTech® Hiperco® 50A Alloy (2017).
4.Sundar, R.S., Deevi, S.C., and Reddy, B.V.: High strength FeCo–V intermetallic alloy: Electrical and magnetic properties. J. Mater. Res. 20, 1515 (2005).
5.Storch, M.L., Rollett, A.D., and McHenry, M.E.: The effect of mechanical working on the in-plane magnetic properties of Hiperco 50. J. Appl. Phys. 85, 6040 (1999).
6.Valiev, R.Z., Sabirov, I., Zhilyaev, A.P., and Langdon, T.G.: Bulk nanostructured metals for innovative applications. JOM 64, 1134 (2012).
7.Segal, V.M.: Materials processing by simple shear. Mater. Sci. Eng., A 197, 157 (1995).
8.Segal, V.M.: Engineering and commercialization of equal channel angular extrusion (ECAE). Mater. Sci. Eng., A 386, 269 (2004).
9.Valiev, R.Z. and Langdon, T.G.: Principles of equal-channel angular pressing as a processing tool for grain refinement. Prog. Mater. Sci. 51, 881 (2006).
10.Cullity, B. and Graham, C.: Introduction to magnetic materials, 2nd Ed. (2009); pp. 201–202.
11.Bunge, H.J.: Texture and magnetic properties. Textures Microstruct. 11, 75 (1989).
12.Pfeifer, F. and Radeloff, C.: Session 5: Ni–Fe and Co–Fe alloys—Some physical and metallurgical aspects. J. Magn. Magn. Mater. 19, 190 (1980).
13.Hutchinson, W.B. and Swift, J.G.: Anisotropy in some soft magnetic materials. Texture 1, 117 (1972).
14.Rollett, A.D., Storch, M.L., Hilinski, E.J., and Goodman, S.R.: Approach to saturation in textured soft magnetic materials. Metall. Mater. Trans. A 32, 2595 (2001).
15.Kustas, A.B., Sagapuram, D., Trumble, K.P., and Chandrasekar, S.: Texture development in high-silicon iron sheet produced by simple shear deformation. Metall. Mater. Trans. A 47, 3095 (2016).
16.Kustas, A.B., Chandrasekar, S., and Trumble, K.P.: Magnetic properties characterization of shear-textured 4 wt% Si electrical steel sheet. J. Mater. Res. 31, 3930 (2016).
17.Goss, N.P.: New development in electrical strip steels characterized by fine grain structure approaching the properties of a single crystal. Trans. ASM 23, 511 (1935).
18.Mishra, S., Därmann, C., and Lücke, K.: On the development of the goss texture in iron–3% silicon. Acta Metall. 32, 2185 (1984).
19.Hall, R.C.: Magnetic anisotropy and magnetostriction of ordered and disordered cobalt–iron alloys. J. Appl. Phys. 157, 110 (1960).
20.Niendorf, T., Canadinc, D., Maier, H.J., and Karaman, I.: The role of heat treatment on the cyclic stress-strain response of ultrafine-grained interstitial-free steel. Int. J. Fatig. 30, 426 (2008).
21.Yapici, G.G., Beyerlein, I.J., Karaman, I., and Tomé, C.N.: Tension-compression asymmetry in severely deformed pure copper. Acta Mater. 55, 4603 (2007).
22.Beyerlein, I.J. and Tóth, L.S.: Texture evolution in equal-channel angular extrusion. Prog. Mater. Sci. 54, 427 (2009).
23.Haouaoui, M., Karaman, I., and Maier, H.J.: Flow stress anisotropy and Bauschinger effect in ultrafine grained copper. Acta Mater. 54, 5477 (2006).
24.Barber, R.E., Dudo, T., Yasskin, P.B., and Hartwig, K.T.: Product yield for ECAE processing. Scr. Mater. 51, 373 (2004).
25.Segal, V., Goforth, R., and Hartwig, K.T.: Apparatus and method for deformation processing of metals, ceramics, plastics and other materials. U.S. Patent No. 5,400,633, 1995.
26.Clegg, D.W. and Buckley, R.A.: The disorder → order transformation in iron–cobalt-based alloys. Met. Sci. 7, 48 (1973).
27.ASTM A773/774M-14: Magntic propertics. In Annual Book of ASTM Standards, Vol. 3 (2014); pp. 112.
28.Belyakov, A., Kimura, Y., and Tsuzaki, K.: Microstructure evolution in dual-phase stainless steel during severe deformation. Acta Mater. 54, 2521 (2006).
29.Belyakov, A., Tsuzaki, K., Kimura, Y., and Mishima, Y.: Annealing behavior of a ferritic stainless steel subjected to large-strain cold working. J. Mater. Res. 22, 3042 (2007).
30.Gurao, N.P., Kumar, P., Sarkar, A., Brokmeier, H.G., and Suwas, S.: Simulation of deformation texture evolution during multi axial forging of interstitial free steel. J. Mater. Eng. Perform. 22, 1004 (2013).
31.Kustas, A.B., Sagapuram, D., Chandrasekar, S., and Trumble, K.P.: Deformation and recrystallization texture development in Fe–4% Si subjected to large shear deformation. IOP Conf. Ser. Mater. Sci. Eng. 82, 12054 (2015).
32.Li, S., Beyerlein, I.J., and Bourke, M.A.M.: Texture formation during equal channel angular extrusion of fcc and bcc materials: Comparison with simple shear. Mater. Sci. Eng., A 394, 66 (2005).
33.Li, S., Gazder, A.A., Beyerlein, I.J., Pereloma, E.V., and Davies, C.H.J.: Effect of processing route on microstructure and texture development in equal channel angular extrusion of interstitial-free steel. Acta Mater. 54, 1087 (2006).
34.Li, S., Gazder, A.A., Beyerlein, I.J., Davies, C.H.J., and Pereloma, E.V.: Microstructure and texture evolution during equal channel angular extrusion of interstitial-free steel: Effects of die angle and processing route. Acta Mater. 55, 1017 (2007).
35.Jazaeri, H. and Humphreys, F.J.: The transition from discontinuous to continuous recrystallization in some aluminium alloys II. Acta Mater. 52, 3251 (2004).
36.Jazaeri, H. and Humphreys, F.J.: The transition from discontinuous to continuous recrystallization in some aluminium alloys. Acta Mater. 52, 3239 (2004).
37.Bardos, D.I.: Mean magnetic moments in bcc Fe–Co alloys. J. Appl. Phys. 40, 1371 (1969).
38.Herzer, G.: Grain size dependence of coercivity and permeability. IEEE Trans. Magn. 26, 1397 (1990).
39.Kaibyshev, R., Shipilova, K., Musin, F., and Motohashi, Y.: Continuous dynamic recrystallization in an Al–Li–Mg–Sc alloy during equal-channel angular extrusion. Mater. Sci. Eng., A 396, 341 (2005).
40.Belyakov, A., Sakai, T., Miura, H., Kaibyshev, R., and Tsuzaki, K.: Continuous recrystallization in austenitic stainless steel after large strain deformation. Acta Mater. 50, 1547 (2002).
41.Niendorf, T., Canadinc, D., Maier, H.J., Karaman, I., and Yapici, G.G.: Microstructure-mechanical property relationships in ultrafine-grained NbZr. Acta Mater. 55, 6596 (2007).
42.Purcek, G., Saray, O., Karaman, I., and Maier, H.J.: High strength and high ductility of ultrafine-grained, interstitial-free steel produced by ECAE and annealing. Metall. Mater. Trans. A 43, 1884 (2012).
43.Beyerlein, I.J. and Toth, S.L.: Texture evolution in equal-channel angular extrusion. Prog. Mater. Sci. 54, 427510 (2009).
44.Marcinkowski, M.J. and Polaik, R.M.: A study of the magnetic domain configurations in Fe–Co solid solutions. Acta Metall. 12, 179 (1964).
45.Hall, R.C.: Single crystal anisotropy and magnetostriction constants of several ferromagnetic materials including alloys of NiFe, SiFe, AlFe, CoNi, and CoFe. J. Appl. Phys. 30, 816 (1959).
46.Kustas, A.B., Susan, D.F., Johnson, K.L., Whetten, S.R., Rodriguez, M.A., Dagel, D.J., Michael, J.R., Keicher, D.M., and Argibay, N.: Characterization of the Fe–Co–1.5V soft ferromagnetic alloy processed by laser engineered net shaping (LENS). Addit. Manuf. 21, 4152 (2018).


Related content

Powered by UNSILO

Equal channel angular extrusion for bulk processing of Fe–Co–2V soft magnetic alloys, part II: Texture analysis and magnetic properties

  • Andrew B. Kustas (a1), Joseph R. Michael (a1), Don F. Susan (a1), Ibrahim Karaman (a2) and Taymaz Jozaghi (a3)...


Altmetric attention score

Full text views

Total number of HTML views: 0
Total number of PDF views: 0 *
Loading metrics...

Abstract views

Total abstract views: 0 *
Loading metrics...

* Views captured on Cambridge Core between <date>. This data will be updated every 24 hours.

Usage data cannot currently be displayed.