Skip to main content Accessibility help
×
Home

Design of composite helicopter rotor blades to meet given cross-sectional properties

  • S. L. Lemanski (a1), P. M. Weaver (a1) and G. F. J. Hill (a1)

Abstract

This paper examines the design of a composite helicopter rotor blade to meet given cross-sectional properties. As with many real-world problems, the choice of objective and design variables can lead to a problem with a non-linear and/or non-convex objective function, which would require the use of stochastic optimisation methods to find an optimum. Since the objective function is evaluated from the results of a finite element analysis of the cross section, the computational expense of using stochastic methods would be prohibitive. It is shown that by choosing appropriate simplified design variables, the problem becomes convex with respect to those design variables. This allows deterministic optimisation methods to be used, which is considerably more computationally efficient than stochastic methods. It is also shown that the design variables can be chosen such that the response of each individual cross-sectional property can be closely modelled by a linear approximation, even though the response of a single objective function to many design parameters is non-linear. The design problem may therefore be reformulated into a number of simultaneous linear equations that are easily solved by matrix methods, thus allowing an optimum to be located with the minimum number of computationally expensive finite element analyses.

Copyright

References

Hide All
1. Kameyama, M., Fukunaga, H. and Sekine, H.. Optimum design of composite wing model for aeroelastic properties, 1997, Proceedings of 5th Japan International SAMPE Symposium.
2. Chattopadhyay, A., McCarthy, T.R. and Pagaldipti, N.. Multilevel decomposition procedure for efficient design optimization of helicopter rotor blades, AIAA J, 1995, 33, (2), pp 223230.
3. Jung, S.N., Nagaraj, V.T. and Chopra, I.. Assessment of composite helicopter blade modelling techniques, J Am Helicopter Soc, 1999, 44, (3), pp 188205.
4. Wörndle, R.. Calculation of the cross-section properties and the shear stresses of composite rotor blades, Vertica, 1982, 6, pp 111129.
5. Kosmatka, J.B. and Dong, S.B.. Saint-Venant solutions for prismatic anisotropic beams, Int J of Solids and Structures, 1991, 28, (7), pp 917938
6. Hatch, C. and Lee, A.R.. Determination of the structural properties of helicopter rotor blades by theoretical and experimental methods, 1986, Paper No 67 presented at the 12th European Rotorcraft Forum.
7. Diamond, S.W., Theoretical Prediction of Composite Model Rotor Blade Structural Properties Using Various F.E. Modelling Idealisations, 1996, Defence Research Agency, Farnborough.
8. He, C. and Peters, D.A.. Finite state aeroelastic model for use in rotor design optimisation, J Aircr, 1993, 30, (5), pp 777784.
9. McCarthy, T.R., Chattopadhyay, A. and Zhang, S.. A coupled rotor/wing optimization procedure for high speed tilt-rotor aircraft, 1995, Proceedings of American Helicopter Society 51st Annual Forum, Vol 2.
10. Chattopadhyay, A., McCarthy, T.R. and Seeley, C.E.. Decomposition-based optimisation procedure for high-speed prop-rotors using composite tailoring, J Aircr, 1995, 32, (5), pp 10261033.
11. Chattopadhyay, A. and Narayan, J.. Optimum design of high speed prop-rotors using a multidisciplinary approach, Eng Optimization, 1993, 22, pp 117.
12. Ganguli, R. and Chopra, I.. Aeroelastic optimization of a helicopter rotor with two-cell composite blades, AIAA J, 1996, 34, (4), pp 835854.
13. Chandra, R. and Chopra, I.. Structural behaviour of two-cell composite rotor blades with elastic couplings, AIAA J, 1992, 30, (12), pp 29142924.
14. Hill, G.F.J. and Weaver, P.M.. Analysis of anisotropic prismatic sections, Aeronaut J, April 2004, 108, (1082), pp 197205.
15. Bartholomew, P. and Mercer, A.D., Analysis of an Anisotropic Beam with Arbitrary Cross-Section, Technical Report 84058, Royal Aircraft Establishment.
16. Fukunaga, H.. A solution procedure for determining laminate configurations from lamination parameters, Adv Composite Materials, 1984, 1991, 1, (3), pp 209224.
17. Fukunaga, H. and Sekine, H.. Stiffness design method of symmetric laminates using lamination parameters, AIAA J, 1992, 30, pp 27912793.
18. Miki, M.. Material design of composite laminates with required in-plane elastic properties, Prog in Sci and Eng of Composites, 1982, Hayashi, T., Kawata, K. and Umekawa, S. (Eds), ICCM-IV, Tokyo, Vol 2, pp 17251731.
19. Miki, M.. A Graphical method for designing fibrous laminated composites with required in-plane stiffness, Trans JSCM, 1983, 9, (2), pp 5155.

Related content

Powered by UNSILO

Design of composite helicopter rotor blades to meet given cross-sectional properties

  • S. L. Lemanski (a1), P. M. Weaver (a1) and G. F. J. Hill (a1)

Metrics

Full text views

Total number of HTML views: 0
Total number of PDF views: 0 *
Loading metrics...

Abstract views

Total abstract views: 0 *
Loading metrics...

* Views captured on Cambridge Core between <date>. This data will be updated every 24 hours.

Usage data cannot currently be displayed.