Hostname: page-component-7c8c6479df-995ml Total loading time: 0 Render date: 2024-03-19T10:28:56.141Z Has data issue: false hasContentIssue false

Analysis of creep behavior of SiC/Al metal matrix composites based on a generalized shear-lag model

Published online by Cambridge University Press:  01 December 2004

Ho J. Ryu
Affiliation:
Dry Process Fuel Technology Division, Korea Atomic Energy Research Institute, Daejeon 305-353, Korea
Kyung H. Chung
Affiliation:
College of Engineering, University of California—Davis, Davis, California 95616
Seung I. Cha
Affiliation:
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, Daejon 305-701, Korea
Soon H. Hong*
Affiliation:
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, Daejon 305-701, Korea
*
a) Address all correspondence to this author.e-mail: shhong@kaist.ac.kr
Get access

Abstract

The creep behaviors of 20 vol% SiCw/2124Al, extruded with different ratios, and SiCp/2124Al, reinforced with 10–30 vol% SiC particles, were investigated to clarify the effects of aspect ratio, alignment, and volume fraction of reinforcement on creep deformation. The effective stresses on the matrix of SiC/Al composites are calculated based on the generalized shear-lag model. The minimum creep rates of SiCw/2124Al extruded with different ratios and SiCp/2124Al reinforced with different volume fractions of SiC particles are found to be similar under a same effective stress on matrix, which is calculated by the generalized shear-lag model. The subgrain sizes in matrices of crept SiC/Al composites are dependent on the effective stress on matrix but not on the applied stress on the composite. It is suggested that the role of SiC reinforcements is to increase the creep resistance of SiC/Al composite by reducing the effective stress on matrix.

Type
Articles
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Li, Y. and Langdon, T.G.: Creep behavior of an AZ91 magnesium alloy reinforced with alumina fibers. Metall. Mater. Trans. A 30A, 2059 (1999).CrossRefGoogle Scholar
2Morimoto, T., Yamaoka, T., Lilholt, H. and Taya, M.: Second stage creep of SiC whisker/6061 aluminum composite at 573K. J. Eng. Mater. Technol. 110, 70 (1988).CrossRefGoogle Scholar
3Nieh, T.G.: Creep rupture of a silicon carbide reinforced aluminum composite. Metall. Trans. A 15A, 139 (1984).CrossRefGoogle Scholar
4Mishira, R.S. and Pandey, A.B.: Some observations on the high-temperature creep behavior of 6061 Al-SiC composites. Metall. Trans. A 21A, 2089 (1990).CrossRefGoogle Scholar
5Li, Y. and Langdon, T.G.: An examination of a substructure-invariant model for the creep of metal matrix composites. Mater. Sci. Eng. A 265, 276 (1999).CrossRefGoogle Scholar
6Gibeling, J.C. and Nix, W.D.: The description of elevated temperature deformation in terms of threshold stresses and back stresses: A review. Mater. Sci. Eng. 45, 123 (1980).CrossRefGoogle Scholar
7Li, Y. and Langdon, T.G.: A unified interpretation of threshold stresses in the creep and high strain rate superplasticity of metal matrix composites. Acta Mater. 47, 3395 (1999).CrossRefGoogle Scholar
8Gonzalez-Doncel, G. and Sherby, O.D.: High temperature creep behavior of metal matrix aluminum–SiC composites. Acta Metall. Mater. 41, 2797 (1993).CrossRefGoogle Scholar
9Mohamed, F.A., Park, K.T. and Lavernia, E.J.: Creep behavior of discontinuous SiC Al composites. Mater. Sci. Eng. A 150, 21 (1992).CrossRefGoogle Scholar
10Park, K.T., Lavernia, E.J. and Mohamed, F.A.: High temperature creep of silicon carbide particulate reinforced aluminum. Acta Metall. Mater. 38, 2149 (1990).CrossRefGoogle Scholar
11Li, Y. and Mohamed, F.A.: An investigation of creep behavior in an SiC–2124 Al composite. Acta Mater. 45, 4775 (1997).CrossRefGoogle Scholar
12Nardone, V.C. and Strife, J.R.: Analysis of the creep behavior of silicon carbide whisker reinforced 2124Al. Metall. Trans. A 18A, 109 (1987).CrossRefGoogle Scholar
13Dragone, T.L. and Nix, W.D.: Geometric factors affecting the internal stress distribution and high temperature creep rate of discontinuous fiber reinforced metals. Acta Metall. Mater. 38, 1941 (1990).CrossRefGoogle Scholar
14Pandey, A.B., Mishra, R.S. and Mahajan, Y.R.: Steady state creep behavior of silicon carbide particulate reinforced aluminum composite. Acta Metall. Mater. 40, 2045 (1992).CrossRefGoogle Scholar
15Cadek, J., Oikawa, H. and Sustek, V.: Threshold creep behaviour of discontinuous aluminium and aluminium alloy matrix composites: An overview. Mater. Sci. Eng. A 190, 9 (1995).CrossRefGoogle Scholar
16Hong, S.H. and Chung, K.H.: High temperature creep behavior of metal matrix composites. Key Eng. Mater. 104, 225 (1995).Google Scholar
17Cox, H.L.: The elasticity and strength of paper and other fibrous materials. Br. J. Appl. Phys. 3, 72 (1952).CrossRefGoogle Scholar
18Nardone, V.C. and Prewo, K.M.: On the strength of discontinuous silicon carbide reinforced aluminum composites. Scripta Metall. Mater. 20, 43 (1986).CrossRefGoogle Scholar
19Nardone, V.C.: Assessment of models used to predict the strength of discontinuous silicon carbide reinforced aluminum composites. Scripta Metall. Mater. 21, 1313 (1987).CrossRefGoogle Scholar
20Ryu, H.J., Cha, S.I. and Hong, S.H.: Generalized shear-lag model for load transfer in SiC/Al metal matrix composites. J. Mater. Res. 18, 2851 (2003).CrossRefGoogle Scholar
21Robinson, S.L. and Sherby, O.D.: Mechanical behavior of polycrystalline tungsten at elevated temperature. Acta Metall. 17, 109 (1969).CrossRefGoogle Scholar
22Nabarro, F.R.N. and Villiers, H.L.: The Physics of Creep (Taylor & Francis, London, U.K., 1995).Google Scholar