Hostname: page-component-7c8c6479df-27gpq Total loading time: 0 Render date: 2024-03-28T17:41:16.889Z Has data issue: false hasContentIssue false

Determination of hardness from nanoscratch experiments: Corrections for interfacial shear stress and elastic recovery

Published online by Cambridge University Press:  31 January 2011

Noureddine Tayebi
Affiliation:
Department of General Engineering, University of Illinois at Urbana-Champaign, Urbana, Illinois 61801
Thomas F. Conry*
Affiliation:
Department of General Engineering, University of Illinois at Urbana-Champaign, Urbana, Illinois 61801
Andreas A. Polycarpou
Affiliation:
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, Illinois 61801
*
a) Address all correspondence to this author. e-mail: tconry@uiuc.edu
Get access

Abstract

A frequent application of the nanoscratch technique is to estimate hardness of ultrathin films when substrate effects are encountered with the nanoindentation technique. A model based on the work of Goddard and Wilman, which assumes a rigid-plastic behavior of the deformed surfaces, is commonly used for the determination of hardness from scratch tests, yet it overestimates the hardness of materials by as much as a factor of three at very shallow indentation depths on the order of 1–10 nm. The Goddard and Wilman model was extended in this paper to include the effects of the component of the shear stress tangential to the meridianal plane and the elastic recovery of the plastically deformed surfaces assuming elastic-perfectly-plastic material behavior. The proposed model was subsequently verified by performing nanoscratch experiments on fused quartz, which is homogeneous and isotropic with no known surface layers and with known hardness. The hardness was calculated using both the model based on the work of Goddard and Wilman and the extended model. The hardness calculated using the extended model was in very close agreement with the accepted value of bulk hardness of fused quartz over the range of scratch depths tested, showing the importance of the effects of elastic recovery and interfacial shear stress. The model was further verified for the case of a pure aluminum sample and the native thin film coating of alumina that forms on the surface upon air exposure.

Type
Articles
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Haque, M.A. and Saif, M.T.A., Exp. Mech. 42, 123 (2002).CrossRefGoogle Scholar
2.Oliver, W.C. and Pharr, G.M., J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
3.Doerner, M.F. and Nix, W.D., J. Mater. Res. 1, 601 (1986).CrossRefGoogle Scholar
4.Bhattacharya, A.K. and Nix, W.D., Int. J. Solids Struct. 24, 1287 (1988).CrossRefGoogle Scholar
5.Chen, X. and Vlassak, J.J., J. Mater. Res. 16, 2974 (2001).CrossRefGoogle Scholar
6.Bhushan, B., Williams, V.S., and Shack, R.V., ASME J. of Tribol. 110, 563 (1988).CrossRefGoogle Scholar
7.Tsukamato, Y., Yamaguchi, H., and Yanagisawa, M., Thin Solid Films 154, 171 (1987).CrossRefGoogle Scholar
8.Mohs, F., Grundriss der Mineralogie, (1824), English Translation by Haidinger, W., Treatise of Mineralogy (Constable, Edinburgh, Scotland, 1825).Google Scholar
9.Williams, J., Tribol. Int. 29, 675 (1996).CrossRefGoogle Scholar
10.Li, X. and Bhushan, B., J. Mater. Res. 14, 2328 (1999).CrossRefGoogle Scholar
11.Consiglio, R., Randall, N.X., Bellaton, B., and Stebut, J. von, Thin Solid Films 332, 151 (1998).CrossRefGoogle Scholar
12.Bhushan, B., Handbook of Micro/Nanotribology, 2nd ed. (CRC, Boca Raton, FL, 1999).Google Scholar
13.Bhushan, B., Gupta, K., and Azarian, M., Wear 181–183, 743 (1995).CrossRefGoogle Scholar
14.Kral, E.R., Komvopoulos, K., and Bogy, D.B., ASME J. Tribol. 118, 1 (1996).CrossRefGoogle Scholar
15.Maan, N. and Groenou, A. Broese Van, Wear 42, 365 (1977).CrossRefGoogle Scholar
16.Komvopoulos, K., Saka, N., and Suh, N.P., ASME J. Tribol. 108, 301 (1986).CrossRefGoogle Scholar
17.Buttery, T.C. and Archard, J.F., Proc. Inst. Mech. Eng. 185, 537 (1971).CrossRefGoogle Scholar
18.Brookes, C.A., Green, P., Harrison, P.H., and Moxley, B., J. Phys. D: Appl. Phys. 5, 1284 (1972).CrossRefGoogle Scholar
19.Adler, T.A. and Walters, R.P., Wear 162–164, 713 (1993).CrossRefGoogle Scholar
20.Rodrigo, A., Perillo, P., and Ichimura, H., Surf. Coat. Technol. 124, 87 (2000).CrossRefGoogle Scholar
21.Ichimura, H. and Rodrigo, A., Surf. Coat. Technol. 126, 152 (2000).CrossRefGoogle Scholar
22.Rodrigo, A. and Ichimura, H., Surf. Coat. Technol. 148, 8 (2001).CrossRefGoogle Scholar
23.De Beurs, H., Minholts, G., and Hosson, J.Th.M. De, Wear 132, 59 (1989).CrossRefGoogle Scholar
24.Friction, Lubrication and Wear Technology, ASM Handbook, Vol. 18 (ASM International, New York, 1992).Google Scholar
25.Li, K., Shapiro, Y., and Li, J.C.M., Acta Mater. 46, 5569 (1998).CrossRefGoogle Scholar
26.Briscoe, B.J., Delfino, A., and Pellilo, E., Wear 225–229, Part 1, 319 (1999).CrossRefGoogle Scholar
27.Shaw, M.C., Mech. Chem. Eng. Trans. I. E. Aust., MC8, 73 (1972).Google Scholar
28.Goddard, J. and Wilman, H., Wear 5, 114 (1962).CrossRefGoogle Scholar
29.Komvopoulos, K., Saka, N., and Suh, N.P., ASME J. Tribol. 107, 452 (1985).CrossRefGoogle Scholar
30.Nano-Scratch User Manual, Hysitron, Inc., Minneapolis, MN.Google Scholar
31.Stillwell, N.A. and Tabor, D., Proc. Phys. Soc. London 78, 169 (1961).CrossRefGoogle Scholar
32.Li, Z., Cheng, Y-T., Yang, H.T., and Chandrasekar, S., Surf. Coat. Technol. 154, 124 (2002).CrossRefGoogle Scholar
33.Jardet, V., Zahouni, H., Loubet, J.L., and Mathia, T.G., Wear 218, 8 (1998).CrossRefGoogle Scholar
34.Bucaille, J., Felder, E., and Hochstetter, G., Wear 249, 422 (2001).CrossRefGoogle Scholar
35.Johnson, K.L., J. Mech. Phys. Solids 18, 145 (1970).CrossRefGoogle Scholar
36.Boussinesq, J., Application des potentials a létude de léquilibre du movement des solides elastiques (Gauthier-Villars, Paris, France, 1885).Google Scholar
37.Love, A.E.H., A Treatise on the Mathematical Theory of Elasticity (Dover Publications, New York, 1944).Google Scholar
38.Johnson, K.L., Contact Mechanics (Cambridge University Press, Cambridge, U.K., 1985).CrossRefGoogle Scholar
39.Saif, M.T.A., Zhang, S., Haque, M.A., and Hsia, J., Acta Mater. 50, 2779 (2002).CrossRefGoogle Scholar
40.Shackelford, J.F. and Alexander, W., Materials Science and Engineering Handbook (CRC Press, Boca Raton, FL, 2001).Google Scholar
41.Saha, R. and Nix, W.D., Acta Mater. 50, 23 (2002).CrossRefGoogle Scholar