Hostname: page-component-7bb8b95d7b-cx56b Total loading time: 0 Render date: 2024-09-13T07:55:26.760Z Has data issue: false hasContentIssue false
  • English
  • Français

Formation of the solidified microstructure of Mg–Al–Zn alloy under a low-voltage pulsed magnetic field

Published online by Cambridge University Press:  05 July 2011

J.W. Fu  and
Y.S. Yang
J.W. Fu
Affiliation:
Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
Y.S. Yang*
Affiliation:
Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
*
a)Address all correspondence to this author. e-mail: ysyang@imr.ac.cn
Get access

Abstract

Effect of a low-voltage pulsed magnetic field (LVPMF) on the solidified microstructure of Mg–Al–Zn alloy has been investigated. Experimental results show that the solidified structure of Mg–Al–Zn alloy can be remarkably refined and that the morphology of α-Mg is transformed from developed dendrite to fine rosette with the application of LVPMF. Magnetization of the solute and solvent in the diffusion layer cannot account for the formation of the rosette α-Mg under LVPMF. A model for the formation of rosette α-Mg under LVPMF has been developed by analyzing the growth behavior of α-Mg dendrite. Morphology change of α-Mg dendrite under LVPMF is caused by Joule heat concentrated on the dendrite tip. Accumulation of Joule heat on the dendrite tip melts the local dendrite tip and increases the radius of curvature. The increased radius of curvature at the dendrite tip lowers the growth rate and results in the formation of rosette α-Mg.

Keywords

Phase transformationMgCrystal growth
Type
Articles
Information
Journal of Materials Research , Volume 26 , Issue 14 , 28 July 2011 , pp. 1688 - 1695
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Friedrich, H.E. and Mordike, B.L.: Magnesium Technology (Springer-Verlag, Berlin, 2006), p. 269.Google Scholar
2.Ma, J.H., Li, J., Gao, Y.L., and Zhai, Q.J.: Grain refinement of pure Al with different electric current pulse modes. Mater. Lett. 63, 142 (2009).CrossRefGoogle Scholar
3.Li, J.M., Li, S.L., Li, J., and Lin, H.T.: Modification of solidification structure by pulse electric discharge. Scr. Metall. Mater. 31, 1691 (1994).Google Scholar
4.Nakada, M., Shiohara, Y., and Flemings, M.C.: Modification of solidification structures by pulse electric discharging. ISIJ Int. 30, 27 (1990).CrossRefGoogle Scholar
5.Song, C.J., Li, Q.S., Li, H.B., and Zhai, Q.J.: Effect of pulse magnetic field on microstructure of austenitic stainless steel during directional solidification. Mater. Sci. Eng., A 485, 403 (2008).CrossRefGoogle Scholar
6.Li, J., Ma, J.H., Gao, Y.L., and Zhai, Q.J.: Research on solidification structure refinement of pure aluminum by electric current pulse with parallel electrodes. Mater. Sci. Eng., A 490, 452 (2008).CrossRefGoogle Scholar
7.Gong, Y.Y., Luo, J., Jing, J.X., Xia, Z.Q., and Zhai, Q.J.: Structure refinement of pure aluminum by pulse magneto-oscillation. Mater. Sci. Eng., A 497, 147 (2008).CrossRefGoogle Scholar
8.Li, X., Ren, Z.M., and Fautrelle, Y.: Effect of a high axial magnetic field on the microstructure in a directionally solidified Al-Al2Cu eutectic alloy. Acta Mater. 54, 5349 (2006).CrossRefGoogle Scholar
9.Barnak, J.P., Sprecher, A.F., and Conrad, H.: Colony (grain) size reduction in eutectic Pb-Sn castings by electropulsing. Scr. Metall. Mater. 32, 879 (1995).CrossRefGoogle Scholar
10.Yang, Y.S., Zhou, Q., and Hu, Z.Q.: The influence of electric current pulses on the microstructure of magnesium alloy AZ91D. Mater. Sci. Forum 488-489, 201 (2005).CrossRefGoogle Scholar
11.Liao, X.L., Zhai, Q.J., Luo, J., Chen, W.J., and Gong, Y.Y.: Refining mechanism of the electric current pulse on the solidification structure of pure aluminum. Acta Mater. 55, 3103 (2007).CrossRefGoogle Scholar
12.Zi, B.T., Ba, Q.X., Cui, J.Z., and Xu, G.M.: Study on axial changes of as-cast structures of Al-alloy sample treated by the novel SPMF technique. Scr. Mater. 43, 377 (2000).Google Scholar
13.Gao, Y.L., Li, Q.S., Gong, Y.Y., and Zhai, Q.J.: Comparative study on structural transformation of low-melting pure Al and high-melting stainless steel under external pulsed magnetic field. Mater. Lett. 61, 4011 (2007).CrossRefGoogle Scholar
14.Li, Q.S., Song, C.J., Li, H.B., and Zhai, Q.J.: Effect of pulsed magnetic field on microstructure of 1Cr18Ni9Ti austenitic stainless steel. Mater. Sci. Eng., A 466, 101 (2007).CrossRefGoogle Scholar
15.Li, X., Fautrelle, Y., and Ren, Z.M.: Influence of a high magnetic field on columnar dendrite growth during directional solidification. Acta Mater. 55, 5333 (2007).CrossRefGoogle Scholar
16.Li, X., Fautrelle, Y., and Ren, Z.M.: Morphological instability of cell and dendrite during directional solidification under a high magnetic field. Acta Mater. 56, 3146 (2008).CrossRefGoogle Scholar
17.Li, X., Fautrelle, Y., Ren, Z.M., Gagnoud, A., Moreau, R., Zhang, Y.D., and Esling, C.: Effect of a high magnetic field on the morphological instability and irregularity of the interface of a binary alloy during directional solidification. Acta Mater. 57, 1689 (2009).CrossRefGoogle Scholar
18.Zimmermann, G., Weiss, A., and Mbaya, Z.: Effect of forced melt flow on microstructure evolution in AlSi7Mg0.6 alloy during directional solidification. Mater. Sci. Eng., A 413, 414, 236 (2005).CrossRefGoogle Scholar
19.Biswas, K., Hermann, R., Das, J., Priede, J., Gerbeth, G., and Acker, J.: Tailoring the microstructure and mechanical properties of Ti–Al alloy using a novel electromagnetic stirring method. Scr. Mater. 55, 1143 (2006).CrossRefGoogle Scholar
20.Wang, B., Yang, Y.S., Zhou, J.X., and Tong, W.H.: Microstructure refinement of AZ91D alloy solidified with pulsed magnetic field. Trans. Nonferrous Met. Soc. China 18, 536 (2008).CrossRefGoogle Scholar
21.Ma, X.P., Li, Y.J., and Yang, Y.S.: Grain refinement effect of a pulsed magnetic field on as-cast superalloy K417. J. Mater. Res. 24, 2670 (2009).CrossRefGoogle Scholar
22.Ma, X.P., Li, Y.J., and Yang, Y.S.: The origin of nuclei and the refinement mechanism for solidified superalloy IN718 under pulsed magnetic field. J. Mater. Res. 24, 3689 (2009).CrossRefGoogle Scholar
23.Christian, J.W.: The Theory of Transformations in Metals and Alloys (Pergamon Press, Oxford, 1975), p. 450.Google Scholar
24.Kurz, W. and Fisher, D.J.: Fundamentals of Solidification (Trans Tech Aedermannsdorf Press, Switzerland, 1984), p. 74.Google Scholar
25.Mullins, W.W. and Sekerka, R.F.: Stability of planar interface during solidification of a dilute binary alloy. J. Appl. Phys. 35, 444 (1964).CrossRefGoogle Scholar
26.Langer, J.S. and Müller-Krumbhaar, H.: Theory of dendritic growth—I. Elements of a stability analysis. Acta Metall. 26, 1681 (1978).CrossRefGoogle Scholar
27.Trivedi, R.: Theory of dendritic growth during the directional solidification of binary alloys. J. Cryst. Growth 49, 219 (1980).CrossRefGoogle Scholar
28.Kurz, W. and Fisher, D.J.: Dendrite growth at the limit of stability: Tip radius and spacing. Acta Metall. 29, 11 (1981).CrossRefGoogle Scholar
29.Wakai, F. and Aldinger, F.: Sintering through surface motion by the difference in mean curvature. Acta Mater. 51, 4013 (2003).CrossRefGoogle Scholar